Heat transfer rate per unit area is called (A) Thermal conductivity (B) Heat flux (C) Heat transfer co-efficient (D) Thermal diffusivity

Heat transfer rate per unit area is called
(A) Thermal conductivity
(B) Heat flux
(C) Heat transfer co-efficient
(D) Thermal diffusivity
by

1 Answer

Answer :

(B) Heat flux
by

Related questions

In Fourier's law, the proportionality constant is called the (A) Heat transfer co-efficient (B) Thermal diffusivity (C) Thermal conductivity (D) Stefan-Boltzmann constant

Description : In Fourier's law, the proportionality constant is called the (A) Heat transfer co-efficient (B) Thermal diffusivity (C) Thermal conductivity (D) Stefan-Boltzmann constant

Last Answer : (C) Thermal conductivity

Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Description : Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Last Answer : (A) Mass transfer co-efficient

The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the right face is 10 W/m2 .K. At steady state, the temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Description : The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the ... temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Last Answer : (D) 48.7

Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is ‘3k/l’. If the wall temperature on the outside is held at 25°C, what is the inside wall temperature in degree centigrade?(A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Description : Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is 3k/l'. If the wall temperature ... wall temperature in degree centigrade? (A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Last Answer : (C) 81.25

Nusselt number/Biot number varies (A) Inversely with thermal conductivity (B) Directly with heat transfer co-efficient (C) Directly with thermal conductivity (D) Inversely with the dimension of the solid

Description : Nusselt number/Biot number varies (A) Inversely with thermal conductivity (B) Directly with heat transfer co-efficient (C) Directly with thermal conductivity (D) Inversely with the dimension of the solid

Last Answer : (A) Inversely with thermal conductivity

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Description : What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Last Answer : (A) 2

Thermal diffusivity of a material (A) Has the unit m2 /sec (B) Is defined as K/ρ . Cp (C) Is the ratio of thermal conductivity to thermal capacity (D) All (A), (B) and (C)

Description : Thermal diffusivity of a material (A) Has the unit m2 /sec (B) Is defined as K/ρ . Cp (C) Is the ratio of thermal conductivity to thermal capacity (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/s (B) μ , α and θ all have units of m2/s (C) α and θ have units of m2/s, while μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Description : In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/ ... μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Last Answer : Option C

With increase in temperature, the rate of leaching increases, because the (A) Diffusivity of solute increases (B) Viscosity of solvent decreases (C) Thermal conductivity of solute increases (D) None of these

Description : With increase in temperature, the rate of leaching increases, because the (A) Diffusivity of solute increases (B) Viscosity of solvent decreases (C) Thermal conductivity of solute increases (D) None of these

Last Answer : (A) Diffusivity of solute increases

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Heat flux is the time rate of heat transfer per unit (A) Length (B) Area (C) Volume (D) None of these

Description : Heat flux is the time rate of heat transfer per unit (A) Length (B) Area (C) Volume (D) None of these

Last Answer : (B) Area

Mass transfer co-efficient (K) and diffusivity (D) are related according to film theory as (A) K ∝ D (B) K ∝√D (C) K ∝ D1.5 (D) K ∝ D

Description : Mass transfer co-efficient (K) and diffusivity (D) are related according to film theory as (A) K ∝ D (B) K ∝√D (C) K ∝ D1.5 (D) K ∝ D

Last Answer : (A) K ∝ D

Wetted wall tower experiment determines the (A) Molal diffusivity (B) Volumetric co-efficient (C) Mass transfer co-efficient (D) None of these

Description : Wetted wall tower experiment determines the (A) Molal diffusivity (B) Volumetric co-efficient (C) Mass transfer co-efficient (D) None of these

Last Answer : (C) Mass transfer co-efficient

Mass transfer co-efficient 'K' according to penetration theory varies with mass diffusivity as (A) D0.5 (B) D (C) 1/D (D) D1.5

Description : Mass transfer co-efficient 'K' according to penetration theory varies with mass diffusivity as (A) D0.5 (B) D (C) 1/D (D) D1.5

Last Answer : (A) D0.5

Penetration theory relates the average mass transfer co-efficient (K) with diffusivity (D) as (A) K ∝D (B) K ∝√D (C) K ∝D1.5 (D) K ∝D

Description : Penetration theory relates the average mass transfer co-efficient (K) with diffusivity (D) as (A) K ∝D (B) K ∝√D (C) K ∝D1.5 (D) K ∝D

Last Answer : (B) K ∝√D

The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Description : The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Last Answer : (D) Dependent on the Reynolds number

Heat transfer rate described by Fourier's law will decrease, if the __________ increases. (A) Thermal conductivity (B) Thickness (C) Temperature difference (D) Heat transfer area

Description : Heat transfer rate described by Fourier's law will decrease, if the __________ increases. (A) Thermal conductivity (B) Thickness (C) Temperature difference (D) Heat transfer area

Last Answer : (B) Thickness

Thermal diffusivity of a substance is proportional to (where, k = Thermal conductivity) (A) 1/k (B) k (C) k2 (D) 1/k2

Description : Thermal diffusivity of a substance is proportional to (where, k = Thermal conductivity) (A) 1/k (B) k (C) k2 (D) 1/k2

Last Answer : (B) k

Lewis number, which is important in problems involving simultaneous heat and mass transfer, is the ratio of (A) Mass diffusivity to momentum diffusivity (B) Thermal diffusivity to mass diffusivity (C) Momentum diffusivity to thermal diffusivity (D) None of these

Description : Lewis number, which is important in problems involving simultaneous heat and mass transfer, is the ratio of (A) Mass diffusivity to momentum diffusivity (B) Thermal diffusivity to mass diffusivity (C) Momentum diffusivity to thermal diffusivity (D) None of these

Last Answer : (B) Thermal diffusivity to mass diffusivity

Thermal diffusivity is the most important in heat transfer by (A) Conduction (B) Radiation

Description : Thermal diffusivity is the most important in heat transfer by (A) Conduction (B) Radiation

Last Answer : (A) Conduction

Which of the following has the same dimension as mass diffusivity? (A) Momentum flux (B) Kinematic viscosity (C) Thermal diffusivity (D) Both (B) and (C)

Description : Which of the following has the same dimension as mass diffusivity? (A) Momentum flux (B) Kinematic viscosity (C) Thermal diffusivity (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K = 0.04 W/m.°K and thickness 0.16m is 10 W/m2 . The temperature of the inside wall is - 5°C. The outside wall temperature is (A) 25°C (B) 30°C (C) 35°C (D) 40°C

Description : The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K = 0.04 W/m.°K and thickness 0.16m is 10 W/m2 . The temperature of the inside wall is - 5°C. The outside wall temperature is (A) 25°C (B) 30°C (C) 35°C (D) 40°C

Last Answer : (C) 35°C

A bearing metal should not have (A) Enough plasticity (B) Low thermal conductivity (C) Low co-efficient of friction (D) High toughness

Description : A bearing metal should not have (A) Enough plasticity (B) Low thermal conductivity (C) Low co-efficient of friction (D) High toughness

Last Answer : (B) Low thermal conductivity

Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Description : Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Last Answer : (C) High corrosion resistance

Heat transfer by natural convection is enhanced in system with (A) High viscosity (B) High co-efficient of thermal expansio

Description : Heat transfer by natural convection is enhanced in system with (A) High viscosity (B) High co-efficient of thermal expansio

Last Answer : (B) High co-efficient of thermal expansion

For aluminium, as compared to copper, all the following factors have higher values except (a) specific volume (6) electrical conductivity (c) co-efficient of linear expansion (d) resistance per unit length for same cross-section

Description : For aluminium, as compared to copper, all the following factors have higher values except (a) specific volume (6) electrical conductivity (c) co-efficient of linear expansion (d) resistance per unit length for same cross-section

Last Answer : (6) electrical conductivity

What refers to the rate of thermal radiation emitter per unit area of a body?  A. Thermal conductivity  B. Absorptivity  C. Emissivity  D. Emissive power

Description : What refers to the rate of thermal radiation emitter per unit area of a body?  A. Thermal conductivity  B. Absorptivity  C. Emissivity  D. Emissive power

Last Answer : Emissive power

. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

A bimetallic strip commonly found in home furnace thermostats works because of the difference in this property of the two metals. Is it: w) thermal shock x) thermal conductivity y) thermal expansion z) thermal diffusivity

Description : A bimetallic strip commonly found in home furnace thermostats works because of the difference in this property of the two metals. Is it: w) thermal shock x) thermal conductivity y) thermal expansion z) thermal diffusivity

Last Answer : ANSWER: Y -- THERMAL EXPANSION

Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

Pick out the wrong statement. (A) Reciprocal of the resistance to heat flow is called thermal conductance (B) Unit of thermal conductance is W/°K (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A (D) None of these

Description : Pick out the wrong statement. (A) Reciprocal of the resistance to heat flow is called thermal conductance (B) Unit of thermal conductance is W/°K (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A (D) None of these

Last Answer : (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A

Mass transfer co-efficient is defined as (A) Flux = Co-efficient/concentration difference (B) Co-efficient = Flux/concentration difference (C) Flux=concentration difference/coefficient (D) None of these

Description : Mass transfer co-efficient is defined as (A) Flux = Co-efficient/concentration difference (B) Co-efficient = Flux/concentration difference (C) Flux=concentration difference/coefficient (D) None of these

Last Answer : (B) Co-efficient = Flux/concentration difference

Finned tube heat exchangers (A) Give larger area per tube (B) Use metal fins of low thermal conductivity (C) Facilitate very large temperature drop through tube wall (D) Are used for smaller heat load

Description : Finned tube heat exchangers (A) Give larger area per tube (B) Use metal fins of low thermal conductivity (C) Facilitate very large temperature drop through tube wall (D) Are used for smaller heat load

Last Answer : (A) Give larger area per tube

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

The unit of heat transfer co-efficient in SI unit is (A) J/M2°K (B) W/m2°K (C) W/m°K (D) J/m°K

Description : The unit of heat transfer co-efficient in SI unit is (A) J/M2°K (B) W/m2°K (C) W/m°K (D) J/m°K

Last Answer : (B) W/m2°K

The unit of heat transfer co-efficient is (A) BTU/hr. ft 2°F (B) BTU/hr. °F. ft (C) BTU/hr. °F (D) BTU/hr. ft

Description : The unit of heat transfer co-efficient is (A) BTU/hr. ft 2°F (B) BTU/hr. °F. ft (C) BTU/hr. °F (D) BTU/hr. ft

Last Answer : (A) BTU/hr. ft 2°F

. (NSh /NRe .NSc ) is termed in mass transfer operation as the (A) Stanton number (B) Peclet number (C) Thermal diffusivity (D) Momentum diffusivity

Description : . (NSh /NRe .NSc ) is termed in mass transfer operation as the (A) Stanton number (B) Peclet number (C) Thermal diffusivity (D) Momentum diffusivity

Last Answer : (A) Stanton number

Heat transfer occurs by natural convection because change in temperature causes difference in (A) Viscosity (B) Density (C) Thermal conductivity (D) Heat capacity

Description : Heat transfer occurs by natural convection because change in temperature causes difference in (A) Viscosity (B) Density (C) Thermal conductivity (D) Heat capacity

Last Answer : (B) Density

A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Description : A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Last Answer : (B) 0.025

The critical radius of insulation for a spherical shell is (where, K = thermal conductivity of insulating material h0 = heat transfer coefficient at the outer surface) (A) K/h0 (B) 2K/h0 (C) h0 /K (D) h0 /2K

Description : The critical radius of insulation for a spherical shell is (where, K = thermal conductivity of insulating material h0 = heat transfer coefficient at the outer surface) (A) K/h0 (B) 2K/h0 (C) h0 /K (D) h0 /2K

Last Answer : (B) 2K/h0

Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity (C) In unsteady state heat conduction, heat flows in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Description : Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the ... in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Last Answer : (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

Description : For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

Last Answer : (C) 6.1

Out of the following four assumptions used in the derivation of theequation for LMTD[LMTD = (∆t1- ∆t2)/ln(∆t1/∆t2)], which one is subject to the largest deviationin practice ?(A) Constant overall heat transfer co-efficient.(B) Constant rate of fluid flow(C) Constant specific heat(D) No partial phase change in the system

Description : Out of the following four assumptions used in the derivation of theequation for LMTD [LMTD = (∆t1 - ∆t2 )/ln(∆t1 /∆t2 )], which one is subject to the largest deviation in practice ? (A) Constant ... (B) Constant rate of fluid flow (C) Constant specific heat (D) No partial phase change in the system

Last Answer : (B) Constant rate of fluid flow

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

Which of the following is not a unit of mass transfer co-efficient? (A) Moles transferred/ [(time) (area) (mole fraction)] (B) Moles transferred/ [(time) (area) (mass A/mass B)] (C) Moles transferred/ [(time) (area) (pressure)] (D) None of these

Description : Which of the following is not a unit of mass transfer co-efficient? (A) Moles transferred/ [(time) (area) (mole fraction)] (B) Moles transferred/ [(time) (area) (mass A/mass B)] (C) Moles transferred/ [(time) (area) (pressure)] (D) None of these

Last Answer : (D) None of these

Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Description : Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Last Answer : (B) Requirement of heat transfer area is low