In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

In a vapor-liquid contacting equipment, the overall gas phase mass

transfer co-efficient (M.T.C), KG is related to individual co-efficients

(KG and KL

) as

(A) KG = 1/KG + m/KL

(B) 1/KG = 1/KG + m/KL

(C) 1/KG = 1/KL + m/KG

(D) KG = 1/KL + m/KG

by

1 Answer

Answer :

(B) 1/KG = 1/KG + m/KL


by

Related questions

The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of the following resistance (s) is (are) controlling? (A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Description : The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of ... A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Last Answer : (B) Gas side

The wetted wall tower is used to determine (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system (B) M.T.C. of individual components in a liquid-liquid system (C) M.T.C. of liquid in liquid-gas system (D) The overall M.T.C. of the system

Description : The wetted wall tower is used to determine (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system (B) M.T.C. of individual components in a liquid-liquid system (C) M.T.C. of liquid in liquid-gas system (D) The overall M.T.C. of the system

Last Answer : (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system

The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is(A) 100(B) 10(C) 5(D) 1.

Description : The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is. (A) 100 (B) 10 (C) 5 (D) 1

Last Answer : (B) 10

The relation among various mass transfer co-efficients (M.T.C) for ideal gases is given by (where, Kc & Km are M.T.C. for equimolar counter diffusion with concentration & mole fraction respectively as the driving force. and, Kp= M.T.C. for diffusion of a gas through a stagnant inert gas with pressure as driving force.) (A) Kc = Kp = Km (B) Kc = Kp /RT = Km . RT/P (C) Kc = Kp . RT = Km . RT/p (D) None of these

Description : The relation among various mass transfer co-efficients (M.T.C) for ideal gases is given by (where, Kc & Km are M.T.C. for equimolar counter diffusion with concentration & mole fraction respectively as the driving ... (C) Kc = Kp . RT = Km . RT/p (D) None of these

Last Answer : (C) Kc = Kp . RT = Km . RT/p

A first order gaseous phase reaction is catalysed by a non-porous solid. The kinetic rate constant and the external mass transfer co-efficients are k and kg respectively. The effective rate constant (ke ff) is given by (A) ke ff = k + kg (B) ke ff = (k+ kg )/2 (C) ke ff = (kkg ) 1/2 (D) 1/ke ff = 1/k + 1/kg

Description : A first order gaseous phase reaction is catalysed by a non-porous solid. The kinetic rate constant and the external mass transfer co-efficients are k and kg respectively. The effective rate constant (ke ff) is given by (A) ke ff = k + kg ( ... + kg )/2 (C) ke ff = (kkg ) 1/2 (D) 1/ke ff = 1/k + 1/kg

Last Answer : (D) 1/ke ff = 1/k + 1/kg

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient(B) Increasing the liquid film co-efficient(C) Increasing the total pressure(D) Decreasing the total pressure

Description : The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient (B) Increasing the liquid film co-efficient (C) Increasing the total pressure (D) Decreasing the total pressure

Last Answer : (A) Increasing the gas film co-efficient

Flooding in a vapor-liquid contacting equipment occurs in a tray, when the pressure drop through a tray is __________ the liquid head available in the downcomer. (A) Less than (B) More than (C) Same as (D) Very much less

Description : Flooding in a vapor-liquid contacting equipment occurs in a tray, when the pressure drop through a tray is __________ the liquid head available in the downcomer. (A) Less than (B) More than (C) Same as (D) Very much less

Last Answer : (B) More than

. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

The advantage of backward feed multiple effect evaporators over forward feed units is that (A) Heat sensitive material can be handled (B) There is no additional cost of pumping (C) Most concentrated liquid is at highest temperature (D) Equal heat transfer co-efficients exist in various effects

Description : The advantage of backward feed multiple effect evaporators over forward feed units is that (A) Heat sensitive material can be handled (B) There is no additional cost of pumping ... liquid is at highest temperature (D) Equal heat transfer co-efficients exist in various effects

Last Answer : (C) Most concentrated liquid is at highest temperature

In an interphase heat transfer process, the equilibrium state corresponds to equality of temperature in the two phases, while the condition for equilibrium in an interphase mass transfer process is equality of (A) Concentrations (B) Chemical potentials (C) Activity co-efficients (D) Mass transfer co-efficients

Description : In an interphase heat transfer process, the equilibrium state corresponds to equality of temperature in the two phases, while the condition for equilibrium in an interphase mass transfer process is ... B) Chemical potentials (C) Activity co-efficients (D) Mass transfer co-efficients

Last Answer : (A) Concentrations

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only

Out of the following four assumptions used in the derivation of theequation for LMTD[LMTD = (∆t1- ∆t2)/ln(∆t1/∆t2)], which one is subject to the largest deviationin practice ?(A) Constant overall heat transfer co-efficient.(B) Constant rate of fluid flow(C) Constant specific heat(D) No partial phase change in the system

Description : Out of the following four assumptions used in the derivation of theequation for LMTD [LMTD = (∆t1 - ∆t2 )/ln(∆t1 /∆t2 )], which one is subject to the largest deviation in practice ? (A) Constant ... (B) Constant rate of fluid flow (C) Constant specific heat (D) No partial phase change in the system

Last Answer : (B) Constant rate of fluid flow

Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Description : Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Last Answer : (B) Requirement of heat transfer area is low

For absorbing a sparingly soluble gas in a liquid (A) Gas side mass transfer co-efficient should be increased (B) Liquid side mass transfer co-efficient should be increased (C) Liquid side mass transfer co-efficient should be decreased (D) Mass transfer co-efficient must be kept constant

Description : For absorbing a sparingly soluble gas in a liquid (A) Gas side mass transfer co-efficient should be increased (B) Liquid side mass transfer co-efficient should be increased (C) Liquid side mass transfer co-efficient should be decreased (D) Mass transfer co-efficient must be kept constant

Last Answer : (B) Liquid side mass transfer co-efficient should be increased

Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Description : Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Last Answer : (A) Mass transfer co-efficient does not account for gas-liquid diffusion

Which of the following liquid-vapor contacting devices provides maximum contact surface area for a particular duty? (A) Sieve plate column (B) Bubble cap column (C) Randomly packed column (D) Wetted wall column

Description : Which of the following liquid-vapor contacting devices provides maximum contact surface area for a particular duty? (A) Sieve plate column (B) Bubble cap column (C) Randomly packed column (D) Wetted wall column

Last Answer : (D) Wetted wall column

For condensation of pure vapors, if the heat transfer co-efficients in filmwise and drop-wise condensation are respectively hf and hd , then (A) hf = hd (B) hf > hd (C) hf < hd (D) hf could be greater or smaller than hd

Description :  For condensation of pure vapors, if the heat transfer co-efficients in filmwise and drop-wise condensation are respectively hf and hd , then (A) hf = hd (B) hf > hd (C) hf < hd (D) hf could be greater or smaller than hd

Last Answer : (C) hf < hd

A vessel with a volume of cubic meter contains liquid water and water vapor ion equilibrium at 600 kPa. The liquid water has mass of1kg. Using the steam table, calculate the mass of the water vapor.  A. 0.99kg  B. 1.57 kg  C. 2.54 kg  D. 3.16 kg Formula: from the steam table at 600kPa vƒ = 0.001101 m^3 / kg vg = 0.3157 m^3 / kg Vtot = mƒ vƒ + mg vg mg = (tot-mƒ vƒ) / vg

Description : A vessel with a volume of cubic meter contains liquid water and water vapor ion equilibrium at 600 kPa. The liquid water has mass of1kg. Using the steam table, calculate the mass of the water vapor.  A. 0.99kg  B. 1.57 kg  C ... / kg vg = 0.3157 m^3 / kg Vtot = mƒ vƒ + mg vg mg = (tot-mƒ vƒ) / vg

Last Answer : 3.16 kg

Mass transfer co-efficient (K) and diffusivity (D) are related according to film theory as (A) K ∝ D (B) K ∝√D (C) K ∝ D1.5 (D) K ∝ D

Description : Mass transfer co-efficient (K) and diffusivity (D) are related according to film theory as (A) K ∝ D (B) K ∝√D (C) K ∝ D1.5 (D) K ∝ D

Last Answer : (A) K ∝ D

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Mass transfer co-efficient of liquid is (A) Affected more by temperature than that for gases (B) Affected much less by temperature than that for gases

Description : Mass transfer co-efficient of liquid is (A) Affected more by temperature than that for gases (B) Affected much less by temperature than that for gases

Last Answer : (A) Affected more by temperature than that for gases

The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Description : The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Last Answer : (D) Dependent on the Reynolds number

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Last Answer : (B) Always between h1 and h2

Overall heat transfer co-efficient of a particular tube is U1 . If the same tube with some dirt deposited on either side has coefficient U2 , then (A) U1 = U2 (B) U2 > U1 (C) U1 > U2 (D) U1 = dirt factor - U2

Description : Overall heat transfer co-efficient of a particular tube is U1 . If the same tube with some dirt deposited on either side has coefficient U2 , then (A) U1 = U2 (B) U2 > U1 (C) U1 > U2 (D) U1 = dirt factor - U2

Last Answer : (A) U1 = U2

Which of the following has the lowest overall heat transfer co-efficient? (A) Dowtherm (B) Molten sodium (C) Water (D) Air

Description : Which of the following has the lowest overall heat transfer co-efficient? (A) Dowtherm (B) Molten sodium (C) Water (D) Air

Last Answer : (D) Air

The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year ofoperation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co￾efficient at this time is(A) 1200 W/m2.K(B) 894 W/m2.K(C) 333 W/m2.K(D) 287 W/m2.K

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

Which of the following is true for Virial equation of state? (A) Virial co-efficients are universal constants (B) Virial co-efficients 'B' represents three body interactions (C) Virial co-efficients are function of temperature only (D) For some gases, Virial equations and ideal gas equations are the same

Description : Which of the following is true for Virial equation of state? (A) Virial co-efficients are universal constants (B) Virial co-efficients 'B' represents three body interactions (C) Virial co-efficients ... of temperature only (D) For some gases, Virial equations and ideal gas equations are the same

Last Answer : (C) Virial co-efficients are function of temperature only

If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor. (A) Increase (B) Decrease (C) Not affect (D) Increase the condensing film co-efficient as well as

Description : If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor. (A) Increase (B) Decrease (C) Not affect (D) Increase the condensing film co-efficient as well as

Last Answer : (B) Decrease

Activity co-efficient is a measure of the (A) Departure from ideal solution behaviour (B) Departure of gas phase from ideal gas law (C) Vapour pressure of liquid (D) None of these

Description : Activity co-efficient is a measure of the (A) Departure from ideal solution behaviour (B) Departure of gas phase from ideal gas law (C) Vapour pressure of liquid (D) None of these

Last Answer : (A) Departure from ideal solution behaviour

The main purpose of providing fins on heat transfer surface is to increase the (A) Temperature gradient (B) Mechanical strength of the equipment (C) Heat transfer area (D) Heat transfer co-efficient

Description : The main purpose of providing fins on heat transfer surface is to increase the (A) Temperature gradient (B) Mechanical strength of the equipment (C) Heat transfer area (D) Heat transfer co-efficient

Last Answer : (C) Heat transfer area

Indirect contact heat exchangers are preferred over direct contact heat exchangers, because (A) Heat transfer co-efficient are high (B) There is no risk of contamination (C) There is no mist formation (D) Cost of equipment is lower

Description : Indirect contact heat exchangers are preferred over direct contact heat exchangers, because (A) Heat transfer co-efficient are high (B) There is no risk of contamination (C) There is no mist formation (D) Cost of equipment is lower

Last Answer : (B) There is no risk of contamination

H2S is being absorbed in a gas absorber unit. The height of the transfer unit based on the overall mass transfer coefficient on the gas side is 0.4 m. The equilibrium data is given by, y = 1.5 x. The bulk concentration of H2S has to be reduced from 0.05 to 0.001 mole fraction in the gas side. The height of the tower (in metres) corresponding to an operating line given by, y = 5x + 0.001 is (A) 2.0 (B) 1.56 (C) 1.0

Description : H2S is being absorbed in a gas absorber unit. The height of the transfer unit based on the overall mass transfer coefficient on the gas side is 0.4 m. The equilibrium data is given by, y = 1.5 x. The bulk concentration of H2S ... by, y = 5x + 0.001 is (A) 2.0 (B) 1.56 (C) 1.0

Last Answer : (A) 2.0

Van Laar equation deals with the activity co-efficients in (A) Binary solutions (B) Ternary solutions (C) Azeotropic mixture only (D) None of these

Description : Van Laar equation deals with the activity co-efficients in (A) Binary solutions (B) Ternary solutions (C) Azeotropic mixture only (D) None of these

Last Answer : (A) Binary solutions

A 10m^3 vessel initially contains 5 m^3 of liquid water and 5 m^3 of saturated water vapor at 100 kPa. Calculate the internal energy of the system using the steam table.  A. 5 x10^5 kJ  B. 8x10^5 kJ  C. 1 x10^6 kJ  D. 2 x10^6 kJ Formula: fromthe steamtable vƒ = 0.001043 m^3 / kg vg = 1.6940 m^3 / kg u ƒ= 417.3 kJ/kg ug= 2506kJ/kg formula: Mvap = V vap/vg M liq = Vliq/ vƒ u =uƒM liq + ug M vap

Description : A 10m^3 vessel initially contains 5 m^3 of liquid water and 5 m^3 of saturated water vapor at 100 kPa. Calculate the internal energy of the system using the steam table.  A. 5 x10^5 kJ  B. 8x10^5 kJ  C. 1 ... 3 kJ/kg ug= 2506kJ/kg formula: Mvap = V vap/vg M liq = Vliq/ vƒ u =uƒM liq + ug M vap

Last Answer : 2 x10^6 kJ

The average heat transfer co-efficient over the entire length of the plate (ha ) and the local heat transfer co-efficient (hL ), in case of heat transfer over a flat plate in laminar zone is related as (A) ha = 0.8hL (B) ha = 2hL (C) ha = hL (D) ha = 5hL

Description : The average heat transfer co-efficient over the entire length of the plate (ha ) and the local heat transfer co-efficient (hL ), in case of heat transfer over a flat plate in laminar zone is related as (A) ha = 0.8hL (B) ha = 2hL (C) ha = hL (D) ha = 5hL

Last Answer : (B) ha = 2hL

Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Description : Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Last Answer : (D) None of these

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Description : The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Last Answer : (B) 4 0.8

The rough value of diffusion co-efficient of water vapor into air at 25°C may be about __________ cm2 /sec. (A) 0.25 (B) 2.5 (C) 1.25 (D) 0.0025

Description : The rough value of diffusion co-efficient of water vapor into air at 25°C may be about __________ cm2 /sec. (A) 0.25 (B) 2.5 (C) 1.25 (D) 0.0025

Last Answer : (A) 0.25

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Description : The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Last Answer : (C) Some

For contacting a highly soluble gas with a liquid (A) Bubble the gas through liquid (B) Spray the liquid on gas stream (C) Either (A) or (B) would suffice (D) None of these

Description : For contacting a highly soluble gas with a liquid (A) Bubble the gas through liquid (B) Spray the liquid on gas stream (C) Either (A) or (B) would suffice (D) None of these

Last Answer : (A) Bubble the gas through liquid

Out of the following gas-liquid contacting devices, for a given set of operating conditions, gas pressure drop is the least in __________ tower. (A) Wetted wall (B) Bubble cap (C) Perforated tray (D) Packed

Description : Out of the following gas-liquid contacting devices, for a given set of operating conditions, gas pressure drop is the least in __________ tower. (A) Wetted wall (B) Bubble cap (C) Perforated tray (D) Packed

Last Answer : (A) Wetted wall

Which of the following gas-liquid contacting devices incurs the least pressure drop for a particular duty? (A) Grid tray tower (B) Perforated tray tower (C) Wetted wall tower (D) Bubble cap tower

Description : Which of the following gas-liquid contacting devices incurs the least pressure drop for a particular duty? (A) Grid tray tower (B) Perforated tray tower (C) Wetted wall tower (D) Bubble cap tower

Last Answer : (D) Bubble cap tower

At 60° C, vapour pressure of methanol and water are 84.562 kPa and 19.953 kPa respectively. An aqueous solution of methanol at 60° C exerts a pressure of 39.223 kPa; the liquid phase and vapour phase mole fractions of methanol are 0.1686 and 0.5714 respectively. Activity co-efficient of methanol is (A) 1.572 (B) 1.9398 (C) 3.389

Description : At 60° C, vapour pressure of methanol and water are 84.562 kPa and 19.953 kPa respectively. An aqueous solution of methanol at 60° C exerts a pressure of 39.223 kPa; the liquid phase and vapour phase mole ... respectively. Activity co-efficient of methanol is (A) 1.572 (B) 1.9398 (C) 3.389

Last Answer : (A) 1.572