The thickness of condensate layer in filmwise condensation depends on the (A) Condensation rate (B) Surface configuration (C) Liquid flow rate from the surface (D) All (A), (B) and (C)

The thickness of condensate layer in filmwise condensation depends on
the
(A) Condensation rate
(B) Surface configuration
(C) Liquid flow rate from the surface
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The boiling point of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Description : Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The ... of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Last Answer : (B) Filmwise condensation takes place on non-wettable surfaces

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

For condensation of pure vapors, if the heat transfer co-efficients in filmwise and drop-wise condensation are respectively hf and hd , then (A) hf = hd (B) hf > hd (C) hf < hd (D) hf could be greater or smaller than hd

Description :  For condensation of pure vapors, if the heat transfer co-efficients in filmwise and drop-wise condensation are respectively hf and hd , then (A) hf = hd (B) hf > hd (C) hf < hd (D) hf could be greater or smaller than hd

Last Answer : (C) hf < hd

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation will (A) Increase (B) Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

The local surface conductance for laminar film condensation on vertical surface is (where, t = film thickness) (A) ∝ t (B) ∝ 1/t (C) ∝ √t (D) Independent of 't

Description : The local surface conductance for laminar film condensation on vertical surface is (where, t = film thickness) (A) ∝ t (B) ∝ 1/t (C) ∝ √t (D) Independent of 't

Last Answer : (B) ∝ 1/t

The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Description : The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Last Answer : (A) Cumulatively increases

A process stream of dilute aqueous solution flowing at the rate of10 Kg.s -1 is to be heated. Steam condensate at 95°C is available for heating purpose, also at a rate of 10 Kg.s -1 . A 1 - 1 shell and tube heat exchanger is available. The best arrangement is (A) Counter flow with process stream on shell side (B) Counter flow with process stream on tube side (C) Parallel flow with process stream on shell side (D) Parallel flow with process stream on tube side

Description : A process stream of dilute aqueous solution flowing at the rate of10 Kg.s -1 is to be heated. Steam condensate at 95°C is available for heating purpose, also at a rate of 10 Kg.s -1 . A 1 ... side (C) Parallel flow with process stream on shell side (D) Parallel flow with process stream on tube side

Last Answer : (A) Counter flow with process stream on shell side

A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will (A) Increase (B) Decrease (C) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Description : A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted ... ) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Last Answer : Option C

The thickness of the layer of insulation on the conductor, in cables, depends upon (a) Reactive power (b) Power factor (c) Voltage (d) Current carrying capacity

Description : The thickness of the layer of insulation on the conductor, in cables, depends upon (a) Reactive power (b) Power factor (c) Voltage (d) Current carrying capacity

Last Answer : (c) Voltage

The ratio of hydrodynamic boundary layer to thermal boundary layer thickness in case of liquid metals is (A) < 1 (B) 1 (C) > 1 (D) 2

Description : The ratio of hydrodynamic boundary layer to thermal boundary layer thickness in case of liquid metals is (A) < 1 (B) 1 (C) > 1 (D) 2

Last Answer : (A) < 1

. The condensate obtained on compression of wet natural gas is termed as (A) Liquefied natural gasoline (B) Natural gasoline (C) Liquid natural gas (D) None of these

Description : . The condensate obtained on compression of wet natural gas is termed as (A) Liquefied natural gasoline (B) Natural gasoline (C) Liquid natural gas (D) None of these

Last Answer : (B) Natural gasoline

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

For flow over a flat plate, the ratio of thermal boundary layer thickness, 'xt' and hydrodynamic boundary layer thickness 'x' is equal to (where, NPr = Prandtl number) (A) NPr (B) NPr 1/3 (C) NPr -1 (D) NPr -1/3

Description : For flow over a flat plate, the ratio of thermal boundary layer thickness, 'xt' and hydrodynamic boundary layer thickness 'x' is equal to (where, NPr = Prandtl number) (A) NPr (B) NPr 1/3 (C) NPr -1 (D) NPr -1/3

Last Answer : (B) NPr 1/3

For flow past a flat plate, if ‘x’ is the distance along the plate in the direction of flow, the boundary layer thickness is proportional to (A) √x (B) 1/√x (C) x (D) 1/x Answe

Description : For flow past a flat plate, if ‘x’ is the distance along the plate in the direction of flow, the boundary layer thickness is proportional to (A) √x (B) 1/√x (C) x (D) 1/x Answe

Last Answer : (A) √x

In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Description : In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Last Answer : (B) Increase gradually

The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Description : The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Last Answer : (B) x0.8

In a counter-current liquid extractor (A) Both liquids flow at fixed rate (B) Both liquids can have any desired flow rate (C) Only one of the liquids may be pumped at any desired rate (D) Liquid’s flow rate depends upon the temperature and pressure

Description : In a counter-current liquid extractor (A) Both liquids flow at fixed rate (B) Both liquids can have any desired flow rate (C) Only one of the liquids may be pumped at any desired rate (D) Liquid’s flow rate depends upon the temperature and pressure

Last Answer : (C) Only one of the liquids may be pumped at any desired rate

Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Last Answer : (D) Boiling of a liquid on a hot surface

Brunauer, Emmet and Teller (BET) equation is used to determine the specific surface area of a porous particle but not the pore volume & the porosity of the catalyst bed. Which of the following postulates is not used to derive BET equation? (A) Langmuir's assumption applies to every adsorbed layer (B) There is no dynamic equilibrium between successive layer (C) The adsorbed layer may be polymolecular in thickness and the heat of adsorption in each layer (except the first one) is involved in each of the evaporation process (D) None of these

Description : Brunauer, Emmet and Teller (BET) equation is used to determine the specific surface area of a porous particle but not the pore volume & the porosity of the catalyst bed. Which of the following postulates ... (except the first one) is involved in each of the evaporation process (D) None of these

Last Answer : (B) There is no dynamic equilibrium between successive layer

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Condensate is the liquid formed when steam passes from the ________ to the ______ state. a. Vapor, solid b. Solid, liquid c. Vapor, liquid d. None

Description : Condensate is the liquid formed when steam passes from the ________ to the ______ state. a. Vapor, solid b. Solid, liquid c. Vapor, liquid d. None

Last Answer : c. Vapor, liquid

The _______ system includes anywhere that the steam condenses to form liquid water. a. Loop b. Power c. Liquid d. Condensate

Description : The _______ system includes anywhere that the steam condenses to form liquid water. a. Loop b. Power c. Liquid d. Condensate

Last Answer : d. Condensate

02. The separation of flow occurs when the hydrodynamic boundary layer thickness is reduced to zero. A) AgreeB) Disagree

Description : 02. The separation of flow occurs when the hydrodynamic boundary layer thickness is reduced to zero. A) Agree B) Disagree

Last Answer : A

A centrifugal filtration unit operating at a rotational speed of w has inner surface of the liquid (density ρL) located at a radial distance R from the axis of rotation. The thickness of the liquid film is δ and no cake is formed. The initial pressure drop during filtration is (A) ½w 2 . R 2 . ρL (B) ½w 2 . δ 2 . ρL (C) ½w 2 . δρL (2R + δ) (D) ½w 2 . R . ρL(R + 2δ)

Description : A centrifugal filtration unit operating at a rotational speed of w has inner surface of the liquid (density ρL) located at a radial distance R from the axis of rotation. The thickness of the liquid film is δ and no cake is formed. The ... . ρL (C) ½w 2 . δρL (2R + δ) (D) ½w 2 . R . ρL(R + 2δ)

Last Answer : (C) ½w 2 . δρL (2R + δ)

The main factor which affects the infiltration capacity, is (A) Thickness of saturated layer (B) Depth of surface detention (C) Soil moisture (D) All the above

Description : The main factor which affects the infiltration capacity, is (A) Thickness of saturated layer (B) Depth of surface detention (C) Soil moisture (D) All the above

Last Answer : Answer: Option D

For a given liquid, the rate of evaporation depends on 1. the temperature of the liquid 2. the temperature of air 3. the surface area of the liquid Which of the above factors is/are correct? (a) 1 only (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : For a given liquid, the rate of evaporation depends on 1. the temperature of the liquid 2. the temperature of air 3. the surface area of the liquid Which of the above factors is/are correct? (a) 1 only (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : Ans:(d)

Before working on an electric cargo winch master switch or controller, you should _____________. A. spray the gasket surface with a solvent B. drain condensate from the box C. open the circuit breaker in the power supply and tag D. heat the switch box to remove any moisture

Description : Before working on an electric cargo winch master switch or controller, you should _____________. A. spray the gasket surface with a solvent B. drain condensate from the box C. open the circuit breaker in the power supply and tag D. heat the switch box to remove any moisture

Last Answer : Answer: C

For __________ drying, the effects of velocity, temperature and humidity of the gas and the thickness of the solid are the same. (A) Unsaturated surface (B) Constant rate (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : For __________ drying, the effects of velocity, temperature and humidity of the gas and the thickness of the solid are the same. (A) Unsaturated surface (B) Constant rate (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

For a given ambient air temperature with increase in the thickness of insulation of a hot cylindrical pipe, the rate of heat loss from the surface would (A) Decrease(B) Increase(C) First decrease and then increase(D) First increase and then decrease

Description : For a given ambient air temperature with increase in the thickness of insulation of a hot cylindrical pipe, the rate of heat loss from the surface would (A) Decrease (B) Increase (C) First decrease and then increase (D) First increase and then decrease

Last Answer : (D) First increase and then decrease

Why rate of condensation is higher on a polished surface compared to rusty surface ?

Description : Why rate of condensation is higher on a polished surface compared to rusty surface ?

Last Answer : Polished surface promotes drop wise condensation and does not wet the surface.

The capacity of a belt conveyor depends upon two factors. If one is the cross-section of the load, the other is the __________ of the belt. (A) Speed (B) Thickness (C) Length (D) None of these

Description : The capacity of a belt conveyor depends upon two factors. If one is the cross-section of the load, the other is the __________ of the belt. (A) Speed (B) Thickness (C) Length (D) None of these

Last Answer : (A) Speed

Filtration capacity of a rotary drum vacuum filter depends upon the (A) Cake thickness (B) Characteristics of the feed slurry (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Filtration capacity of a rotary drum vacuum filter depends upon the (A) Cake thickness (B) Characteristics of the feed slurry (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The actual temperature drop across the heating surface in an evaporator depends on the (A) Feed (B) Depth of liquid over heating surface (C) Pressure difference between steam chest and vapour space (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface in an evaporator depends on the (A) Feed (B) Depth of liquid over heating surface (C) Pressure difference between steam chest and vapour space (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pressure exerted by a liquid depends upon its (A) Surface tension (B) Density (C) Viscosity

Description : Pressure exerted by a liquid depends upon its (A) Surface tension (B) Density (C) Viscosity

Last Answer : Option B

The major reason of hydrodynamic noise (i.e., noise resulting from liquid flow) is (A) Pipe vibrations (B) Cavitation (C) Boundary layer separation (D) Fluctuation in liquid flow

Description : The major reason of hydrodynamic noise (i.e., noise resulting from liquid flow) is (A) Pipe vibrations (B) Cavitation (C) Boundary layer separation (D) Fluctuation in liquid flow

Last Answer : (B) Cavitation

Condensation of a vapour-gas mixture just begins, when (where, p = partial pressure of the vapour P = vapour pressure of the liquid). (A) p = P (B) p >>P (C) p < P (D) p << P

Description : Condensation of a vapour-gas mixture just begins, when (where, p = partial pressure of the vapour P = vapour pressure of the liquid). (A) p = P (B) p >>P (C) p < P (D) p

Last Answer : (A) p = P

Smog is (A) Nothing but black smoke (B) A combination of smoke and fog (C) A liquid particle resulting from vapor condensation (D) A solid particle e.g. fly-ash

Description : Smog is (A) Nothing but black smoke (B) A combination of smoke and fog (C) A liquid particle resulting from vapor condensation (D) A solid particle e.g. fly-ash

Last Answer : (B) A combination of smoke and fog

Venturimeter is used to measure: (1) rate of flow of liquids (2) liquid pressure (3) surface tension (4) liquid density

Description : Venturimeter is used to measure: (1) rate of flow of liquids (2) liquid pressure (3) surface tension (4) liquid density

Last Answer : rate of flow of liquids

Thickness of thermal boundary layer is more compared to that of hydrodynamic boundary layer, when the value of Prandtl number is (A) 1 (B) < 1 (C) > 1 (D) > 5

Description : Thickness of thermal boundary layer is more compared to that of hydrodynamic boundary layer, when the value of Prandtl number is (A) 1 (B) < 1 (C) > 1 (D) > 5

Last Answer : (B) < 1

. If Prandtl number is greater than the Schmidt number, then the (A) Thermal boundary layer lies inside the concentration boundary layer (B) Concentration boundary layer lies inside the thermal boundary layer (C) Thermal & concentration boundary layers are of equal thickness (D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other two

Description : . If Prandtl number is greater than the Schmidt number, then the (A) Thermal boundary layer lies inside the concentration boundary layer (B) Concentration boundary layer lies inside the thermal boundary ... (D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other two

Last Answer : (A) Thermal boundary layer lies inside the concentration boundary layer

A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature at the two sides of the wall are 400 and 1200°K, then the temperature drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Description : A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature ... drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Last Answer : (D) 160

A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature difference across the wall is 36°C. The temperature difference across the layer A is __________ °C. (A) 6 (B) 12 (C) 18 (D) 24

Description : A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature ... difference across the layer A is __________ °C. (A) 6 (B) 12 (C) 18 (D) 24

Last Answer : (B) 12

Which of the following is a measure of the agglutinating (i.e., binding) property of coal? (A) Thickness of plastic layer (B) Caking index (C) Swelling index (D) Gray-king index

Description : Which of the following is a measure of the agglutinating (i.e., binding) property of coal? (A) Thickness of plastic layer (B) Caking index (C) Swelling index (D) Gray-king index

Last Answer : (B) Caking index

Boundary layer separation is caused by the (A) Reduction of pressure to vapour pressure (B) Boundary layer thickness reducing to zero (C) Adverse pressure gradient (D) Reduction of pressure gradient to zero

Description : Boundary layer separation is caused by the (A) Reduction of pressure to vapour pressure (B) Boundary layer thickness reducing to zero (C) Adverse pressure gradient (D) Reduction of pressure gradient to zero

Last Answer : (D) Reduction of pressure gradient to zero

Boundary layer separation is caused by the (A) Reduction of pressure below vapour pressure (B) Reduction of pressure gradient to zero (C) Adverse pressure gradient (D) Reduction of boundary layer thickness to zero

Description : Boundary layer separation is caused by the (A) Reduction of pressure below vapour pressure (B) Reduction of pressure gradient to zero (C) Adverse pressure gradient (D) Reduction of boundary layer thickness to zero

Last Answer : (C) Adverse pressure gradient