. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

. A dilute aqueous solution is to be concentrated in an evaporator

system. High pressure steam is available. Multiple effect evaporator system

is employed, because

(A) Total heat transfer area of all the effects is -less than that in a single

effect evaporator system

(B) Total amount of vapor produced per Kg of feed steam in a multiple effect

system is much higher than in a single effect

(C) Boiling point elevation in a single effect system is much higher than that

in any effect in a multi-effect system

(D) Heat transfer co-efficient in a single effect is much lower than that in any

effect in a multi-effect system

by

1 Answer

Answer :

(B) Total amount of vapor produced per Kg of feed steam in a multiple effect

system is much higher than in a single effect

by

Related questions

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

The capacity of double-effect evaporator is less than half of the capacity of two single effects, each of which is operating over same terminal temperature difference, when the (A) Solution has an elevation of boiling point (B) Evaporators operate under vacuum (C) Evaporators operate at atmospheric pressure (D) None of these

Description : The capacity of double-effect evaporator is less than half of the capacity of two single effects, each of which is operating over same terminal temperature difference, when the (A) Solution has ... B) Evaporators operate under vacuum (C) Evaporators operate at atmospheric pressure (D) None of these

Last Answer : (A) Solution has an elevation of boiling point

A multiple effect evaporator as compared to a single effect evaporator of the same capacity has (A) Lower heat transfer area (B) Lower steam economy (C) Higher steam economy (D) Higher solute concentration in the product

Description : A multiple effect evaporator as compared to a single effect evaporator of the same capacity has (A) Lower heat transfer area (B) Lower steam economy (C) Higher steam economy (D) Higher solute concentration in the product

Last Answer : (C) Higher steam economy

Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature (C) Double pipe heat exchangers are mostly used in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Description : Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat ... in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Last Answer : (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature

Economy of a multiple effect evaporator is not influenced much by the (A) Boiling point elevations (B) Temperature of the feed (C) Rate of heat transfer (D) Ratio of the weight of the thin liquor to thick liquor

Description : Economy of a multiple effect evaporator is not influenced much by the (A) Boiling point elevations (B) Temperature of the feed (C) Rate of heat transfer (D) Ratio of the weight of the thin liquor to thick liquor

Last Answer : (A) Boiling point elevations

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in the tubes of natural circulation evaporators is in the range of 0.3 to 0.9 metre/second (C) Duhring's plot is used for calculating the concentration of solution (D) In a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Description : Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in ... a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Last Answer : (C) Duhring's plot is used for calculating the concentration of solution

The advantage of backward feed multiple effect evaporators over forward feed units is that (A) Heat sensitive material can be handled (B) There is no additional cost of pumping (C) Most concentrated liquid is at highest temperature (D) Equal heat transfer co-efficients exist in various effects

Description : The advantage of backward feed multiple effect evaporators over forward feed units is that (A) Heat sensitive material can be handled (B) There is no additional cost of pumping ... liquid is at highest temperature (D) Equal heat transfer co-efficients exist in various effects

Last Answer : (C) Most concentrated liquid is at highest temperature

A process stream of dilute aqueous solution flowing at the rate of10 Kg.s -1 is to be heated. Steam condensate at 95°C is available for heating purpose, also at a rate of 10 Kg.s -1 . A 1 - 1 shell and tube heat exchanger is available. The best arrangement is (A) Counter flow with process stream on shell side (B) Counter flow with process stream on tube side (C) Parallel flow with process stream on shell side (D) Parallel flow with process stream on tube side

Description : A process stream of dilute aqueous solution flowing at the rate of10 Kg.s -1 is to be heated. Steam condensate at 95°C is available for heating purpose, also at a rate of 10 Kg.s -1 . A 1 ... side (C) Parallel flow with process stream on shell side (D) Parallel flow with process stream on tube side

Last Answer : (A) Counter flow with process stream on shell side

The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

It is desired to concentrate a 20% salt solution (20 kg of salt in 100 kg of solution) to a 30% salt solution in an evaporator. Consider a feed of 300 kg/min at 30°C. The boiling point of the solution is 110°C, the latent heat of vaporisation is 2100 kJ/kg and the specific heat of the solution is 4 kJ/kg.K. The rate at which the heat has to be supplied in (kJ/min) to the evaporator is (A) 3.06 × 10 5 (B) 6.12 × 10 5 (C) 7.24 × 10 5 (D) 9.08 × 10

Description : It is desired to concentrate a 20% salt solution (20 kg of salt in 100 kg of solution) to a 30% salt solution in an evaporator. Consider a feed of 300 kg/min at 30°C. The boiling point of the solution is 110°C, the latent heat of ... 3.06 10 5 (B) 6.12 10 5 (C) 7.24 10 5 (D) 9.08 10

Last Answer : (A) 3.06 × 10

A backward feed multiple effect evaporator is better than forward feed for concentrating cold feed, because it provides (A) Higher economy (B) Lower capacity (C) Both (A) & (B) (D) Lower economy

Description : A backward feed multiple effect evaporator is better than forward feed for concentrating cold feed, because it provides (A) Higher economy (B) Lower capacity (C) Both (A) & (B) (D) Lower economy

Last Answer : (A) Higher economy

In a multiple effect evaporator, the effect of boiling point elevation is to (A) Reduce the capacity (B) Reduce the economy (C) Increase the economy (D) None of these

Description : In a multiple effect evaporator, the effect of boiling point elevation is to (A) Reduce the capacity (B) Reduce the economy (C) Increase the economy (D) None of these

Last Answer : (A) Reduce the capacity

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Steam side heat transfer co-efficient in an evaporator is in the range of __________ kcal/hr.m2°C. (A) 10-50 (B) 100-500 (C) 1000-1500 (D) 5000-15000

Description : Steam side heat transfer co-efficient in an evaporator is in the range of __________ kcal/hr.m2°C. (A) 10-50 (B) 100-500 (C) 1000-1500 (D) 5000-15000

Last Answer : (D) 5000-15000

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient(B) Increasing the liquid film co-efficient(C) Increasing the total pressure(D) Decreasing the total pressure

Description : The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient (B) Increasing the liquid film co-efficient (C) Increasing the total pressure (D) Decreasing the total pressure

Last Answer : (A) Increasing the gas film co-efficient

. In a backward feed multiple effect evaporator (A) Feed is introduced in the first effect (B) Feed flows from low pressure to high pressure (C) No pumps are required between successive effects (D) None of these

Description : . In a backward feed multiple effect evaporator (A) Feed is introduced in the first effect (B) Feed flows from low pressure to high pressure (C) No pumps are required between successive effects (D) None of these

Last Answer : (B) Feed flows from low pressure to high pressure

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Evaporation of 1kg of water from a solution in a single effect evaporator requires about __________ kg of steam. (A) 0.4 - 0.6 (B) 1-1.3 (C) 1.8-2 (D) 2 - 2.4

Description : Evaporation of 1kg of water from a solution in a single effect evaporator requires about __________ kg of steam. (A) 0.4 - 0.6 (B) 1-1.3 (C) 1.8-2 (D) 2 - 2.4

Last Answer : (B) 1-1.3

. An evaporator while concentrating an aqueous solution from 10 to 40% solids evaporates 30000 kg of water. The amount of solids handled by the system in kg is (A) 4000 (B) 9000 (C) 4600 (D) 3000

Description : . An evaporator while concentrating an aqueous solution from 10 to 40% solids evaporates 30000 kg of water. The amount of solids handled by the system in kg is (A) 4000 (B) 9000 (C) 4600 (D) 3000

Last Answer : (A) 4000

For concentrating an aqueous solution of a material like anhydrous Na2SO4, whose solubility decreases with rise in temperature, the most suitable evaporator is a __________ evaporator. (A) High pressure (B) Vacuum (C) Backward feed (D) None of these

Description : For concentrating an aqueous solution of a material like anhydrous Na2SO4, whose solubility decreases with rise in temperature, the most suitable evaporator is a __________ evaporator. (A) High pressure (B) Vacuum (C) Backward feed (D) None of these

Last Answer : (B) Vacuum

. Boiling point elevation for a strong and concentrated solution is found by Duhring's rule, which states that at the same pressure, the boiling point of a solution is a linear function of the __________ of pure water. (A) Boiling point (B) Dynamic viscosity (C) Kinematic viscosity (D) Density

Description : . Boiling point elevation for a strong and concentrated solution is found by Duhring's rule, which states that at the same pressure, the boiling point of a solution is a linear function of the __________ of pure water. (A) Boiling point (B) Dynamic viscosity (C) Kinematic viscosity (D) Density

Last Answer : (A) Boiling point

In a forward feed multiple effect evaporator, the pressure is (A) Highest in last effect (B) Lowest in last effect (C) Same in all effects (D) Dependent on the number of effects

Description : In a forward feed multiple effect evaporator, the pressure is (A) Highest in last effect (B) Lowest in last effect (C) Same in all effects (D) Dependent on the number of effects

Last Answer : (B) Lowest in last effect

Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward feeding in multiple effect evaporation (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Description : Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward ... (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Last Answer : (A) Get economical temperature difference by using moderate pressure steam

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

Black liquor generated during paper manufacture is concentrated in a (A) Single effect evaporator (B) Single effect evaporator followed by a crystalliser (C) Multiple effect evaporator (D) Multiple effect evaporators followed by a crystalliser

Description : Black liquor generated during paper manufacture is concentrated in a (A) Single effect evaporator (B) Single effect evaporator followed by a crystalliser (C) Multiple effect evaporator (D) Multiple effect evaporators followed by a crystalliser

Last Answer : (C) Multiple effect evaporator

The advantage of using a 1 - 2 shell and tube heat exchanger over a 1 - 1 shell and tube heat exchanger is (A) Lower tube side pressure drop (B) Lower shell side pressure drop (C) Higher tube side heat transfer co-efficient (D) Higher shell side heat transfer co-efficient

Description : The advantage of using a 1 - 2 shell and tube heat exchanger over a 1 - 1 shell and tube heat exchanger is (A) Lower tube side pressure drop (B) Lower shell side pressure drop (C) Higher tube side heat transfer co-efficient (D) Higher shell side heat transfer co-efficient

Last Answer : (C) Higher tube side heat transfer co-efficient

Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The boiling point of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Description : Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The ... of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Last Answer : (B) Filmwise condensation takes place on non-wettable surfaces

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

In a forward feed multiple effect evaporator unit (A) Viscosity of liquid is highest in first effect (B) Transfer from effect to effect is done by pumps (C) No pump is required to withdraw the product from the last effect (D) None of these

Description : In a forward feed multiple effect evaporator unit (A) Viscosity of liquid is highest in first effect (B) Transfer from effect to effect is done by pumps (C) No pump is required to withdraw the product from the last effect (D) None of these

Last Answer : (D) None of these

Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Last Answer : (D) Boiling of a liquid on a hot surface

In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Description : In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Last Answer : (B) 1/KG = 1/KG + m/KL

Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than that of the damp material (C) Ratio of its capacity to economy equals the steam consumption in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Description : Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than ... in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Last Answer : (B) Thermal conductivity of a dry material is more than that of the damp material

Small scale evaporation is done in a (A) Heat exchanger (B) Condenser(C) Multiple effect evaporator(D) Steam jacketed kettle

Description : Small scale evaporation is done in a (A) Heat exchanger (B) Condenser (C) Multiple effect evaporator (D) Steam jacketed kettle

Last Answer : (D) Steam jacketed kettle

Economy of an evaporator is influenced by the (A) Steam pressure (B) Feed temperature (C) Number of effect (D) Both (B) & (C)

Description : Economy of an evaporator is influenced by the (A) Steam pressure (B) Feed temperature (C) Number of effect (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

Multipass heat exchangers are used (A) Because of simplicity of fabrication (B) For low heat load (C) To obtain higher heat transfer co-efficient and shorter tube (D) To reduce the pressure drop

Description : Multipass heat exchangers are used (A) Because of simplicity of fabrication (B) For low heat load (C) To obtain higher heat transfer co-efficient and shorter tube (D) To reduce the pressure drop

Last Answer : (C) To obtain higher heat transfer co-efficient and shorter tube

Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Description : Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Last Answer : (B) Flexibility possible in the baffle arrangement

Which of the following properties is lower for a solution than for the pure solvent? w) osmotic pressure x) vapor pressure y) temperature z) boiling point

Description : Which of the following properties is lower for a solution than for the pure solvent? w) osmotic pressure x) vapor pressure y) temperature z) boiling point

Last Answer : ANSWER: X -- VAPOR PRESSURE

Saturated steam at 1 atm is discharged from a turbine at 1200 kg/h. Superheated steam at 300 0C and 1 atm is needed as a feed to a heat exchanger. To produce it, the turbine discharge stream is mixed with superheated steam at 400 0C, 1 atm and specific volume of 3.11 m 3 /kg. Calculate the amount of superheated steam at 300 0C produced and the volumetric flow rate of the 400 0C steam.

Description : Saturated steam at 1 atm is discharged from a turbine at 1200 kg/h. Superheated steam at 300 0C  and 1 atm is needed as a feed to a heat exchanger. To produce it, the turbine discharge ... amount of superheated steam at 300 0C produced and the volumetric flow rate of the  400 0C steam.

Last Answer : Solution 1. Mass balance of water 1200 + m1 = m2 ………………………………………… (1) …………………….1 mark 2. Energy balance (1200 kg/h)(2676 kJ/kg) + m1(3278 kJ/kg)

A multiple effect evaporator has a capacity to process 4000 kg of solid caustic soda per day, when it is concentrating from 10% to 25% solids. The water evaporated in kg per day is (A) 6000 (B) 24000 (C) 60000 (D) 48000

Description : A multiple effect evaporator has a capacity to process 4000 kg of solid caustic soda per day, when it is concentrating from 10% to 25% solids. The water evaporated in kg per day is (A) 6000 (B) 24000 (C) 60000 (D) 48000

Last Answer : (B) 24000

or the same heat transfer area and the terminal conditions, the ratio of the capacities of a single effect evaporator to a triple effect evaporator is (A) 3 (B) 0.33 (C) 1 (D) 1.33

Description : or the same heat transfer area and the terminal conditions, the ratio of the capacities of a single effect evaporator to a triple effect evaporator is (A) 3 (B) 0.33 (C) 1 (D) 1.33

Last Answer : (C) 1

Indirect contact heat exchangers are preferred over direct contact heat exchangers, because (A) Heat transfer co-efficient are high (B) There is no risk of contamination (C) There is no mist formation (D) Cost of equipment is lower

Description : Indirect contact heat exchangers are preferred over direct contact heat exchangers, because (A) Heat transfer co-efficient are high (B) There is no risk of contamination (C) There is no mist formation (D) Cost of equipment is lower

Last Answer : (B) There is no risk of contamination

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Economy of a multiple effect evaporator depends upon the (A) Heat balance consideration (B) Rate of heat transfer (C) Both (A) and (B) (D) Neither (A) nor (B

Description : Economy of a multiple effect evaporator depends upon the (A) Heat balance consideration (B) Rate of heat transfer (C) Both (A) and (B) (D) Neither (A) nor (B

Last Answer : (A) Heat balance consideration

Reason for operating an evaporator in multiple effects is to secure (A) Increased steam economy (B) Decreased steam consumption (C) Both (A) and (B) (D) Increased capacity

Description : Reason for operating an evaporator in multiple effects is to secure (A) Increased steam economy (B) Decreased steam consumption (C) Both (A) and (B) (D) Increased capacity

Last Answer : (C) Both (A) and (B)

If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Last Answer : (B) Always between h1 and h2