Properties of plastics

Properties of plastics
by

1 Answer

Answer :

Properties of plastics:-

1. Light in weight.

2. Easy workability. Easy to shape and mould.

3. Highly resistant to corrosion.

4. Highly resistant to abrasion., moistuer and greases.

5. Good thermal and electrical insulators.

6. Good strength and rigidity.

7. Absorbent of vibrations and sound.

8. Good resistant to most of the chemicals.

9. Impermeable to water.

10. Low fabrication cost.

11. Good dimensional stability.

12. Can be made transparent or coloured.
by

Related questions

Properties of moulding sand are

Description : Properties of moulding sand are

Last Answer : Properties of moulding sand are: i) Cohesiveness or (strength) of sand,  ii) Permeability (Porosity) iii) Plasticity  iv) Thermal Stability v) Refractoriness  vi) Flow ability, vii) ... be reusable and should produce good casting surface. x) It should be bad conductor of heat.

Explain any four properties of Moulding sand.

Description : Explain any four properties of Moulding sand. 

Last Answer : 1. Porosity: Molten metal always contain a certain amount of dissolved gases, which are evolved when the metal freezes the molten metal coming in contact with the moist sand , generates steam or ... to the casting. Refractoriness is measured by the sinter point of the sand rather than its melting

Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication(C) Develop new improved properties not present in the original resin(D) All (A), (B) and (C)

Description : Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication (C) Develop new improved properties not present in the original resin (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication (C) Develop new improved properties not present in the original resins (D) All (A), (B) and (C)

Description : Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication (C) Develop new improved properties not present in the original resins (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The plastics made from cellulose resin (A) Are as clear as glass (B) Are tough and strong (C) Possess excellent electrical properties (D) All the above

Description : The plastics made from cellulose resin (A) Are as clear as glass (B) Are tough and strong (C) Possess excellent electrical properties (D) All the above

Last Answer : Answer: Option D

Radial drilling machine

Description : Radial drilling machine

Last Answer : Radial drilling machine: A radial drilling machine is illustrated in Fig. This is really meant to drill holes in bigger and heavier work pieces, which cannot be manipulated so that the centre of the hole ... and a hole drilled at the required location, without shifting the heavy work piece.

Thread cutting operation

Description : Thread cutting operation

Last Answer : Thread cutting operation:- The principle of thread cutting is to produce a helical groove on cylindrical/conical surfaces by feeding the tool longitudinally when the job is revolved between centers. In this operation, ... The longitudinal feed is equal to the pitch of the thread to be cut.

Combination Dies

Description : Combination Dies

Last Answer : Combination Dies: In this die more than one operation may be performed at one station. It is difficult from compound die in that in this die, a cutting operation is combined with a bending or drawing ... a complete tool consists of a pair of mating members for producing work in a press.

Cutting Speed

Description : Cutting Speed

Last Answer : Cutting Speed: - It is the speed at which the metal is removed by the tool from the work piece. In lathe it is the peripheral speed of the work past the cutting tool expressed in meter per ... degree of surface finish, rigidity of the machine tool being used, and type of coolant being used. 

Advantages/Merits of Cold Working

Description : Advantages/Merits of Cold Working

Last Answer : Advantages/Merits of Cold Working 1. Cold working increases the strength and hardness of the material due to the strain hardening which would be beneficial in some situations. there is no possibility ... costs are high and as such it is used when large quantities of similar components are required

what is Forging ?

Description : what is Forging ?

Last Answer : Forging : Forging is defined as controlled plastic deformation of metals at elevated temperatures into a pre-determined size or shape using compressive forces exerted through some type of die by a hammer or press. ... , 4. Upset forging, 5. Swing forging 6. Cored forging, 7. Rotary forging.

Classify presses. Describe one in brief.

Description : Classify presses. Describe one in brief.

Last Answer : A) According to source of power: a) Mechanical press b) Hydraulic press B) According to number of slides: a) Single action press b) Double action press c) Triple action press C) ... perform the necessary operation. The ram is fitted with punch and the job is resting on the bed.

Direct Extrusion process

Description : Direct Extrusion process

Last Answer : Direct Extrusion process Direct extrusion process is shown in fig. The raw material used is a billet. It consists of a press operated ram and a cylinder or container into which the heated ... for extruding long extrudes. 2) Support of the ram becomes a problem as work length increases.

Welding Defects

Description : Welding Defects 

Last Answer : Welding Defects  Welding defects Explanation and causes 1. Cracks Cracks occur when localized stresses exceed the ultimate tensile strength of material. These stresses are developed due to shrinkage ... Too fast a travel, Bad welding technique, Too great a heat build-up.

Types of rolling mills and its applications

Description : Types of rolling mills and its applications

Last Answer : Types of rolling mills and its applications (1) Two-high rolling mill: used in blooming and slabbing mills (2) Three-high rolling mill: used for making plates or sections. (3) Four- ... : This mill is used for rolling stainless steel and other high strength steel sheets of thin gauge.

Types of slotting machine

Description : Types of slotting machine

Last Answer : 1. Puncher slotter 2. Precision slotter 3. Production slotter  Working Principle of Slotting machine:- The slotting machine is a reciprocating machine tool in which, The vertical slide holding the cutting ... longitudinal and cross feeds, a rotary feed motion is also provided in the work table. 

Differentiate between soldering and brazing

Description : Differentiate between soldering and brazing

Last Answer : Answer: Comparison of brazing and soldering

Safety practices in foundry

Description : Safety practices in foundry

Last Answer : 1. Even trace amounts of MOISTURE and MOLTEN METAL don't mix; Steam explosions are the cause of death in foundries. 2. NEVER put water on a metal fire. This can cause a HUGE EXPLOSION ... operation. 16. Educate yourself beforehand and always be careful of your own and bystander safety.

Single point Cutting tool signature

Description : Single point Cutting tool signature

Last Answer : The shape of a tool is specified in a special sequence and this special sequence is called tool signature. The tool signature is given below (i) Back rake angle (ii) Side rake angle (iii) ... rake, end relief, side relief, end cutting edge, side cutting edge angle and 0.8 mm nose radius.

Explain with neat sketch the working principle of MIG.

Description : Explain with neat sketch the working principle of MIG.

Last Answer : In metal-arc inert gas welding the Weld area is shielded by an effectively inert atmosphere of argon, helium, carbon dioxide, or various other gas mixtures . The consumable bare Wire is fed automatically ... of the molten-weld puddle. Multiple-weld layers can be deposited at the joint. 

Compare between Hot rolling and Cold rolling.

Description : Compare between Hot rolling and Cold rolling.

Last Answer : Hot rolling Cold rolling  Metal is fed to the rolls after being heated above the recrytallization temperature. Metal is fed to the rolls when it is below the recrytallization temperature. ... Hot rolling is the father of the cold rolling. Cold rolling follows the hot rolling.

State the applications of TIG welding.

Description : State the applications of TIG welding.

Last Answer : The applications of TIG welding are as follows: 1. Mostly used to weld aluminum and aluminum alloys. 2. It is used to weld stainless steel, carbon base alloy, copper base alloy, nickel base alloy etc. 3. It is used to welding dissimilar metals. 4. It is mostly used in aerospace industries.

State the applications of rolling.

Description : State the applications of rolling.

Last Answer : Applications of rolling are as follows: 1. Concrete reinforcing bars. 2. Plates. 3. Wire rods. 4. Sheet and strip. 5. Rails. 6. Piping and tubes. 7. Body panels. 8. Construction materials

List any four casting defects.

Description : List any four casting defects.

Last Answer : The various types of casting defects are as follows: 1. Gas Porosity: Blowholes, open holes, pinholes. 2. Shrinkage defects: shrinkage cavity. 3. Mold material defects: Cut and washes, ... Pouring metal defects: Cold shut, misrun, slag inclusion. Metallurgical defects: Hot tears, hot spot.

List any four materials used for pattern making

Description : List any four materials used for pattern making

Last Answer : The various types of materials used are as follows: 1. Wood 2. Metal. 3. Plastic. 4. Plaster. 5. Wax.

Define Feed and speed in shaping machine

Description : Define Feed and speed in shaping machine

Last Answer : 1) Feed: Feed (S) is the relative movement of the work or tool in a direction perpendicular to the axis of reciprocation of the ram per double stroke. It is expressed in mm per stroke. 2) Speed: ... speed is the speed at which the metal is removed by the cutting tool in a period of one minute.

List any four accessories used on lathe.

Description : List any four accessories used on lathe.

Last Answer : The various accessories used in lathe are as follows. 1) Lathe centers 2) Carriers or driving dog 3) catch plates 4) Chucks 5) Face plates 6) Angle plates 7) Mandrels 8) Rests

List types of chips produced in machining process.

Description : List types of chips produced in machining process.

Last Answer : The various types of chips produced in machining process are as follows: 1. Continuous chips: According to its name, continuous chips have a continuous segment. . 2. Discontinuous chips or segmental chips: ... chip is same as the continuous chips except a built edge is form at the face of tool.

Why is it better to use plant and animal based products in place of petroluem and plastics?

Description : Why is it better to use plant and animal based products in place of petroluem and plastics?

Last Answer : This is my midterm essay question which I have researched on my own. But I am at a loss.

I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Description : I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Last Answer : answer:Strength is how strong a material is – basically breaking load. Modulus is how flexible or stretchy a material is. Does not matter if the test coupon breaks or not. Think of uncooked spaghetti vs rubber band.

When I do the dishes, why do the plastics sometimes end up greasy?

Description : When I do the dishes, why do the plastics sometimes end up greasy?

Last Answer : answer:I've noticed that too, must have something to do with the grease sticking to the plastic more. I always use tons of soap and rinse really well as I also have a phobia about tasting soap. ... run it for the same reason and because somewhere, deep down, I think it is inferior to hand washing.

Which plastics can helium support?

Description : Which plastics can helium support?

Last Answer : Most if not all plastics are porous and Helium is a small molecule and will pass through the plastic over time. You could try sealing the sculpture with a sealer and that my help contain the ... their balloons to give them long float time of sometimes weeks with the Mylar balloons going even longer.

Why not get a small chipper and chip non-recyclable plastics into small pieces before dumping?

Description : Why not get a small chipper and chip non-recyclable plastics into small pieces before dumping?

Last Answer : Because a landfill full of sharp plastic shards is not good for the enviroment. Also given that it won't speed up the rate decomposition I think it isn't worth the effort. Add on ... overall it's probably worsefor the enviroment. It would be better to boycot companies that use plastic packaging.

Do you remember the many questions on safe/unsafe plastics for water bottles, food storage, Nalgene, etc?

Description : Do you remember the many questions on safe/unsafe plastics for water bottles, food storage, Nalgene, etc?

Last Answer : answer:Here's a summary; http://tinyurl.com/3jdkmj And one of many from ask-public: http://www.ask-public.com/disc/466/water-bottles-plastic-glass-stainless-steel-or/ Similar articles in all ... (the white waxy, shiny coating). Tomatoes and other acid foods may leach more severely. Buyer beware.

Should we start mining old landfill sites for plastics and other recyclable material?

Description : Should we start mining old landfill sites for plastics and other recyclable material?

Last Answer : I don’t see why not! I think it could be worth it. Then we wouldnt have to cut down as many trees to get new stuff. All the stuff at the dump is just going to sit there anyways.

what are extruded plastics

Description : what are extruded plastics

Last Answer : Need Answer

How can we reduce the use of plastics in our daily life?

Description : How can we reduce the use of plastics in our daily life?

Last Answer : Usage of plastics should be banned by the government. First and Foremost thing is the role of an individual in reducing the usage of plastics. People should carry a cloth bag while going to shops ... grocery shops, markets etc. Steel or glass containers should be used at homes for storing things.

Would a low-temp glue gun be better than a high-temp glue gun for plastics?

Description : Would a low-temp glue gun be better than a high-temp glue gun for plastics?

Last Answer : A low temperature glue gun would be best because there would be less damage to the plastic from the heated glue.

Which of the following is a biodegradable waste? (1) Wool (2) Polythene bags (3) Plastics (4) Nylon

Description : Which of the following is a biodegradable waste? (1) Wool (2) Polythene bags (3) Plastics (4) Nylon

Last Answer : (1) Wool

On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because – (1) metals have higher thermal capacity than plastics (2) plastics have a lower density than metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals

Description : On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because - (1) metals ... metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals

Last Answer : (3) metals are good conductors of heat Explanation: On a chilly day, the room temperature is lower than our body temperature. Since metals have a higher coefficient of thermal conductivity than plastic, they ... from our fingers will flow to the metal cap much more quickly than to the plastic body.

'Corrosion-resistant material' and 'noncorrodible material' will include which of the following ____________. A. plastics B. silver C. copper-nickel D. all of the above

Description : 'Corrosion-resistant material' and 'noncorrodible material' will include which of the following ____________. A. plastics B. silver C. copper-nickel D. all of the above

Last Answer : Answer: D

The substances used in colour paints, fil- ters, plastics and other materials?

Description : The substances used in colour paints, fil- ters, plastics and other materials?

Last Answer : Pigments

Which type of plastics is used for mak- ing adhesives; button etc?

Description : Which type of plastics is used for mak- ing adhesives; button etc?

Last Answer : Urea formaldehyde

Plastics are generally?

Description : Plastics are generally?

Last Answer : Synthetic polymers

Bakelite (phenol-formaldehyde) resin cannot be used as (A) Decorative paint (B) Decorative laminates (C) Electrical insulation (D) Glass reinforced plastics

Description : Bakelite (phenol-formaldehyde) resin cannot be used as (A) Decorative paint (B) Decorative laminates (C) Electrical insulation (D) Glass reinforced plastics

Last Answer : (A) Decorative paint

Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Description : Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Last Answer : (C) Combination of solid & liquid

__________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion

Description : __________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion

Last Answer : (C) Transfer

Pick out the correct statement. (A) Plastics are good conductors of heat and electricity (B) All the polymers are highly crystalline in nature (C) Polymers can be vaporised by heating to a very high temperature (D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Description : Pick out the correct statement. (A) Plastics are good conductors of heat and electricity (B) All the polymers are highly crystalline in nature (C) Polymers can be vaporised by heating to ... D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Last Answer : (D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450

Description : Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450

Last Answer : (B) 150