what is Forging ?

what is Forging ?
by

1 Answer

Answer :

Forging : Forging is defined as controlled plastic deformation of metals at elevated temperatures into a pre-determined size or shape using compressive forces exerted through some type of die by a hammer or press.

Types of forging method:

1. Drop forging,

2. Press forging,

3. Hot bar forging,

4. Upset forging,

5. Swing forging

6. Cored forging,

7. Rotary forging.
by

Related questions

Radial drilling machine

Description : Radial drilling machine

Last Answer : Radial drilling machine: A radial drilling machine is illustrated in Fig. This is really meant to drill holes in bigger and heavier work pieces, which cannot be manipulated so that the centre of the hole ... and a hole drilled at the required location, without shifting the heavy work piece.

Thread cutting operation

Description : Thread cutting operation

Last Answer : Thread cutting operation:- The principle of thread cutting is to produce a helical groove on cylindrical/conical surfaces by feeding the tool longitudinally when the job is revolved between centers. In this operation, ... The longitudinal feed is equal to the pitch of the thread to be cut.

Properties of moulding sand are

Description : Properties of moulding sand are

Last Answer : Properties of moulding sand are: i) Cohesiveness or (strength) of sand,  ii) Permeability (Porosity) iii) Plasticity  iv) Thermal Stability v) Refractoriness  vi) Flow ability, vii) ... be reusable and should produce good casting surface. x) It should be bad conductor of heat.

Combination Dies

Description : Combination Dies

Last Answer : Combination Dies: In this die more than one operation may be performed at one station. It is difficult from compound die in that in this die, a cutting operation is combined with a bending or drawing ... a complete tool consists of a pair of mating members for producing work in a press.

Cutting Speed

Description : Cutting Speed

Last Answer : Cutting Speed: - It is the speed at which the metal is removed by the tool from the work piece. In lathe it is the peripheral speed of the work past the cutting tool expressed in meter per ... degree of surface finish, rigidity of the machine tool being used, and type of coolant being used. 

Properties of plastics

Description : Properties of plastics

Last Answer : Properties of plastics:- 1. Light in weight. 2. Easy workability. Easy to shape and mould. 3. Highly resistant to corrosion. 4. Highly resistant to abrasion., moistuer and greases. 5. Good ... 10. Low fabrication cost. 11. Good dimensional stability. 12. Can be made transparent or coloured.

Advantages/Merits of Cold Working

Description : Advantages/Merits of Cold Working

Last Answer : Advantages/Merits of Cold Working 1. Cold working increases the strength and hardness of the material due to the strain hardening which would be beneficial in some situations. there is no possibility ... costs are high and as such it is used when large quantities of similar components are required

Classify presses. Describe one in brief.

Description : Classify presses. Describe one in brief.

Last Answer : A) According to source of power: a) Mechanical press b) Hydraulic press B) According to number of slides: a) Single action press b) Double action press c) Triple action press C) ... perform the necessary operation. The ram is fitted with punch and the job is resting on the bed.

Direct Extrusion process

Description : Direct Extrusion process

Last Answer : Direct Extrusion process Direct extrusion process is shown in fig. The raw material used is a billet. It consists of a press operated ram and a cylinder or container into which the heated ... for extruding long extrudes. 2) Support of the ram becomes a problem as work length increases.

Welding Defects

Description : Welding Defects 

Last Answer : Welding Defects  Welding defects Explanation and causes 1. Cracks Cracks occur when localized stresses exceed the ultimate tensile strength of material. These stresses are developed due to shrinkage ... Too fast a travel, Bad welding technique, Too great a heat build-up.

Types of rolling mills and its applications

Description : Types of rolling mills and its applications

Last Answer : Types of rolling mills and its applications (1) Two-high rolling mill: used in blooming and slabbing mills (2) Three-high rolling mill: used for making plates or sections. (3) Four- ... : This mill is used for rolling stainless steel and other high strength steel sheets of thin gauge.

Types of slotting machine

Description : Types of slotting machine

Last Answer : 1. Puncher slotter 2. Precision slotter 3. Production slotter  Working Principle of Slotting machine:- The slotting machine is a reciprocating machine tool in which, The vertical slide holding the cutting ... longitudinal and cross feeds, a rotary feed motion is also provided in the work table. 

Differentiate between soldering and brazing

Description : Differentiate between soldering and brazing

Last Answer : Answer: Comparison of brazing and soldering

Safety practices in foundry

Description : Safety practices in foundry

Last Answer : 1. Even trace amounts of MOISTURE and MOLTEN METAL don't mix; Steam explosions are the cause of death in foundries. 2. NEVER put water on a metal fire. This can cause a HUGE EXPLOSION ... operation. 16. Educate yourself beforehand and always be careful of your own and bystander safety.

Single point Cutting tool signature

Description : Single point Cutting tool signature

Last Answer : The shape of a tool is specified in a special sequence and this special sequence is called tool signature. The tool signature is given below (i) Back rake angle (ii) Side rake angle (iii) ... rake, end relief, side relief, end cutting edge, side cutting edge angle and 0.8 mm nose radius.

Explain with neat sketch the working principle of MIG.

Description : Explain with neat sketch the working principle of MIG.

Last Answer : In metal-arc inert gas welding the Weld area is shielded by an effectively inert atmosphere of argon, helium, carbon dioxide, or various other gas mixtures . The consumable bare Wire is fed automatically ... of the molten-weld puddle. Multiple-weld layers can be deposited at the joint. 

Compare between Hot rolling and Cold rolling.

Description : Compare between Hot rolling and Cold rolling.

Last Answer : Hot rolling Cold rolling  Metal is fed to the rolls after being heated above the recrytallization temperature. Metal is fed to the rolls when it is below the recrytallization temperature. ... Hot rolling is the father of the cold rolling. Cold rolling follows the hot rolling.

Explain any four properties of Moulding sand.

Description : Explain any four properties of Moulding sand. 

Last Answer : 1. Porosity: Molten metal always contain a certain amount of dissolved gases, which are evolved when the metal freezes the molten metal coming in contact with the moist sand , generates steam or ... to the casting. Refractoriness is measured by the sinter point of the sand rather than its melting

State the applications of TIG welding.

Description : State the applications of TIG welding.

Last Answer : The applications of TIG welding are as follows: 1. Mostly used to weld aluminum and aluminum alloys. 2. It is used to weld stainless steel, carbon base alloy, copper base alloy, nickel base alloy etc. 3. It is used to welding dissimilar metals. 4. It is mostly used in aerospace industries.

State the applications of rolling.

Description : State the applications of rolling.

Last Answer : Applications of rolling are as follows: 1. Concrete reinforcing bars. 2. Plates. 3. Wire rods. 4. Sheet and strip. 5. Rails. 6. Piping and tubes. 7. Body panels. 8. Construction materials

List any four casting defects.

Description : List any four casting defects.

Last Answer : The various types of casting defects are as follows: 1. Gas Porosity: Blowholes, open holes, pinholes. 2. Shrinkage defects: shrinkage cavity. 3. Mold material defects: Cut and washes, ... Pouring metal defects: Cold shut, misrun, slag inclusion. Metallurgical defects: Hot tears, hot spot.

List any four materials used for pattern making

Description : List any four materials used for pattern making

Last Answer : The various types of materials used are as follows: 1. Wood 2. Metal. 3. Plastic. 4. Plaster. 5. Wax.

Define Feed and speed in shaping machine

Description : Define Feed and speed in shaping machine

Last Answer : 1) Feed: Feed (S) is the relative movement of the work or tool in a direction perpendicular to the axis of reciprocation of the ram per double stroke. It is expressed in mm per stroke. 2) Speed: ... speed is the speed at which the metal is removed by the cutting tool in a period of one minute.

List any four accessories used on lathe.

Description : List any four accessories used on lathe.

Last Answer : The various accessories used in lathe are as follows. 1) Lathe centers 2) Carriers or driving dog 3) catch plates 4) Chucks 5) Face plates 6) Angle plates 7) Mandrels 8) Rests

List types of chips produced in machining process.

Description : List types of chips produced in machining process.

Last Answer : The various types of chips produced in machining process are as follows: 1. Continuous chips: According to its name, continuous chips have a continuous segment. . 2. Discontinuous chips or segmental chips: ... chip is same as the continuous chips except a built edge is form at the face of tool.

Now that Beverly Nelson has admitted to forging part of her evidence against Moore, does that change your view of her claims?

Description : Now that Beverly Nelson has admitted to forging part of her evidence against Moore, does that change your view of her claims?

Last Answer : No. Because her actions don’t negate the other women’s stories, nor do they call into question the ‘ban him from the mall’ contemporaneous rules that were put into place after his misbehavior. There’s plenty of evidence of Moore’s actions even if you take Nelson out of the picture. Nice try.

Which of the following process is not formative process? a.Bending b.Plastic injection molding c.Selective Laser Sintering d.Forging

Description : Which of the following process is not formative process? a.Bending b.Plastic injection molding c.Selective Laser Sintering d.Forging

Last Answer : c.Selective Laser Sintering

Can you get suspended or expelled for forging a teacher's note?

Description : Can you get suspended or expelled for forging a teacher's note?

Last Answer : A school can suspend or expel a student for any questionableact.Any regulations over this subject are set by the District SchoolBoard, not by any law.

Can you get suspended or expelled for forging a teacher's note?

Description : Can you get suspended or expelled for forging a teacher's note?

Last Answer : A school can suspend or expel a student for any questionableact.Any regulations over this subject are set by the District SchoolBoard, not by any law.

In drop forging process, the forging is done by dropping the __________ at high velocity. (A) Hammer (B) Workpiece (C) Die with hammer (D) Weight on hammer

Description : In drop forging process, the forging is done by dropping the __________ at high velocity. (A) Hammer (B) Workpiece (C) Die with hammer (D) Weight on hammer

Last Answer : (C) Die with hammer

Mild steel is used for making (A) Fish plates (B) Die block (C) Channels (D) Drop forging

Description : Mild steel is used for making (A) Fish plates (B) Die block (C) Channels (D) Drop forging

Last Answer : (C) Channels

Steel pipes are normally manufactured by __________ process. (A) Extrusion (B) Cold working (C) Forging (D) Electroforming

Description : Steel pipes are normally manufactured by __________ process. (A) Extrusion (B) Cold working (C) Forging (D) Electroforming

Last Answer : (A) Extrusion

Among casting, forging and forging which has the slowest rate of production? a) Casting b) Forging c) Machining d) All have equal rate of production

Description : Among casting, forging and forging which has the slowest rate of production? a) Casting b) Forging c) Machining d) All have equal rate of production

Last Answer : c) Machining

In forging, metal is in which of the following stage? a) Elastic b) Plastic c) Can be in any stage d) Rigid

Description : In forging, metal is in which of the following stage? a) Elastic b) Plastic c) Can be in any stage d) Rigid

Last Answer : b) Plastic

While designing a forging, the profile is selected such that the fibrous lines are parallel to the tensile forces and perpendicular to shear forces. a) True b) False

Description : While designing a forging, the profile is selected such that the fibrous lines are parallel to the tensile forces and perpendicular to shear forces. a) True b) False

Last Answer : a) True

Which process allows controlling grain structure of the product? a) Casting b) Forging c) None of the mentioned d) Die Casting

Description : Which process allows controlling grain structure of the product? a) Casting b) Forging c) None of the mentioned d) Die Casting

Last Answer : b) Forging

Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Description : Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Last Answer : (B) Cold rolling

A jet engine turbine blade is normally manufactured by (A) Forging (B) Shell moulding (C) Investment casting (D) Pressure die casting

Description : A jet engine turbine blade is normally manufactured by (A) Forging (B) Shell moulding (C) Investment casting (D) Pressure die casting

Last Answer : (C) Investment casting

Wrought iron is never shaped by (A) Casting (B) Cold working (C) Forging (D) Welding

Description : Wrought iron is never shaped by (A) Casting (B) Cold working (C) Forging (D) Welding

Last Answer : (A) Casting

The practice of forging a return address on an e‐mail so that the recipient is fooled into revealing private information is termed? a. hacking b. cracking c. dumpster diving d. spoofing

Description : The practice of forging a return address on an e‐mail so that the recipient is fooled into revealing private information is termed? a. hacking b. cracking c. dumpster diving d. spoofing

Last Answer : d. spoofing

Draw flatter and Fuller. State its use in forging.

Description : Draw flatter and Fuller. State its use in forging.

Last Answer : 1. Fuller: Use of Fuller: Fuller is a forging tool, used to spread the metal. The fuller is placed against the metal stock, and then either the fuller or the stock is struck ... are used to give smoothness and accuracy to articles which have already been shaped by fullers and swages. 

Define forging.

Description : Define forging.

Last Answer : Definition of Forging: Forging can be defined as the controlled plastic deformation of metals at elevated temperatures in to a predetermined size or shape using compressive forces exerted, through some type ... & shaping it in dies under the pressure of heavy hammers, forging machines & presses.

Explain drop forging with neat sketch.

Description : Explain drop forging with neat sketch. 

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... [5] This energy will be delivered to the metal work-piece to produce plastic deformation.  

Describe briefly, hand forging and machine forging.

Description : Describe briefly, hand forging and machine forging. 

Last Answer : Hand Forging: [1] Hand forging is the oldest type of metal working process and has influenced the formation of other materials through the age. [2] Smith forging was formerly the process ... the height from which they fall, the higher will be intensity of blow the hammer will provide.

Write forging sequence for spanners.

Description : Write forging sequence for spanners.

Last Answer : Forging Sequence for Spanner: (1) The heated stock is elongated by reducing its cross section in first die. The operation is known as Fullering . (2) The metal is redistributed, increasing the cross ... . (5) Flash is removed. (6) Heat treatment and machining is done as per requirement. 

List any four applications of forging process.

Description : List any four applications of forging process. 

Last Answer : Applications of Forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Spanner 5. Alloy wheel 6. Differential gears 7. Drive shafts 8. Clutch hubs 9. Universal joints 10. Hand Tools

State any two advantages of forging process.

Description : State any two advantages of forging process. 

Last Answer : Advantages of forging processes: 1) Complex shaped parts can be forged 2) Mass production with greater accuracy is achieved. 3) It is very easy to maintain close tolerances. 4) ... highly skilled operator. 6) Better reproducibility. 7) Machining is not necessary to obtain final shape 

Classify forging. State Fullering

Description : Classify forging. State Fullering

Last Answer : Answer: Classification of forging processes 1.Open die forging: a) Hand forging b) Power forging: i. Hammer forging ii. Press forging 2.Close die forging: a) Drop forging b) ... The force is applied on the top fuller which results in decreasing the cross section at that point.  

Describe forging sequence for crank shaft.

Description : Describe forging sequence for crank shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging.   [2] After preliminary roll forging, stock ... the finished part is then trimmed in blanking die to remove excess metal or flash.   

Explain drop forging

Description : Explain drop forging

Last Answer : Drop Forging Process: Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop hammer. Anvil of drop forging hammer is attached to the frame ... 5] This energy will be delivered to the metal work-piece to produce plastic deformation.