Name one gaseous and one liquid electrical insulation material.

Name one gaseous and one liquid electrical insulation material. 
by

1 Answer

Answer :

i) Gaseous insulating material :

1. Air

2. Nitrogen

3. Hydrogen

4. SF6

ii) liquid insulating material:

1. Transformer oil

2. Capacitor oil

3. Cable oil

4. Pyranol

5. Savotal

6. Savol

7. Vegetable oil

8. Silicon liquids 
by

Related questions

Write any two properties of good electrical insulation material.

Description : Write any two properties of good electrical insulation material. 

Last Answer : Electrical Properties of insulating material:-  1. It should have high resistance. 2. It should have high breakdown voltage. 3. It should have high dielectric strength. 4. It should have low dielectric loss. 5. It should have low dielectric constant. 

Explain the reasons for failure of gaseous and solid dielectric materials used in electrical engineering application.

Description : Explain the reasons for failure of gaseous and solid dielectric materials used in electrical engineering application. 

Last Answer : Reasons for failure of gaseous and solid dielectric materials used in electrical engineering application. 1. If the system voltage increases more than breakdown voltage for some interval then ... chemical breakdown usually occurs at very high temperature and high humidity of the surrounding air 

State any two applications of gaseous insulating material used in switchgears.

Description : State any two applications of gaseous insulating material used in switchgears. 

Last Answer : Applications of gaseous insulating material used in switchgears:   1. Non inflammable material (gas) in switchgear. 2. High dielectrical strength material in electrical machine. 3. As a cooling agent in circuit breaker

Define dielectric failure of electrical insulating material.

Description : Define dielectric failure of electrical insulating material. 

Last Answer : Definition of dielectric failure of electrical insulating material. In the insulating material if the applied voltage is increased gradually then for certain value insulation will break down, ... material vanishes its insulating properties and starts conducting, also known as dielectric failure.

List any four applications of insulting material used in electrical fields.

Description : List any four applications of insulting material used in electrical fields. 

Last Answer : Applications of insulting material used in electrical fields: 1. In Electrical machines 2. In electrical transformers. 3. Transformer bushing 4. Insulators 5. Domestic equipment’s ( or any other equivalent applications) 6. Insulation on wires and cables 

Electrical Materials and Wiring Practice

Description : Electrical Materials and Wiring Practice

Last Answer : Unit 1. Wiring components, tools and safety devices 1a. Explain safety rules/ standards in the given electrical systems. 1b. Describe the use of the given tools in the given electrical ... installations as per IE rules.  5.4 Significance and adverse effects of improper earthing systems

Explain the criteria to be applied in deciding the earthing system for an electrical installation.

Description : Explain the criteria to be applied in deciding the earthing system for an electrical installation. 

Last Answer : Following criteria (factors) to be applied in deciding the earthing system for an electrical installation: (1) Temperature of soil: (2) Soil Condition: * Different soil conditions give ... resistivity of earth, which is often the most significant factor 17) Cost of the earthing pit

Explain with justification two uses of each of two following as an electrical conductor: (i) Brass (ii) Silver

Description : Explain with justification two uses of each of two following as an electrical conductor: (i) Brass (ii) Silver 

Last Answer :  (i) Brass:  Brass is an alloy of copper (60% ) and zinc ( 40%) ; the proportions of zinc and copper can be varied to create a range of brasses with varying properties. Brasses set ... electrical conductor:  1) In switches to minimize contact resistance 2) In measuring instruments 3) In relays 

Explain the use of the following components in electrical wiring system and give specification of each: (i) MCB (ii) ELCB

Description : Explain the use of the following components in electrical wiring system and give specification of each: (i) MCB (ii) ELCB

Last Answer : i) MCB (Miniature Circuit Breaker)  * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with load and ELCB is ... The low sensitivity ELCB are used for electrical machine the rating is in between the 3A to 10 A

Explain the uses of safety rubber hand gloves and rubber mats in electrical engineering.

Description : Explain the uses of safety rubber hand gloves and rubber mats in electrical engineering. 

Last Answer : Uses of safety rubber hand gloves in electrical engineering:  * The safety rubber hand gloves are always used for online work to insulate the human body or operator from the electrical supply. * The ... human body) is isolated from ground or earth i.e. why danger of electrical shock is avoided. 

Explain the use of following tools in carrying out electrical wiring installation: (i) Nose pliers (ii) Test lamps (iii) Crimping tools (iv) Cutter.

Description : Explain the use of following tools in carrying out electrical wiring installation: (i) Nose pliers (ii) Test lamps (iii) Crimping tools (iv) Cutter. 

Last Answer : (i) Nose pliers : To hold and tight the wires (ii) Test lamps: Verification of voltage & current in the system and also check the open circuit (iii) Crimping tools: for crimping of the lugs for wires and cables (iv) Cutter: To cut the wire and remove the insulation 

Define earthing related to electrical wiring system.

Description : Define earthing related to electrical wiring system. 

Last Answer : Definition of earthing:  * Earthing means connecting the metal body of electrical device to the general mass of earth by a wire of negligible resistance. OR * Earthing means connecting ... Earthing is the processes of connection to the specific part of installation with earth conductive surface.

State the need for strictly following safety rules while working in electrical installations.

Description : State the need for strictly following safety rules while working in electrical installations. 

Last Answer : Need for strictly following safety rules while working in electrical installations: 1. To avoid the electrical shock to the human being and to provide safe guard. 2. To minimize the chances ... of the electrical devices. 5. To minimize the chances of mechanical and electrical accidents. 

State any two electrical, mechanical and thermal properties of insulating materials.

Description : State any two electrical, mechanical and thermal properties of insulating materials. 

Last Answer : i) Electrical Properties of insulating material:- 1. It should have high resistance. 2. It should have high breakdown voltage. 3. It should have high dielectric strength. 4. It should have low ... . 4. Ii should have thermal Stability. 5. Co-efficient of thermal expansion should be low.

State any four IE Rules to be followed in respect of safety while working on electrical installation system.

Description : State any four IE Rules to be followed in respect of safety while working on electrical installation system.  

Last Answer : While working in an electrical installation following safety IE rules regarding with safety: 1. IE Rule 3 : Authorization 2. IE Rule 29 : Construction and maintenance of electrical supply line and apparatus ... . IE Rule 60: Test for resistance of insulation 27. IE Rule 61: Connection with earth 

Enlist types of electrical wiring systems. Explain casing and capping type wiring system.

Description : Enlist types of electrical wiring systems. Explain casing and capping type wiring system.

Last Answer : List the types of Internal wiring in residential installations - 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping ... less chances of mechanical injury. Future expansion is possible and repairing and maintenance is easily possible. 

Explain the suitability of copper as an electrical conductor with reference to its mechanical and electrical properties.

Description : Explain the suitability of copper as an electrical conductor with reference to its mechanical and electrical properties. 

Last Answer : Following are properties of conductor:-  i) High conductivity :-  Material should have high conductivity, So that * Cross section of conductor (size) reduces, * Copper losses reduces, * So Efficiency ... ; less costly. ix) Scrap Value:-  Material should have high scrap value. 

Electrical insulation is classed by the _____________. A. International Association of Electrical Manufacturers B. approximate operating voltage and current expected C. U.S. Coast Guard D. temperature stability of the manufacturing material(s)

Description : Electrical insulation is classed by the _____________. A. International Association of Electrical Manufacturers B. approximate operating voltage and current expected C. U.S. Coast Guard D. temperature stability of the manufacturing material(s)

Last Answer : Answer: D

Polystyrene is a light, transparent, thermoplastic material used for making (A) Toys and combs (B) Packaging bags (C) Non-sticking utensils (D) Electrical insulation

Description : Polystyrene is a light, transparent, thermoplastic material used for making (A) Toys and combs (B) Packaging bags (C) Non-sticking utensils (D) Electrical insulation

Last Answer : (A) Toys and combs

State gaseous and liquid insulating material.

Description : State gaseous and liquid insulating material.

Last Answer : i) Gaseous insulating material : 1. Air 2. Nitrogen 3. Hydrogen 4. SF6 ii) liquid insulating material: 1. Transformer oil 2. Capacitor oil 3. Cable oil 4. Pyranol 5. Savotal 6. Savol 7. Vegetable oil 8. Silicon liquids

State the causes of deterioration of liquid and solid dielectrics.

Description : State the causes of deterioration of liquid and solid dielectrics. 

Last Answer : The causes of deterioration of liquid and solid dielectrics:  1. Voltage rating 2. Humidity in atmosphere or moisture content.  3. Temperature of the oil and solid dielectric material 4. Due ... cable joints and connection. 5. Increasing in supply frequency. 6. Due to unbalanced load.

State any two applications of: (i) Ferromagnetic (ii) Paramagnetic material.

Description : State any two applications of: (i) Ferromagnetic (ii) Paramagnetic material. 

Last Answer : Applications of Ferromagnetic Materials:  1. In the transformer laminations. 2. In Electrical machines as a magnetic material. 3. In Magnetic poles of motor and generator 4. Magnetic ... : 1. Solid state MASER  2. Using adiabatic demagnetization low temperature can be achieved. 

Would you expect the insulation around an electrical outlet to be made of a metal nonmetal or metalloid?

Description : Would you expect the insulation around an electrical outlet to be made of a metal nonmetal or metalloid?

Last Answer : Need answer

Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should never be grounded. C. Electrical cables must be rigidly held in place by welding of armored cable, or glued in place where nonmetallic insulation is used. D. All of the above.

Description : Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should ... , or glued in place where nonmetallic insulation is used. D. All of the above.

Last Answer : Answer: A

The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength of the insulation B. the paint dust is composed of abrasive and semi-conducting materials which impair insulation C. paint dust buildup has a tendency to cause corrosion D. phase windings frequently become isolated from each other due to dust interference at the terminals

Description : The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength ... phase windings frequently become isolated from each other due to dust interference at the terminals

Last Answer : Answer: B

Electrical failures in motors are caused by the breakdown of insulation, which may be caused by _____________. A. penetration of moisture B. accumulation of dirt C. overheating D. all of the above

Description : Electrical failures in motors are caused by the breakdown of insulation, which may be caused by _____________. A. penetration of moisture B. accumulation of dirt C. overheating D. all of the above

Last Answer : Answer: D

As part of a routine maintenance program for deck machinery, you should ___________. A. inspect electrical wiring and pushbutton switches for evidence of corrosion or burned insulation B. disassemble pushbutton switches and drain water each week C. remove motor covers and ventilate as weather permits D. Check drum switch contact pressure every three months

Description : As part of a routine maintenance program for deck machinery, you should ___________. A. inspect electrical wiring and pushbutton switches for evidence of corrosion or burned insulation B. disassemble ... covers and ventilate as weather permits D. Check drum switch contact pressure every three months

Last Answer : Answer: A

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Last Answer : Answer: A

If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform a 'high pot' test to determine the condition of the insulation C. water wash the motor and controller to remove any salt that may interfere with smooth operation D. check run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Description : If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform ... run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Last Answer : Answer: D

Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the condition of the bearings C. provide for the correct proper tightening of the field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Description : Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the ... field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Last Answer : Answer: B

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the machine secured B. millivolt meter and a jumper with the machine running C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the ... C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Last Answer : Answer: B

The greatest single cause of electrical failures is ______. A. the breakdown of insulation B. overcurrent C. high inductance D. too frequent testing

Description : The greatest single cause of electrical failures is ______. A. the breakdown of insulation B. overcurrent C. high inductance D. too frequent testing

Last Answer : Answer: A

Accidental grounds in a shipboard electrical system must be repaired as soon as possible as they will ____________. A. result in immediate power outages B. damage circuit breakers C. appear on the ground detection system D. damage insulation and may cause outages

Description : Accidental grounds in a shipboard electrical system must be repaired as soon as possible as they will ____________. A. result in immediate power outages B. damage circuit breakers C. appear on the ground detection system D. damage insulation and may cause outages

Last Answer : Answer: D

When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment away. B. Measure capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Description : When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment ... capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Last Answer : Answer: C

Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Description : Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Last Answer : Answer: D

A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Description : A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Last Answer : Answer: C

Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. lowers the insulation value and is a common cause of fault grounds in idle machines C. will enhance insulation resistance only if it is fresh water and contains no salt D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Description : Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. ... D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Last Answer : Answer: B

Which of the listed groups of electrical insulation materials is best suited for the highest operating temperatures? A. impregnated cotton and silk B. unimpregnated paper and cotton C. pure glass and quartz D. mica and porcelain with bonding agents

Description : Which of the listed groups of electrical insulation materials is best suited for the highest operating temperatures? A. impregnated cotton and silk B. unimpregnated paper and cotton C. pure glass and quartz D. mica and porcelain with bonding agents

Last Answer : Answer: C

Which of the listed classes of electrical insulation is suited for the highest operating temperature? A. Class 90 (O) B. Class 105 (A) C. Class 130 (B) D. Class 180 (H)

Description : Which of the listed classes of electrical insulation is suited for the highest operating temperature? A. Class 90 (O) B. Class 105 (A) C. Class 130 (B) D. Class 180 (H)

Last Answer : Answer: D

The life expectancy of electrical insulation, is approximately halved for an increased operating temperature of _______________. A. 10°C B. 25°C C. 50°C D. 100°C

Description : The life expectancy of electrical insulation, is approximately halved for an increased operating temperature of _______________. A. 10°C B. 25°C C. 50°C D. 100°C

Last Answer : Answer: A

The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens useful life C. energy is wasted if full loading is not utilized D. power factor correction methods are load dependent

Description : The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens ... wasted if full loading is not utilized D. power factor correction methods are load dependent

Last Answer : Answer: B

Electrical machinery insulation will break down more rapidly due to _________________. A. low loading of motors and generators B. frequent megger testing C. high temperatures and vibration D. high operating frequencies

Description : Electrical machinery insulation will break down more rapidly due to _________________. A. low loading of motors and generators B. frequent megger testing C. high temperatures and vibration D. high operating frequencies

Last Answer : Answer: C

Cleaning of electrical insulation should be _____________. A. done every six months B. accomplished every 12 months C. determined by need and not the calendar D. performed whenever the electrician is not otherwise busy

Description : Cleaning of electrical insulation should be _____________. A. done every six months B. accomplished every 12 months C. determined by need and not the calendar D. performed whenever the electrician is not otherwise busy

Last Answer : Answer: C

Part of the insulation of practically all electrical machinery is in the form of organic compounds which contain some amount of ______________. A. asbestos B. water C. fibre D. plastic

Description : Part of the insulation of practically all electrical machinery is in the form of organic compounds which contain some amount of ______________. A. asbestos B. water C. fibre D. plastic

Last Answer : Answer: B

When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Description : When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Last Answer : Answer: B

Copper is often used as an electrical conductor because it _______________. A. has high resistance at low temperatures B. has a highly polished surface C. is able to pass current with little opposition D. holds insulation together well

Description : Copper is often used as an electrical conductor because it _______________. A. has high resistance at low temperatures B. has a highly polished surface C. is able to pass current with little opposition D. holds insulation together well

Last Answer : Answer: C

An insulation resistance test is performed on a particular piece of electric equipment. In addition to the resistance reading, what information listed below should be entered in the electrical log? A. The maximum allowable operating temperature of the machine. B. The temperature of the machine at the time the resistance reading was taken. C. The normal temperature rise of the machine. D. The complete nameplate data from the resistance test instrument used to obtain the reading.

Description : An insulation resistance test is performed on a particular piece of electric equipment. In addition to the resistance reading, what information listed below should be entered in the electrical log? A. ... D. The complete nameplate data from the resistance test instrument used to obtain the reading.

Last Answer : Answer: B

Electrical leads and insulation on a motor should be painted with ____________. A. heat-resisting acrylic B. heat-resisting aluminum C. insulating varnish D. insulating white lead

Description : Electrical leads and insulation on a motor should be painted with ____________. A. heat-resisting acrylic B. heat-resisting aluminum C. insulating varnish D. insulating white lead

Last Answer : Answer: C

The greatest detrimental effect on idle electrical equipment, such as cargo pump motors, is the _____________. A. loss of residual magnetism B. absorption of moisture in the insulation C. insulation varnish flaking D. dirt collecting on the windings

Description : The greatest detrimental effect on idle electrical equipment, such as cargo pump motors, is the _____________. A. loss of residual magnetism B. absorption of moisture in the insulation C. insulation varnish flaking D. dirt collecting on the windings

Last Answer : Answer: B

Grounds occurring in electrical machinery as a result of insulation failure may result from _____________. A. deterioration through extended use B. excessive heat C. extended periods of vibration D. all of the above

Description : Grounds occurring in electrical machinery as a result of insulation failure may result from _____________. A. deterioration through extended use B. excessive heat C. extended periods of vibration D. all of the above

Last Answer : Answer: D