Heat transfer co-efficient (h1 ) for liquids increases with (A) Increasing temperature (B) Decreasing temperature (C) Decreasing Reynolds number (D) None of these

Heat transfer co-efficient (h1

) for liquids increases with

(A) Increasing temperature

(B) Decreasing temperature

(C) Decreasing Reynolds number

(D) None of these


by

1 Answer

Answer :

(A) Increasing temperature

by

Related questions

The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Description : The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Last Answer : (A) Increasing temperature of the vapour

If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Last Answer : (B) Always between h1 and h2

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient varies with the pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Description : The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient ... pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Last Answer : (B) D-0.2

Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Description : Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Last Answer : (D) Reynolds number for the flow involved is < 2100

The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient(B) Increasing the liquid film co-efficient(C) Increasing the total pressure(D) Decreasing the total pressure

Description : The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient (B) Increasing the liquid film co-efficient (C) Increasing the total pressure (D) Decreasing the total pressure

Last Answer : (A) Increasing the gas film co-efficient

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Description : Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Last Answer : Option A

The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is(A) 100(B) 10(C) 5(D) 1.

Description : The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is. (A) 100 (B) 10 (C) 5 (D) 1

Last Answer : (B) 10

The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Description : The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Last Answer : (D) Dependent on the Reynolds number

As the difference between the wall temperature and bulk temperature increases, the boiling heat transfer co-efficient (A) Continues to increase (B) Continues to decrease (C) Goes through a minimum (D) Goes through a maximum

Description : As the difference between the wall temperature and bulk temperature increases, the boiling heat transfer co-efficient (A) Continues to increase (B) Continues to decrease (C) Goes through a minimum (D) Goes through a maximum

Last Answer : (C) Goes through a minimum

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

The co-efficient of drag and lift for an incompressible fluid depends on the (A) Reynolds number (B) Froude number (C) Mach number (D) All (A), (B) and (C)

Description : The co-efficient of drag and lift for an incompressible fluid depends on the (A) Reynolds number (B) Froude number (C) Mach number (D) All (A), (B) and (C)

Last Answer : (A) Reynolds numbe

The discharge co-efficient for an orifice meter does not depend upon the (A) Pipe length (B) Ratio of pipe diameter to orifice diameter (C) Type of orifice & the Reynolds number (D) Pipe diameter

Description : The discharge co-efficient for an orifice meter does not depend upon the (A) Pipe length (B) Ratio of pipe diameter to orifice diameter (C) Type of orifice & the Reynolds number (D) Pipe diameter

Last Answer : (A) Pipe length

In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said to have the same hydraulic roughness, when they have equal values of (A) Relative roughness (B) Absolute roughness (C) Friction co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Last Answer : (C) Friction co-efficient for flows at equal Reynold number

The co-efficient of discharge of an orificemeter is a function of (A) Reynolds number at the orifice (B) Ratio of orifice dia to pipe dia (C) Both (A) and (B) (D) None of the above parameters, and has a constant value of 0.61

Description : The co-efficient of discharge of an orificemeter is a function of (A) Reynolds number at the orifice (B) Ratio of orifice dia to pipe dia (C) Both (A) and (B) (D) None of the above parameters, and has a constant value of 0.61

Last Answer : (C) Both (A) and (B)

An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Description : An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Last Answer : (D) Be free from radiation damage and non-corrosive

Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Description : Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Last Answer : (D) None of these

The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the right face is 10 W/m2 .K. At steady state, the temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Description : The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the ... temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Last Answer : (D) 48.7

The main purpose of providing fins on heat transfer surface is to increase the (A) Temperature gradient (B) Mechanical strength of the equipment (C) Heat transfer area (D) Heat transfer co-efficient

Description : The main purpose of providing fins on heat transfer surface is to increase the (A) Temperature gradient (B) Mechanical strength of the equipment (C) Heat transfer area (D) Heat transfer co-efficient

Last Answer : (C) Heat transfer area

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

In a shell and tube heat exchanger, floating head is used for (A) Large temperature differentials (B) High heat transfer co-efficient (C) Low pressure drop (D) Less corrosion of tubes

Description : In a shell and tube heat exchanger, floating head is used for (A) Large temperature differentials (B) High heat transfer co-efficient (C) Low pressure drop (D) Less corrosion of tubes

Last Answer : (A) Large temperature differentials

Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is ‘3k/l’. If the wall temperature on the outside is held at 25°C, what is the inside wall temperature in degree centigrade?(A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Description : Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is 3k/l'. If the wall temperature ... wall temperature in degree centigrade? (A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Last Answer : (C) 81.25

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number(A) Increases(B) Decreases(C) Remain same(D) May increase or decrease.

Description : The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number. (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease

Last Answer : (B) Decreases

The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Description : The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Last Answer : (B) 4 0.8

Nusselt number/Biot number varies (A) Inversely with thermal conductivity (B) Directly with heat transfer co-efficient (C) Directly with thermal conductivity (D) Inversely with the dimension of the solid

Description : Nusselt number/Biot number varies (A) Inversely with thermal conductivity (B) Directly with heat transfer co-efficient (C) Directly with thermal conductivity (D) Inversely with the dimension of the solid

Last Answer : (A) Inversely with thermal conductivity

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Increasing the liquor level in the evaporator results in the (A) Decreased capacity (B) Increase in liquor film co-efficient (C) Decreased effect of hydrostatic head (D) Increased true temperature drop

Description : Increasing the liquor level in the evaporator results in the (A) Decreased capacity (B) Increase in liquor film co-efficient (C) Decreased effect of hydrostatic head (D) Increased true temperature drop

Last Answer : (A) Decreased capacity

Critical solution temperature (or the con-solute temperature) for partially miscible liquids (e.g., phenol-water) is the minimum temperature at which (A) A homogeneous solution (say of phenol water) is formed (B) Mutual solubility of the two liquids shows a decreasing trend (C) Two liquids are completely separated into two layers (D) None of these

Description : Critical solution temperature (or the con-solute temperature) for partially miscible liquids (e.g., phenol-water) is the minimum temperature at which (A) A homogeneous solution (say of phenol water) is ... a decreasing trend (C) Two liquids are completely separated into two layers (D) None of these

Last Answer : (A) A homogeneous solution (say of phenol water) is formed

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

. In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Description : . In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Last Answer : (A) Infinity

Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Description : Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Last Answer : (B) Requirement of heat transfer area is low

Heat transfer by natural convection is enhanced in system with (A) High viscosity (B) High co-efficient of thermal expansio

Description : Heat transfer by natural convection is enhanced in system with (A) High viscosity (B) High co-efficient of thermal expansio

Last Answer : (B) High co-efficient of thermal expansion

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

The unit of heat transfer co-efficient in SI unit is (A) J/M2°K (B) W/m2°K (C) W/m°K (D) J/m°K

Description : The unit of heat transfer co-efficient in SI unit is (A) J/M2°K (B) W/m2°K (C) W/m°K (D) J/m°K

Last Answer : (B) W/m2°K

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is (A) Vertical heat exchanger with steam on tube side (B) Vertical heat exchanger with steam on shell side (C) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Description : Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient ... ) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Last Answer : (B) Vertical heat exchanger with steam on shell side

Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer. (A) No (B) The least (C) The largest (D) Lower

Description : Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer. (A) No (B) The least (C) The largest (D) Lower

Last Answer : (C) The largest

Steam side heat transfer co-efficient in an evaporator is in the range of __________ kcal/hr.m2°C. (A) 10-50 (B) 100-500 (C) 1000-1500 (D) 5000-15000

Description : Steam side heat transfer co-efficient in an evaporator is in the range of __________ kcal/hr.m2°C. (A) 10-50 (B) 100-500 (C) 1000-1500 (D) 5000-15000

Last Answer : (D) 5000-15000

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

Description : For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

Last Answer : (C) 6.1

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Description : Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Last Answer : (D) > 10000

Heat exchangers operating, when the asymptotic range is reached, (A) Provide very large heat transfer co-efficient (B) Results in making part of the heating surface inactive (C) Results in abruptly increased velocity (D) None of these

Description : Heat exchangers operating, when the asymptotic range is reached, (A) Provide very large heat transfer co-efficient (B) Results in making part of the heating surface inactive (C) Results in abruptly increased velocity (D) None of these

Last Answer : (B) Results in making part of the heating surface inactive