Mass transfer rate between two fluid phases does not necessarily depend on the __________ of the two phases. (A) Chemical properties (B) Physical properties (C) Degree of turbulence (D) Interfacial area

Mass transfer rate between two fluid phases does not necessarily
depend on the __________ of the two phases.
(A) Chemical properties
(B) Physical properties
(C) Degree of turbulence
(D) Interfacial area
by

1 Answer

Answer :

(A) Chemical properties
by

Related questions

The rate of mass transfer is not dependent upon the (A) Degree of dispersion of one fluid in the other (B) Interfacial surface exposed between the phases (C) Both (A) & (B) (D) None of these

Description : The rate of mass transfer is not dependent upon the (A) Degree of dispersion of one fluid in the other (B) Interfacial surface exposed between the phases (C) Both (A) & (B) (D) None of these

Last Answer : (D) None of these

Measurement of the interfacial area of mass transfer is achieved easily & accurately in case of a __________ column. (A) Spray (B) Packed (C) Bubble cap plate (D) Wetted wall

Description : Measurement of the interfacial area of mass transfer is achieved easily & accurately in case of a __________ column. (A) Spray (B) Packed (C) Bubble cap plate (D) Wetted wall

Last Answer : (D) Wetted wall

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

Use of transverse baffles in a shell and tube heat exchanger is done to increase the (A) Rate of heat transfer (B) Flow velocity (C) Turbulence of shell side fluid (D) All (A), (B) and (C)

Description : Use of transverse baffles in a shell and tube heat exchanger is done to increase the (A) Rate of heat transfer (B) Flow velocity (C) Turbulence of shell side fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Crystal size in a continuous crystalliser depends upon the (A) Rate of heat transfer (B) Degree of turbulence (C) Degree of super-saturation (D) All (A), (B) and (C)

Description : Crystal size in a continuous crystalliser depends upon the (A) Rate of heat transfer (B) Degree of turbulence (C) Degree of super-saturation (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

To get high tray efficiency (A) Interfacial surface between liquid and gas phase should be large (B) Time of contact between the two phases should be less (C) Gas velocity should be very low (D) Liquid entrainment should be severe

Description : To get high tray efficiency (A) Interfacial surface between liquid and gas phase should be large (B) Time of contact between the two phases should be less (C) Gas velocity should be very low (D) Liquid entrainment should be severe

Last Answer : (A) Interfacial surface between liquid and gas phase should be large

Weeping in a distillation column (A) Increases tray efficiency (B) Provides large interfacial surface for mass transfer (C) Results due to very high gas velocity (D) Results due to very low gas velocity

Description : Weeping in a distillation column (A) Increases tray efficiency (B) Provides large interfacial surface for mass transfer (C) Results due to very high gas velocity (D) Results due to very low gas velocity

Last Answer : (D) Results due to very low gas velocity

The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of the following resistance (s) is (are) controlling? (A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Description : The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of ... A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Last Answer : (B) Gas side

In an interphase heat transfer process, the equilibrium state corresponds to equality of temperature in the two phases, while the condition for equilibrium in an interphase mass transfer process is equality of (A) Concentrations (B) Chemical potentials (C) Activity co-efficients (D) Mass transfer co-efficients

Description : In an interphase heat transfer process, the equilibrium state corresponds to equality of temperature in the two phases, while the condition for equilibrium in an interphase mass transfer process is ... B) Chemical potentials (C) Activity co-efficients (D) Mass transfer co-efficients

Last Answer : (A) Concentrations

Extensive properties of a thermodynamic system depend upon the __________ of the system. (A) Specific volume (B) Temperature (C) Mass (D) Pressure

Description : Extensive properties of a thermodynamic system depend upon the __________ of the system. (A) Specific volume (B) Temperature (C) Mass (D) Pressure

Last Answer : (C) Mass

Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Description : Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Last Answer : A) Pipe length

Overall rate of reaction in a heterogeneous catalytic reaction depends upon the mass and energy transfer from the fluid to solid surface and its rate of reaction is usually __________ the concentration of catalyst, if it doesnot entail a chain mechanism.(A) Proportional to(B) Independent of(C) Inversely proportional to(D) Proportional to the square o

Description : Overall rate of reaction in a heterogeneous catalytic reaction depends upon the mass and energy transfer from the fluid to solid surface and its rate of reaction is usually __________ the concentration of ... to (B) Independent of (C) Inversely proportional to (D) Proportional to the square o

Last Answer : (A) Proportional to

Filtration rate does not depend upon the (A) Pressure drop & area of filtering surface (B) Resistance of the cake & the septum (C) Properties of the cake & the filtrate (D) None of these

Description : Filtration rate does not depend upon the (A) Pressure drop & area of filtering surface (B) Resistance of the cake & the septum (C) Properties of the cake & the filtrate (D) None of these

Last Answer : (D) None of these

What causes convective acceleration in fluid flow? (A) Steep slope in flow (B) Unsteady nature of flow (C) Non-uniformity of flow (D) Turbulence in flow

Description : What causes convective acceleration in fluid flow? (A) Steep slope in flow (B) Unsteady nature of flow (C) Non-uniformity of flow (D) Turbulence in flow

Last Answer : (C) Non-uniformity of flow

. Pick out the wrong statement. (A) The eddy viscosity is a function of(B) The eddy viscosity is a fluid property(C) The viscosity of gas increases with increase in temperature(D) The viscosity of a liquid increases with decrease in temperature the type of turbulence involved

Description : . Pick out the wrong statement. (A) The eddy viscosity is a function of the type of turbulence involved (B) The eddy viscosity is a fluid property (C) The viscosity of gas increases with increase in temperature (D) The viscosity of a liquid increases with decrease in temperature

Last Answer : (B) The eddy viscosity is a fluid property

Which of the following is the most controlling factor for the rate of bubble detachment from the hot solid surface? (A) Liquid density (B) Liquid viscosity (C) Hot surface temperature (D) Interfacial tension

Description : Which of the following is the most controlling factor for the rate of bubble detachment from the hot solid surface? (A) Liquid density (B) Liquid viscosity (C) Hot surface temperature (D) Interfacial tension

Last Answer : (D) Interfacial tension

Heat transfer by __________ may not necessarily require the presence of a medium. (A) Conduction (B) Natural convection (C) Forced convection (D) Radiation

Description : Heat transfer by __________ may not necessarily require the presence of a medium. (A) Conduction (B) Natural convection (C) Forced convection (D) Radiation

Last Answer : (D) Radiation

Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Description : Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Last Answer : (D) None of these

The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800

Description : The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800

Last Answer : (A) 500

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

Hydrogen differs from deuterium in __________ properties. (A) Radioactive (B) Physical (C) Chemical (D) All (A), (B) and (C

Description : Hydrogen differs from deuterium in __________ properties. (A) Radioactive (B) Physical (C) Chemical (D) All (A), (B) and (C

Last Answer : (B) Physical

Drag force acting on a body does not depend upon the (A) Density of the fluid (B) Density of the body (C) Velocity of the body (D) Projected area of the body

Description : Drag force acting on a body does not depend upon the (A) Density of the fluid (B) Density of the body (C) Velocity of the body (D) Projected area of the body

Last Answer : (B) Density of the body

The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Description : The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Last Answer : (A) Area of surface in contact

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

Metalloids (A) Are good conductor of heat & electricity (B) Act as electron donors with metals & as electron acceptor with non metals (C) Are not necessarily solids at room temperature (D) Are compounds that exhibit both metallic & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

Description : Metalloids (A) Are good conductor of heat & electricity (B) Act as electron donors with metals & as electron acceptor with non metals (C) Are not necessarily solids at room temperature ... & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

Last Answer : D) Are compounds that exhibit both metallic & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Description : Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Last Answer : (A) Type of fuels viz. solid, liquid or gaseous

Heat transfer rate to the stock/charge in the furnace does not depend upon the(A) Emissivity of the refractory walls(B) Size of the furnace(C) Use of waste heat recovery equipments(D) Thickness of the stock

Description : Heat transfer rate to the stock/charge in the furnace does not depend upon the (A) Emissivity of the refractory walls (B) Size of the furnace (C) Use of waste heat recovery equipments (D) Thickness of the stock

Last Answer : (C) Use of waste heat recovery equipments

The McCabe ΔL law states that the (A) Molar heats of vaporisation of components are nearly equal (B) Linear crystal growth rate depends on the degree of super-saturation (C) Linear crystal growth rate does not depend on the crystal size (D) Linear crystal growth rate depends on the crystal size

Description : The McCabe ΔL law states that the (A) Molar heats of vaporisation of components are nearly equal (B) Linear crystal growth rate depends on the degree of super-saturation (C) Linear ... does not depend on the crystal size (D) Linear crystal growth rate depends on the crystal size

Last Answer : (C) Linear crystal growth rate does not depend on the crystal size

In isotropic turbulence, the __________ are equal to each other. (A) Temporal velocity components (B) Mean square of velocity fluctuations in the three co-ordinate directions (C) Root mean square of velocity fluctuations in the three co-ordinate directions (D) None of these

Description : In isotropic turbulence, the __________ are equal to each other. (A) Temporal velocity components (B) Mean square of velocity fluctuations in the three co-ordinate directions (C) Root mean square of velocity fluctuations in the three co-ordinate directions (D) None of these

Last Answer : (B) Mean square of velocity fluctuations in the three co-ordinate directions

In a heat exchanger, the rate of heat transfer from the hot fluid to the cold fluid (A) Varies directly as the area and the LMTD (B) Directly proportional to LMTD and inversely proportional to the area (C) Varies as square of the area (D) None of these

Description : In a heat exchanger, the rate of heat transfer from the hot fluid to the cold fluid (A) Varies directly as the area and the LMTD (B) Directly proportional to LMTD and inversely proportional to the area (C) Varies as square of the area (D) None of these

Last Answer : (A) Varies directly as the area and the LMTD

For multi-component multiple phases to be in equilibrium at the same pressure and temperature, the __________ of each component must be same in all phases. (A) Chemical potential (B) Fugacity (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : For multi-component multiple phases to be in equilibrium at the same pressure and temperature, the __________ of each component must be same in all phases. (A) Chemical potential (B) Fugacity (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Radiation heat transfer rates does not depend upon the (A) Type of absorbing surface (B) Distance between the heat source and the object receiving the heat (C) Surface area and temperature of the heat source (D) None of these

Description : Radiation heat transfer rates does not depend upon the (A) Type of absorbing surface (B) Distance between the heat source and the object receiving the heat (C) Surface area and temperature of the heat source (D) None of these

Last Answer : (D) None of these

Fractional solvent extraction (A) Employs only one solvent (B) Employs two solvents (C) Results in low interfacial tension (D) None of these

Description : Fractional solvent extraction (A) Employs only one solvent (B) Employs two solvents (C) Results in low interfacial tension (D) None of these

Last Answer : (B) Employs two solvents

(3) preventing rapid setting of cement Explanation: Portland cement clinker is a hydraulic material which shall consist of at least two-thirds by mass of calcium silicates, the remainder consisting of aluminium- and ironcontaining clinker phases and other compounds. The ratio of CaO to SiO2 shall not be less than 2.0. The magnesium oxide content (MgO) shall not exceed 5.0% by mass. Cement sets when mixed with water by way of a complex series of chemical reactions still only partly understood.

Description : (3) preventing rapid setting of cement Explanation: Portland cement clinker is a hydraulic material which shall consist of at least two-thirds by mass of calcium silicates, the remainder consisting of ... mixed with water by way of a complex series of chemical reactions still only partly understood.

Last Answer : Milk is a colloidal system in which: (1) Water is dispersed in fat (2) Fat is dispersed in water (3) Fat and water are dispersed in each other (4) Fat is dissolved

If a system involves two phases, it is in ______ equilibrium when the mass of each phase reaches an equilibrium level and stays there.  A. Chemical  B. Thermal  C. Mechanical  D. Phase

Description : If a system involves two phases, it is in ______ equilibrium when the mass of each phase reaches an equilibrium level and stays there.  A. Chemical  B. Thermal  C. Mechanical  D. Phase

Last Answer : Phase

Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants; but it is afunction of reaction temperature. In a chemical reaction, the time requiredto reduce the concentration of reactant from 100 gm moles/litre to 50 gmmoles/litre is same as that required to reduce it from 2 gm moles/litre to 1gm mole/litre in the same volume. Then the order of this reaction is:(A) 0(B) 1(C) 2(D) 3

Description : Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants; but it is afunction of reaction temperature. In a chemical reaction, the time required to ... Then the order of this reaction is: (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (B) 1

Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability

Description : Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability

Last Answer : C) high thermal conductivity

Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Description : Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Binary distillation involves the mass transfer by __________ at the gas￾liquid interface. (A) Unidirectional diffusion from liquid to gas phase (B) Unidirectional diffusion from gas to liquid phase (C) Either 'a' or 'b' (D) A counter diffusion at an almost equal molar rate

Description : Binary distillation involves the mass transfer by __________ at the gas￾liquid interface. (A) Unidirectional diffusion from liquid to gas phase (B) Unidirectional diffusion from gas to liquid phase (C) Either 'a' or 'b' (D) A counter diffusion at an almost equal molar rate

Last Answer : (D) A counter diffusion at an almost equal molar rate

A packed tower compared to a plate tower for a particular mass transfer operation (A) Incurs smaller pressure drop (B) Allows installation of cooling coils (C) Is less costly when built in large sizes/diameters (D) Is more suitable, if suspended solids are present in fluid stream

Description : A packed tower compared to a plate tower for a particular mass transfer operation (A) Incurs smaller pressure drop (B) Allows installation of cooling coils (C) Is less costly when built in large sizes/diameters (D) Is more suitable, if suspended solids are present in fluid stream

Last Answer : (A) Incurs smaller pressure drop

In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/s (B) μ , α and θ all have units of m2/s (C) α and θ have units of m2/s, while μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Description : In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/ ... μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Last Answer : Option C

Location of vena-contracta in an orificemeter does not depend upon the (A) Type of orifice (B) Density, viscosity & compressibility of the fluid (C) Ratio of pipe diameter to orifice diameter (D) Pipe roughness

Description : Location of vena-contracta in an orificemeter does not depend upon the (A) Type of orifice (B) Density, viscosity & compressibility of the fluid (C) Ratio of pipe diameter to orifice diameter (D) Pipe roughness

Last Answer : (A) Type of orifice

Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Description : Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Last Answer : (A) Length of the pipe

The basic difference between vegetable oils and fats is in their (A) Density (B) Chemical properties (C) Physical state (D) Composition

Description : The basic difference between vegetable oils and fats is in their (A) Density (B) Chemical properties (C) Physical state (D) Composition

Last Answer : (C) Physical state

Vegetable oils and fats basically differ in their (A) Density ranges (B) Physical state (C) Chemical composition (D) Chemical properties

Description : Vegetable oils and fats basically differ in their (A) Density ranges (B) Physical state (C) Chemical composition (D) Chemical properties

Last Answer : (B) Physical state

What is the degree of freedom of an absorption process in which only one component is transferred between phases? (A) 1 (B) 2 (C) 3 (D) 4

Description : What is the degree of freedom of an absorption process in which only one component is transferred between phases? (A) 1 (B) 2 (C) 3 (D) 4

Last Answer : (C) 3