The rate of mass transfer is not dependent upon the (A) Degree of dispersion of one fluid in the other (B) Interfacial surface exposed between the phases (C) Both (A) & (B) (D) None of these

The rate of mass transfer is not dependent upon the
(A) Degree of dispersion of one fluid in the other
(B) Interfacial surface exposed between the phases
(C) Both (A) & (B)
(D) None of these
by

1 Answer

Answer :

(D) None of these
by

Related questions

Mass transfer rate between two fluid phases does not necessarily depend on the __________ of the two phases. (A) Chemical properties (B) Physical properties (C) Degree of turbulence (D) Interfacial area

Description : Mass transfer rate between two fluid phases does not necessarily depend on the __________ of the two phases. (A) Chemical properties (B) Physical properties (C) Degree of turbulence (D) Interfacial area

Last Answer : (A) Chemical properties

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

To get high tray efficiency (A) Interfacial surface between liquid and gas phase should be large (B) Time of contact between the two phases should be less (C) Gas velocity should be very low (D) Liquid entrainment should be severe

Description : To get high tray efficiency (A) Interfacial surface between liquid and gas phase should be large (B) Time of contact between the two phases should be less (C) Gas velocity should be very low (D) Liquid entrainment should be severe

Last Answer : (A) Interfacial surface between liquid and gas phase should be large

Weeping in a distillation column (A) Increases tray efficiency (B) Provides large interfacial surface for mass transfer (C) Results due to very high gas velocity (D) Results due to very low gas velocity

Description : Weeping in a distillation column (A) Increases tray efficiency (B) Provides large interfacial surface for mass transfer (C) Results due to very high gas velocity (D) Results due to very low gas velocity

Last Answer : (D) Results due to very low gas velocity

Measurement of the interfacial area of mass transfer is achieved easily & accurately in case of a __________ column. (A) Spray (B) Packed (C) Bubble cap plate (D) Wetted wall

Description : Measurement of the interfacial area of mass transfer is achieved easily & accurately in case of a __________ column. (A) Spray (B) Packed (C) Bubble cap plate (D) Wetted wall

Last Answer : (D) Wetted wall

Overall rate of reaction in a heterogeneous catalytic reaction depends upon the mass and energy transfer from the fluid to solid surface and its rate of reaction is usually __________ the concentration of catalyst, if it doesnot entail a chain mechanism.(A) Proportional to(B) Independent of(C) Inversely proportional to(D) Proportional to the square o

Description : Overall rate of reaction in a heterogeneous catalytic reaction depends upon the mass and energy transfer from the fluid to solid surface and its rate of reaction is usually __________ the concentration of ... to (B) Independent of (C) Inversely proportional to (D) Proportional to the square o

Last Answer : (A) Proportional to

The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of the following resistance (s) is (are) controlling? (A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Description : The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of ... A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Last Answer : (B) Gas side

The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800

Description : The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800

Last Answer : (A) 500

The continuity equation (A) Is independent of the compressibility of the fluid (B) Is dependent upon the viscosity of the fluid (C) Represents the conservation of mass (D) None of these

Description : The continuity equation (A) Is independent of the compressibility of the fluid (B) Is dependent upon the viscosity of the fluid (C) Represents the conservation of mass (D) None of these

Last Answer : (C) Represents the conservation of mass

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

Which of the following is the most controlling factor for the rate of bubble detachment from the hot solid surface? (A) Liquid density (B) Liquid viscosity (C) Hot surface temperature (D) Interfacial tension

Description : Which of the following is the most controlling factor for the rate of bubble detachment from the hot solid surface? (A) Liquid density (B) Liquid viscosity (C) Hot surface temperature (D) Interfacial tension

Last Answer : (D) Interfacial tension

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Description : Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Last Answer : A) Pipe length

Fluid resistance to shear depends upon its (A) Rate of transfer of molecular momentum (B) Cohesion (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Fluid resistance to shear depends upon its (A) Rate of transfer of molecular momentum (B) Cohesion (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The rate of shear versus the shear stress curves are time dependent for __________ fluid. (A) Thixotropic (B) Rheopectic (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The rate of shear versus the shear stress curves are time dependent for __________ fluid. (A) Thixotropic (B) Rheopectic (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Description : A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Last Answer : (B) 0.025

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

The rate at which dissolution occurs is LEAST dependent upon which one of the following factors: w) temperature x) pressure y) solution concentration z) solute surface area

Description : The rate at which dissolution occurs is LEAST dependent upon which one of the following factors: w) temperature x) pressure y) solution concentration z) solute surface area

Last Answer : ANSWER: X -- PRESSURE

Crystal size in a continuous crystalliser depends upon the (A) Rate of heat transfer (B) Degree of turbulence (C) Degree of super-saturation (D) All (A), (B) and (C)

Description : Crystal size in a continuous crystalliser depends upon the (A) Rate of heat transfer (B) Degree of turbulence (C) Degree of super-saturation (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In an interphase heat transfer process, the equilibrium state corresponds to equality of temperature in the two phases, while the condition for equilibrium in an interphase mass transfer process is equality of (A) Concentrations (B) Chemical potentials (C) Activity co-efficients (D) Mass transfer co-efficients

Description : In an interphase heat transfer process, the equilibrium state corresponds to equality of temperature in the two phases, while the condition for equilibrium in an interphase mass transfer process is ... B) Chemical potentials (C) Activity co-efficients (D) Mass transfer co-efficients

Last Answer : (A) Concentrations

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Description : Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Last Answer : Option A

Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Description : Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Last Answer : (D) None of these

(4) Water drops in a dispersion medium of air Explanation: A colloid is a substance microscopically dispersed evenly throughout another substance. A colloidal system consists of two separate phases: a dispersed phase (or internal phase) and a continuous phase (or dispersion medium) in which the colloid is dispersed. A colloidal system may be solid, liquid, or gas. Cloud is a colloidal dispersion of Water drops in a dispersion medium of air.

Description : (4) Water drops in a dispersion medium of air Explanation: A colloid is a substance microscopically dispersed evenly throughout another substance. A colloidal system consists of two separate phases: a dispersed ... or gas. Cloud is a colloidal dispersion of Water drops in a dispersion medium of air.

Last Answer : Conduction band electrons have more mobility than holes because they – (1) are lighter (2) experience collision less frequently (3) have negative charge (4) need less energy to move them

(2) Fat is dispersed in water Explanation: A colloid is a substance microscopically dispersed evenly throughout another substance. A colloidal system consists of two separate phases: a dispersed phase (or internal phase) and a continuous phase (or dispersion medium) in which the colloid is dispersed. A colloidal system may be solid, liquid, or gas. Milk is an emulsified colloid of liquid butterfat globules dispersed within a water-based solution.

Description : (2) Fat is dispersed in water Explanation: A colloid is a substance microscopically dispersed evenly throughout another substance. A colloidal system consists of two separate phases: a dispersed ... Milk is an emulsified colloid of liquid butterfat globules dispersed within a water-based solution.

Last Answer : The presence of ozone in the stratosphere is responsible for – (1) increasing the average global temperature in recent years (2) higher rate of photosynthesis (3) checking the penetration of ultra-violet rays to the earth (4) supplying oxygen for people travelling in jets

(2) Fat is dispersed in water Explanation: A colloid is a substance microscopically dispersed evenly throughout another substance. A colloidal system consists of two separate phases: a dispersed phase (or internal phase) and a continuous phase (or dispersion medium) in which the colloid is dispersed. A colloidal system may be solid, liquid, or gas. Milk is an emulsified colloid of liquid butterfat globules dispersed within a water-based solution.

Description : (2) Fat is dispersed in water Explanation: A colloid is a substance microscopically dispersed evenly throughout another substance. A colloidal system consists of two separate phases: a dispersed ... Milk is an emulsified colloid of liquid butterfat globules dispersed within a water-based solution.

Last Answer : The presence of ozone in the stratosphere is responsible for – (1) increasing the average global temperature in recent years (2) higher rate of photosynthesis (3) checking the penetration of ultra-violet rays to the earth (4) supplying oxygen for people travelling in jets

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Description : Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Last Answer : (A) Keeping the heat transfer surface clean

Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Description : Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Last Answer : (A) Mass transfer co-efficient

Efficiency of a heat engine working on Carnot cycle between two temperature levels depends upon the (A) Two temperatures only (B) Pressure of working fluid (C) Mass of the working fluid (D) Mass and pressure both of the working fluid

Description : Efficiency of a heat engine working on Carnot cycle between two temperature levels depends upon the (A) Two temperatures only (B) Pressure of working fluid (C) Mass of the working fluid (D) Mass and pressure both of the working fluid

Last Answer : (A) Two temperatures only

The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Description : The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number

Last Answer : (D) Dependent on the Reynolds number

Which one of the following statement is correct? (A) Radiant energy expressed in Joules, is the energy associated with electromagnetic radiation (B) The rate of transfer of radiant energy is called flux and is expressed in watts (C) The radiant energy which falls upon a surface is termed as irradiance (D) All of these

Description : Which one of the following statement is correct? (A) Radiant energy expressed in Joules, is the energy associated with electromagnetic radiation (B) The rate of transfer of radiant energy is called flux ... ) The radiant energy which falls upon a surface is termed as irradiance (D) All of these

Last Answer : Answer: Option D

A patient with gross fecal contamination and peritonitis from a ruptured sigmoid diverticulum has his midline wound left open to heal by secondary intention. Which of the following statement(s) describes this healing process? a. Wounds healing in this fashion have an altered sequence of healing compared to a primarily closed wound b. A bed of granulation tissue forms over exposed subcutaneous tissue c. Epithelialization is enhanced in the face of bacterial colonization d. The ability of a wound to form granulation tissue is dependent on the blood supply of the tissue

Description : A patient with gross fecal contamination and peritonitis from a ruptured sigmoid diverticulum has his midline wound left open to heal by secondary intention. Which of the following statement(s) describes this ... of a wound to form granulation tissue is dependent on the blood supply of the tissue

Last Answer : Answer: b, d Open wounds, whether they be ulcers or open surgical incisions closing by secondary intention, heal with the same sequence of inflammation, matrix deposition, epithelialization ... via bacterial and phagocytic cell products such as proteases, collagenases, elastases, and other enzymes

Evaporation from water surfaces exposed to air is not dependent of the: w) velocity of the wind x) humidity y) temperature z) depth of the water

Description : Evaporation from water surfaces exposed to air is not dependent of the: w) velocity of the wind x) humidity y) temperature z) depth of the water 

Last Answer : ANSWER: Z -- DEPTH OF THE WATER 

Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Description : Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Fluid flow in a real packed bed can be approximated as __________ model. (A) Plug flow (B) Dispersion (C) Mixed flow (D) Tank in series

Description : Fluid flow in a real packed bed can be approximated as __________ model. (A) Plug flow (B) Dispersion (C) Mixed flow (D) Tank in series

Last Answer : (B) Dispersion

Fractional solvent extraction (A) Employs only one solvent (B) Employs two solvents (C) Results in low interfacial tension (D) None of these

Description : Fractional solvent extraction (A) Employs only one solvent (B) Employs two solvents (C) Results in low interfacial tension (D) None of these

Last Answer : (B) Employs two solvents

The amount of current flow required for the cathodic protection of a vessel is dependent upon the _________. A. amount of bare steel surface B. speed of the ship through the water C. temperature of the water D. all of the above

Description : The amount of current flow required for the cathodic protection of a vessel is dependent upon the _________. A. amount of bare steel surface B. speed of the ship through the water C. temperature of the water D. all of the above

Last Answer : Answer: D

Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Description : Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The internal energy of an incompressible fluid depends upon its (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The internal energy of an incompressible fluid depends upon its (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

The following are true about cerebrospinal fluid: a. it has a greater buffering capacity than plasma b. it has a similar chloride concentration to plasma c. it is a plasma ultrafiltrate d. the rate of formation is dependent on the intraventricular pressure over the normal pressure range

Description : The following are true about cerebrospinal fluid: a. it has a greater buffering capacity than plasma b. it has a similar chloride concentration to plasma c. it is a plasma ultrafiltrate d. the rate of formation is dependent on the intraventricular pressure over the normal pressure range

Last Answer : it is a plasma ultrafiltrate

Economy of a multiple effect evaporator depends upon the (A) Heat balance consideration (B) Rate of heat transfer (C) Both (A) and (B) (D) Neither (A) nor (B

Description : Economy of a multiple effect evaporator depends upon the (A) Heat balance consideration (B) Rate of heat transfer (C) Both (A) and (B) (D) Neither (A) nor (B

Last Answer : (A) Heat balance consideration

In most of the mechanically agitated liquid-liquid extractors, baffles or horizontal compartmental plates are provided, which helps in (A) Reducing the axial mixing (B) Increasing the rate of extraction (C) Maintaining the concentration difference between the two phases (D) All 'a', 'b' & 'c'

Description : In most of the mechanically agitated liquid-liquid extractors, baffles or horizontal compartmental plates are provided, which helps in (A) Reducing the axial mixing (B) Increasing the rate of extraction (C) Maintaining the concentration difference between the two phases (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Filtration rate does not depend upon the (A) Pressure drop & area of filtering surface (B) Resistance of the cake & the septum (C) Properties of the cake & the filtrate (D) None of these

Description : Filtration rate does not depend upon the (A) Pressure drop & area of filtering surface (B) Resistance of the cake & the septum (C) Properties of the cake & the filtrate (D) None of these

Last Answer : (D) None of these

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Description : Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Last Answer : C) Both 'a' & 'b'

A packed tower compared to a plate tower for a particular mass transfer operation (A) Incurs smaller pressure drop (B) Allows installation of cooling coils (C) Is less costly when built in large sizes/diameters (D) Is more suitable, if suspended solids are present in fluid stream

Description : A packed tower compared to a plate tower for a particular mass transfer operation (A) Incurs smaller pressure drop (B) Allows installation of cooling coils (C) Is less costly when built in large sizes/diameters (D) Is more suitable, if suspended solids are present in fluid stream

Last Answer : (A) Incurs smaller pressure drop

In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/s (B) μ , α and θ all have units of m2/s (C) α and θ have units of m2/s, while μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Description : In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/ ... μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Last Answer : Option C