In distillation column design, the McCabe-Thiele procedure is inadequate and a Ponchan-Savarit procedure is needed, when (A) Saturated feed is not used (B) An azeotrope forms (C) The latent heat of vaporisation of the more and less volatile components are greatly different (D) A total condenser is used

In distillation column design, the McCabe-Thiele procedure is
inadequate and a Ponchan-Savarit procedure is needed, when
(A) Saturated feed is not used
(B) An azeotrope forms
(C) The latent heat of vaporisation of the more and less volatile components
are greatly different
(D) A total condenser is used
by

1 Answer

Answer :

(D) A total condenser is used
by

Related questions

Which of the following assumes constant molal vaporisation and overflow?(A) McCabe-Thiele method (B) Ponchan-Savarit method (C) Enthalpy concentration method (D) Plate absorption column

Description : Which of the following assumes constant molal vaporisation and overflow? (A) McCabe-Thiele method (B) Ponchan-Savarit method (C) Enthalpy concentration method (D) Plate absorption column

Last Answer : (A) McCabe-Thiele method

Pick out the correct statement. (A) Ponchan-Savarit method is more accurate than McCabe-Thiele method to determine the number of theoretical stages required for the separation of non￾ideal binary system by distillation (B) A sharp decrease in pressure drop is an indication of flooding in a distillation coloumn (C) Solvent used in extractive distillation should be of high volatility (D) Flash distillation is suitable for separating components which have very close boiling temperature

Description : Pick out the correct statement. (A) Ponchan-Savarit method is more accurate than McCabe-Thiele method to determine the number of theoretical stages required for the separation of ... Flash distillation is suitable for separating components which have very close boiling temperature

Last Answer : (A) Ponchan-Savarit method is more accurate than McCabe-Thiele method to determine the number of theoretical stages required for the separation of non￾ideal binary system by distillation

Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of theoretical plate calculation for distillation column (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Description : Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of ... (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Last Answer : (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column

Design calculation for multiple component distillation is done by (A) Ponchon-Savarit method (B) McCabe-Thiele method (C) Enthalpy concentration method (D) Tray to tray calculations

Description : Design calculation for multiple component distillation is done by (A) Ponchon-Savarit method (B) McCabe-Thiele method (C) Enthalpy concentration method (D) Tray to tray calculations

Last Answer : (D) Tray to tray calculations

McCabe-Thiele method of binary distillation does not assume that the (A) Sensible heat changes are negligible compared with latent heat changes (B) Molar latent heats of all components are equal (C) Heat of mixing is negligible (D) None of these

Description : McCabe-Thiele method of binary distillation does not assume that the (A) Sensible heat changes are negligible compared with latent heat changes (B) Molar latent heats of all components are equal (C) Heat of mixing is negligible (D) None of these

Last Answer : (D) None of these

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Entrainer used in Azeotropic distillation should (A) Form a low boiling azeotrope with one of the constituents of the mixture (B) Form a new azeotrope of low relative volatility with one of the constituents of the mixture (C) Have high latent heat of vaporisation (D) Have high viscosity to provide high tray efficiency

Description : Entrainer used in Azeotropic distillation should (A) Form a low boiling azeotrope with one of the constituents of the mixture (B) Form a new azeotrope of low relative volatility with one of the ... (C) Have high latent heat of vaporisation (D) Have high viscosity to provide high tray efficiency

Last Answer : (A) Form a low boiling azeotrope with one of the constituents of the mixture

In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Description : In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Last Answer : (A) Total

McCabe-Thiele method (A) Uses molal units for material and energy balance (B) Uses weight fractions to express liquid and vapour composition (C) Can use any type of units (D) Is more accurate than Ponchon-Savarit method

Description : McCabe-Thiele method (A) Uses molal units for material and energy balance (B) Uses weight fractions to express liquid and vapour composition (C) Can use any type of units (D) Is more accurate than Ponchon-Savarit method

Last Answer : (A) Uses molal units for material and energy balance

Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio (above the minimum reflux ratio), the fixed cost of the distillation column first increases and then decreases (C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Description : Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio ( ... (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Last Answer : C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux

If f = moles of vapour present per mole of feed, then the slope of feed line is (McCabe-Thiele method) (A) (1 - f)/f (B) - (f - 1)/f (C) -1/f (D) -f/(1 - f)

Description : If f = moles of vapour present per mole of feed, then the slope of feed line is (McCabe-Thiele method) (A) (1 - f)/f (B) - (f - 1)/f (C) -1/f (D) -f/(1 - f)

Last Answer : (C) -1/f

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Solvent used in extractive distillation (A) Is of low volatility (B) Forms a low boiling azeotrope (C) Forms a high boiling azeotrope (D) Does not alter the relative volatility of the original components

Description : Solvent used in extractive distillation (A) Is of low volatility (B) Forms a low boiling azeotrope (C) Forms a high boiling azeotrope (D) Does not alter the relative volatility of the original components

Last Answer : (B) Forms a low boiling azeotrope

A distillation column with N plates is being operated under normal conditions. At some point of time, the operation is shifted to total reflux condition (i.e., no product and residue are being withdrawn and feed to the column is stopped). At the new steady state, (A) Composition of vapors and that of liquid do not vary throughout the column (B) Reboiler load and condenser load are minimum (C) The top and bottom compositions are unchanged with and without total reflux (D) The top and bottom compositions correspond to the maximum enrichment available

Description : A distillation column with N plates is being operated under normal conditions. At some point of time, the operation is shifted to total reflux condition (i.e., no product and residue are ... and without total reflux (D) The top and bottom compositions correspond to the maximum enrichment available

Last Answer : (D) The top and bottom compositions correspond to the maximum enrichment available

Heat sensitive materials with very high latent heat of vaporisation may be economically separated using (A) Liquid extraction (B) Distillation (C) Evaporation (D) Absorption

Description : Heat sensitive materials with very high latent heat of vaporisation may be economically separated using (A) Liquid extraction (B) Distillation (C) Evaporation (D) Absorption

Last Answer : (A) Liquid extraction

The solvent used in liquid extraction should not have high latent heat of vaporisation, because (A) The pressure drop and hence the pumping cost will be very high (B) It cannot be recovered by distillation (C) Its recovery cost by distillation may be prohibitively high (D) It will decompose while recovering by distillation

Description : The solvent used in liquid extraction should not have high latent heat of vaporisation, because (A) The pressure drop and hence the pumping cost will be very high (B) It cannot ... by distillation may be prohibitively high (D) It will decompose while recovering by distillation

Last Answer : (C) Its recovery cost by distillation may be prohibitively high

The McCabe ΔL law states that the (A) Molar heats of vaporisation of components are nearly equal (B) Linear crystal growth rate depends on the degree of super-saturation (C) Linear crystal growth rate does not depend on the crystal size (D) Linear crystal growth rate depends on the crystal size

Description : The McCabe ΔL law states that the (A) Molar heats of vaporisation of components are nearly equal (B) Linear crystal growth rate depends on the degree of super-saturation (C) Linear ... does not depend on the crystal size (D) Linear crystal growth rate depends on the crystal size

Last Answer : (C) Linear crystal growth rate does not depend on the crystal size

It is desired to concentrate a 20% salt solution (20 kg of salt in 100 kg of solution) to a 30% salt solution in an evaporator. Consider a feed of 300 kg/min at 30°C. The boiling point of the solution is 110°C, the latent heat of vaporisation is 2100 kJ/kg and the specific heat of the solution is 4 kJ/kg.K. The rate at which the heat has to be supplied in (kJ/min) to the evaporator is (A) 3.06 × 10 5 (B) 6.12 × 10 5 (C) 7.24 × 10 5 (D) 9.08 × 10

Description : It is desired to concentrate a 20% salt solution (20 kg of salt in 100 kg of solution) to a 30% salt solution in an evaporator. Consider a feed of 300 kg/min at 30°C. The boiling point of the solution is 110°C, the latent heat of ... 3.06 10 5 (B) 6.12 10 5 (C) 7.24 10 5 (D) 9.08 10

Last Answer : (A) 3.06 × 10

When the feed to a distillation column is a saturated liquid, slope of thefeed line is(A) Zero(B) Unity(C) Infinity(D) None of these

Description : When the feed to a distillation column is a saturated liquid, slope of thefeed line is (A) Zero (B) Unity (C) Infinity (D) None of these

Last Answer : (C) Infinity

In McCabe-Thiele method, at infinite reflux ratio (A) The overhead product is minimum (B) Both the operating lines coincide with diagonal (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In McCabe-Thiele method, at infinite reflux ratio (A) The overhead product is minimum (B) Both the operating lines coincide with diagonal (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (A) The overhead product is minimum

In McCabe-Thiele method, at infinite reflux ratio (A) Number of plates is maximum (B) Overhead product is maximum (C) Both the operating lines coincide with the diagram (D) None of these

Description : In McCabe-Thiele method, at infinite reflux ratio (A) Number of plates is maximum (B) Overhead product is maximum (C) Both the operating lines coincide with the diagram (D) None of these

Last Answer : (C) Both the operating lines coincide with the diagram

Flash distillation is suitable for the separation of components (A) Having very close boiling points (B) Which form maximum boiling azeotrope (C) Having very wide boiling points (D) Which form minimum boiling azeotrope

Description : Flash distillation is suitable for the separation of components (A) Having very close boiling points (B) Which form maximum boiling azeotrope (C) Having very wide boiling points (D) Which form minimum boiling azeotrope

Last Answer : (C) Having very wide boiling points

When the solvent dissolves very little of solute, then (A) Solvent of low latent heat of vaporisation should be used (B) Solvent of low freezing point should be used (C) Large quantity of solvent is required to extract the solute (D) Very small quantity of solvent is required

Description : When the solvent dissolves very little of solute, then (A) Solvent of low latent heat of vaporisation should be used (B) Solvent of low freezing point should be used (C) Large quantity of solvent is required to extract the solute (D) Very small quantity of solvent is required

Last Answer : (C) Large quantity of solvent is required to extract the solute

An equipment which converts the latent or sensible heat of one fluid into the latent heat of vaporisation of another, is called a (A) Boiler (B) Heat exchanger (C) Recuperator (D) Regenerato

Description : An equipment which converts the latent or sensible heat of one fluid into the latent heat of vaporisation of another, is called a (A) Boiler (B) Heat exchanger (C) Recuperator (D) Regenerato

Last Answer : (B) Heat exchanger

In a cooling tower, water becomes cool by (A) Loosing sensible heat (B) Heat transfer to surroundings (C) Vaporisation due to heat loss to air (D) Loosing latent heat

Description : In a cooling tower, water becomes cool by (A) Loosing sensible heat (B) Heat transfer to surroundings (C) Vaporisation due to heat loss to air (D) Loosing latent heat

Last Answer : (A) Loosing sensible heat

Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of vaporisation is constant (C) Volume in the liquid state is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Description : Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of ... is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

High __________ is an undesirable property for a good refrigerant. (A) Specific heat (B) Latent heat of vaporisation (C) Viscosity (D) Specific vapor volume

Description : High __________ is an undesirable property for a good refrigerant. (A) Specific heat (B) Latent heat of vaporisation (C) Viscosity (D) Specific vapor volume

Last Answer : (C) Viscosity

ick out the undesirable property for a good refrigerant. (A) High thermal conductivity (B) Low freezing point (C) Large latent heat of vaporisation (D) High viscosity

Description : ick out the undesirable property for a good refrigerant. (A) High thermal conductivity (B) Low freezing point (C) Large latent heat of vaporisation (D) High viscosity

Last Answer : (D) High viscosity

Gibbs free energy per mole for a pure substance is equal to the (A) Latent heat of vaporisation (B) Chemical potential (C) Molal boiling point (D) Heat capacity

Description : Gibbs free energy per mole for a pure substance is equal to the (A) Latent heat of vaporisation (B) Chemical potential (C) Molal boiling point (D) Heat capacity

Last Answer : (B) Chemical potential

The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2. (A) 273.15 (B) 225.65 (C) 100.03 (D) 373.15

Description : The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2. (A) 273.15 (B) 225.65 (C) 100.03 (D) 373.15

Last Answer : (B) 225.65

Minimum reflux ratio in a distillation column results in (A) Optimum number of trays (B) Minimum reboiler size (C) Maximum condenser size (D) Minimum number of trays

Description : Minimum reflux ratio in a distillation column results in (A) Optimum number of trays (B) Minimum reboiler size (C) Maximum condenser size (D) Minimum number of trays

Last Answer : (C) Maximum condenser size

Steam at 1000C causes more severe burns than water at 100° C because (1) steam has no specific heat capacity (2) steam has latent heat of vaporisation (3) water has no specific heat capacity (4) water has latent heat of fusion

Description : Steam at 1000C causes more severe burns than water at 100° C because (1) steam has no specific heat capacity (2) steam has latent heat of vaporisation (3) water has no specific heat capacity (4) water has latent heat of fusion

Last Answer :  steam has latent heat of vaporisation

Pick out the wrong statement. (A) With decrease in feed temperature, the number of plates required for binary distillation decreases for a given ‘L/V’ ratio (B) The extraction per unit of total height for a short packed column is more effective than for a tall column, in case of liquid-liquid extraction(C) Natural draft cooling towers are made of ferroconcrete and its cross￾section is wider at the bottom(D) Vander wall adsorption is also called chemisorption

Description : Pick out the wrong statement. (A) With decrease in feed temperature, the number of plates required for binary distillation decreases for a given L/V' ratio (B) The extraction per unit ... and its cross￾section is wider at the bottom (D) Vander wall adsorption is also called chemisorption

Last Answer : (D) Vander wall adsorption is also called chemisorption

Why high latent heat of vaporisation is desirable in a refrigerant ?

Description : Why high latent heat of vaporisation is desirable in a refrigerant ?

Last Answer : A high latent heat of vaporisation of refrigerant results in small amount of refrigerant and thus lesser circulation system of refrigerant for same tonnage.

. For the same feed, feed quality and separation (in a distillation column), with the increase of total pressure, the number of ideal plates will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient, can't be predicted

Description : . For the same feed, feed quality and separation (in a distillation column), with the increase of total pressure, the number of ideal plates will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient, can't be predicted

Last Answer : (A) Increase

Flash distillation is suitable for separating the constituents of a binary system, which (A) Form minimum boiling azeotrope (B) Have very wide boiling points (C) Have very close boiling points (D) Form constant boiling azeotrope

Description : Flash distillation is suitable for separating the constituents of a binary system, which (A) Form minimum boiling azeotrope (B) Have very wide boiling points (C) Have very close boiling points (D) Form constant boiling azeotrope

Last Answer : (B) Have very wide boiling points

For a binary mixture with low relative volatility, (A) Use steam distillation (B) Use molecular distillation (C) Use high pressure distillation (D) An azeotrope may be formed during distillation

Description : For a binary mixture with low relative volatility, (A) Use steam distillation (B) Use molecular distillation (C) Use high pressure distillation (D) An azeotrope may be formed during distillation

Last Answer : (D) An azeotrope may be formed during distillation

In distillation where q is defined as the moles of liquid flow in the stripping section per mole of feed introduced, for saturated liquid feed (A) q > 1 (B) q < 1 (C) q = 1 (D) q = 0

Description : In distillation where q is defined as the moles of liquid flow in the stripping section per mole of feed introduced, for saturated liquid feed (A) q > 1 (B) q < 1 (C) q = 1 (D) q = 0

Last Answer : (C) q = 1

In case of steam distillation, the steam leaving the liquid is not completely saturated with distillate vapour, because(A) Temperature is less(B) Total pressure is less(C) Mixing of steam with the material being vaporised is not so intimate asto result in equilibrium condition(D) Saturated steam is used for steam distillation

Description : In case of steam distillation, the steam leaving the liquid is not completely saturated with distillate vapour, because (A) Temperature is less (B) Total pressure is less (C) Mixing of steam ... not so intimate as to result in equilibrium condition (D) Saturated steam is used for steam distillation

Last Answer : (C) Mixing of steam with the material being vaporised is not so intimate as to result in equilibrium condition

Which of the following unit operations makes use of Thiele-Geddes equation? (A) Liquid-liquid extraction (B) Solid-liquid extraction (C) Multi-component absorption with chemical reaction (D) Multi-component distillation

Description : Which of the following unit operations makes use of Thiele-Geddes equation? (A) Liquid-liquid extraction (B) Solid-liquid extraction (C) Multi-component absorption with chemical reaction (D) Multi-component distillation

Last Answer : (D) Multi-component distillation

In distillation, overhead product contains (A) Only one component (B) Two components (C) Any number of components (D) Only saturated liquid

Description : In distillation, overhead product contains (A) Only one component (B) Two components (C) Any number of components (D) Only saturated liquid

Last Answer : (C) Any number of components

Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Description : Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Last Answer : ✓ The main sources of air leakage found in condenser are given below: 1) There is leakage of air from atmosphere at the joint of the parts which are internally under a pressure less ... hence evaporation enthalpy of steam increases therefore more amount of cooling water required in the condenser. 

Saturated steam at 1 atm is discharged from a turbine at 1200 kg/h. Superheated steam at 300 0C and 1 atm is needed as a feed to a heat exchanger. To produce it, the turbine discharge stream is mixed with superheated steam at 400 0C, 1 atm and specific volume of 3.11 m 3 /kg. Calculate the amount of superheated steam at 300 0C produced and the volumetric flow rate of the 400 0C steam.

Description : Saturated steam at 1 atm is discharged from a turbine at 1200 kg/h. Superheated steam at 300 0C  and 1 atm is needed as a feed to a heat exchanger. To produce it, the turbine discharge ... amount of superheated steam at 300 0C produced and the volumetric flow rate of the  400 0C steam.

Last Answer : Solution 1. Mass balance of water 1200 + m1 = m2 ………………………………………… (1) …………………….1 mark 2. Energy balance (1200 kg/h)(2676 kJ/kg) + m1(3278 kJ/kg)

Removal of __________ heat is involved in the condensation of a vapor under saturated conditions. (A) Super (B) Sensible (C) Latent (D) Both (B) & (C)

Description : Removal of __________ heat is involved in the condensation of a vapor under saturated conditions. (A) Super (B) Sensible (C) Latent (D) Both (B) & (C)

Last Answer : (B) Sensible

Total reflux in a distillation operation requires minimum (A) Reboiler load (B) Number of plates (C) Condenser load (D) All (A), (B) and (C)

Description : Total reflux in a distillation operation requires minimum (A) Reboiler load (B) Number of plates (C) Condenser load (D) All (A), (B) and (C)

Last Answer : (B) Number of plates

In a binary distillation column, if the feed contains 40 mole % vapour, the q line will have a slope of (A) 1.5 (B) -0.6 (C) -1.5 (D) 0.6

Description : In a binary distillation column, if the feed contains 40 mole % vapour, the q line will have a slope of (A) 1.5 (B) -0.6 (C) -1.5 (D) 0.6

Last Answer : (C) -1.5

The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Description : The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Last Answer : (A) Increase

Pick out the wrong statement. (A) Critical moisture content is not a property of the material itself (B) A sharp increase in pressure drop gives an indication of the flooding in a distillation column (C) Separation of components is not possible in liquid extraction, if selectivity is unity (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Description : Pick out the wrong statement. (A) Critical moisture content is not a property of the material itself (B) A sharp increase in pressure drop gives an indication of the flooding in a ... unity (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

Last Answer : (D) Dehydration of ethyl alcohol is most economically done by molecular distillation at very high vacuum

According to the Fenske equation, what will be the minimum number of plates required in a distillation column to separate an equimolar binary mixture of components A and B into an overhead fraction containing 99 mol% A and a bottom fraction containing 98 mol% B ? Assume that relative volatility (αAB = 2) does not change appreciably in the column. (A) 5 (B) 9 (C) 12 (D) 28

Description : According to the Fenske equation, what will be the minimum number of plates required in a distillation column to separate an equimolar binary mixture of components A and B into an overhead fraction containing 99 mol% A and a ... in the column. (A) 5 (B) 9 (C) 12 (D) 28

Last Answer : (C) 12