Description : Paper like thin plastic articles can be produced by (A) Blow moulding (B) Vacuum thermo forming (C) Injection moulding (D) None of these
Last Answer : (B) Vacuum thermo forming
Description : Plastic tubes & pipes are generally made by __________ moulding. (A) Injection (B) Transfer (C) Extrusion (D) Compression
Last Answer : (C) Extrusion
Description : A jet engine turbine blade is normally manufactured by (A) Forging (B) Shell moulding (C) Investment casting (D) Pressure die casting
Last Answer : (C) Investment casting
Description : __________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion
Last Answer : (C) Transfer
Description : __________ moulding process cannot be used for thermoplastic plastics. (A) Compression (B) Extrusion (C) Injection (D) None of these
Last Answer : (C) Injection
Description : Production of a hollow product by inflation of a tube or parison is called the __________ process. (A) Blow moulding (B) Calendaring (C) Extrusion (D) Injection
Last Answer : (A) Blow moulding
Description : The passage between the nozzle and the __________ is called 'sprue' in case of injection moulding. (A) Runner (B) Cylinder (C) Mold (D) None of these
Last Answer : (A) Runner
Description : Pick up the correct statement from the following: (A) The plastic bottles are made by the process of blowing (B) The application of thermo-setting resins on sheets of paper, is called laminating ... placing raw material in the desired moulds, is known as moulding process (D) All the above
Last Answer : Answer: Option D
Description : Uniform ramming of sand in green sand moulding process leads to (A) Reduced chance of gas porosity (B) Greater dimensional stability of the casting (C) Uniform flow of molten metal into the mould cavity (D) Less sand expansion type of casting defect
Last Answer : Option B
Description : Tyres are made by (A) Injection moulding (B) Extrusion (C) Rotational moulding (D) Compression moulding
Last Answer : (C) Rotational moulding
Description : Properties of moulding sand are
Last Answer : Properties of moulding sand are: i) Cohesiveness or (strength) of sand, ii) Permeability (Porosity) iii) Plasticity iv) Thermal Stability v) Refractoriness vi) Flow ability, vii) ... be reusable and should produce good casting surface. x) It should be bad conductor of heat.
Description : Explain any four properties of Moulding sand.
Last Answer : 1. Porosity: Molten metal always contain a certain amount of dissolved gases, which are evolved when the metal freezes the molten metal coming in contact with the moist sand , generates steam or ... to the casting. Refractoriness is measured by the sinter point of the sand rather than its melting
Description : Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand. (A) Parting (B) Synthetic (C) Loam (D) Dry
Last Answer : (A) Parting
Description : For removal of very small amounts of precipitate from large volume of water, the most suitable filter is the __________ filter. (A) Plate & frame (B) Shell & lea (C) Sand (D) Rotary vacuum
Last Answer : (C) Sand
Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B)
Description : Which one of the following is not a direct rapid tooling method? a.LOM Composite b.Direct AIM (ACES Injection Molding) c.Sand Molding d.Injection molding
Last Answer : d.Injection molding
Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators
Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators
Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film coefficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'
Last Answer : (D) All 'a', 'b' & 'c'
Description : Which of the following process is not formative process? a.Bending b.Plastic injection molding c.Selective Laser Sintering d.Forging
Last Answer : c.Selective Laser Sintering
Description : Where can I learn about plastic injection mold?
Last Answer : Plastic injection molding is a complex form of molding that uses plastic pellets and you heat them into a desired shape. Plastic injection molding can be very expensive when purchasing tools. ... more information on plastic injection molding go to http://www.engineersedge.com/injection_molding.htm.
Description : Pick out the true statement pertaining to water treatment. (A) Slow sand filters can remove colour completely (B) Activated carbon can be used for taste & odour control without subsequent filtration ... of water (D) Normally, the turbidity is removed by adding a coagulant prior to sedimentation
Last Answer : (D) Normally, the turbidity is removed by adding a coagulant prior to sedimentation
Description : A pug mill is used for (A) Softening brick earth (B) Moulding brick earth (C) Tempering brick earth (D) Providing brick earth
Last Answer : Answer: Option C
Description : The process of mixing clay, water and other ingredients to make brick is known as (A) Kneading (B) Moulding (C) Pugging (D) Drying
Last Answer : Answer: Option A
Description : Pug mill is used for (A) Preparation of clay (B) Moulding of clay (C) Drying of bricks (D) Burning of bricks
Description : Carbonisation of coal consists of A. drying and crushing the coal to a fine powder B. moulding the finely ground coal under pressure with or without a binding material C. heating the wood with a limited supply of air to temperature not less than 280°C D. none of the above
Last Answer : Answer: D
Description : A pug mill is used for a) Softening brick earth b) Moulding brick earth c) Tempering brick earth* d) Compacting brick earth
Last Answer : c) Tempering brick earth*
Description : What is moulding?
Last Answer : Moulding is the process of giving required shape & size to the plastic material (like concrete / clay) till it harden by external surface support.
Description : Which of the manufacturing processes is/are required to make a typical stainless steel spoon out of sheet metal? A. Casting B. Forming C. Brazing D. Blow moulding
Last Answer : Forming
Description : Which one of the following clays behaves like a dense sand? (A) Over-consolidated clay with a high over-consolidation ratio (B) Over-consolidated clay with a low over-consolidation ratio (C) Normally consolidated clay (D) Under-consolidated clay
Description : The proportions of lime and sand in the mortar normally used in brick construction are (A) 1 : 2 (B) 1 : 4 (C) 1 : 6 (D) 1 : 8
Description : Quantity of coke oven gas produced by high temperature carbonisation of one ton of dry coal may be around __________ Nm3 . (A) 30 (B) 300 (C) 3,000 (D) 30,000
Last Answer : (B) 300
Description : Reciprocating screens are normally inclined at an angle of 5° with the horizontal and employ gyratory motion at feed end & reciprocating motion at the discharge end. They are not suitable for the ... Dry chemicals (C) Heavy tonnages of rocks or gravel (D) Powdered food & granular materials
Last Answer : (C) Heavy tonnages of rocks or gravel
Description : Pick up the correct statement about silt soil from the following: (A) The silt soil has particle size from 0.02 mm to 0.06 mm (B) In organic fine grained silt soil possesses no ... The least plastic type normally consists of more or less equidimensional grains of quartz (D) All the above
Description : Pick out the wrong statement. (A) Percentage of ash in coke produced from medium coking coal is more than that in coal (B) The calorific value (kcal/Nm3 ) of coke oven gas reduces on ... plants in India at Talcher (Orissa) and Ramagundam (A.P) employ Kopper-Totzek process of coal gasification
Last Answer : (C) Ash is normally removed as 'fly-ash' in Kopper-Totzek process of coal gasification
Description : Pick out the correct statement. (A) Compression ratio of an Otto engine is comparatively higher than a diesel engine (B) Efficiency of an Otto engine is higher than that of a diesel ... Diesel engine normally operates at lower compression ratio than an Otto engine for an equal output of work
Last Answer : (B) Efficiency of an Otto engine is higher than that of a diesel engine for the same compression ratio
Description : The noble gases have low boiling points because: w) their ionization potentials are very low x) only weak Van der Waals forces hold the atoms together y) they are produced by the fractional distillation of liquid air z) they have eight electrons in the outer shell
Last Answer : ANSWER: X -- ONLY WEAK VAN DER WAALS FORCES HOLD THE ATOMS TOGETHER
Description : In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle
Last Answer : (A) Increases
Description : __________ heat exchanger is the most suitable, when the temperature of shell side fluid is much higher than that of tube side. (A) Single pass, fixed tube sheet (B) U-tube (C) Three pass, fixed tube sheet (D) None of these
Last Answer : (B) U-tube
Description : In a multipass shell and tube heat exchanger, tube side return pressure loss is equal to __________ the velocity head. (A) Twice (B) Four times (C) Square root of (D) Square of
Last Answer : (B) Four times
Description : The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4
Last Answer : (B) 4 0.8
Description : In a shell and tube heat exchanger, putting a longitudinal baffle across the shell, forces the shell side fluid to pass __________ through the heat exchanger. (A) Once (B) Twice (C) Thrice (D) Four times
Last Answer : (B) Twice
Description : If you like pretty gems that sparkle and shine, I invite you to dig in my virtual mine. My first is purple, fit for a king, My second is green where Dorothy did her thing. My third is red, July's ... gem, one letter in its turn, And you will find the stuff for which even the god's yearn. -Riddles
Last Answer : Ambrosia The gems are: Amethyst Emerald ( Emerald City in the Wizard of Oz ) Ruby Pearl Diamond Tiger's eye Cubic Zirconium (Fake diamond) Black Opal Taking the first letter of Amethyst, second of Emerald, etc.. gives Ambrosia - The food of the gods.
Description : How many square inches of dry sand make a pound?
Last Answer : Compacted?
Description : After digging Garlic, does it need to dry? Will it keep longer if buried in dry sand?
Last Answer : Garlic blubs need to dry like onions. they should dry outside in an airy protected spot for a few days until the leaves are dried up. Afterward, cut the leaves off, or braid them and hang them in a ... will last longer. As far as sand, I did hear of such a method, but not experienced with it.
Description : How much more does a wet cubic yard of sand weigh than dry cubic yard?
Last Answer : Exactly how much more it weighs will depend on how wet itis.
Description : The intensity of active earth pressure at a depth of 10 metres in dry cohesionless sand with an angle of internal friction of 30° and with a weight of 1.8 t/m3 , is (A) 4 t/m2 (B) 5 t/m2 (C) 6 t/m2 (D) 7 t/m2
Description : Pick up the correct statement from the following: (A) Bulking of sand is caused due to formation of a thin film of surface moisture (B) Fine sand bulks more than coarse sand (C) The volume of fully saturated sand, is equal to the volume of dry and loose sand (D) All the above
Description : Pick up the correct statement from the following: (A) Higher workability indicates unexpected increase in the moisture content (B) Higher workability indicates deficiency of sand (C) If the concrete mix is dry, the slump is zero (D) All the above
Description : Pick up the correct statement from the following: (A) The theory of formation of concrete is based on the phenomena of formation of voids (B) The bulking of sand is taken into account while ... sand and the sand completely flooded with water, have practically the same volume (D) All the above