Reciprocating screens are normally inclined at an angle of 5° with the horizontal and employ gyratory motion at feed end & reciprocating motion at the discharge end. They are not suitable for the screening of the (A) Light metal powder down upto 4 mesh size (B) Dry chemicals (C) Heavy tonnages of rocks or gravel (D) Powdered food & granular materials

Reciprocating screens are normally inclined at an angle of 5° with the
horizontal and employ gyratory motion at feed end & reciprocating motion
at the discharge end. They are not suitable for the screening of the
(A) Light metal powder down upto 4 mesh size
(B) Dry chemicals
(C) Heavy tonnages of rocks or gravel
(D) Powdered food & granular materials
by

1 Answer

Answer :

(C) Heavy tonnages of rocks or gravel
by

Related questions

Vibrating screens are used for handling large tonnages of materials. The vibrating motion is imparted to the screening surface by means of (A) Electromagnets (B) Cams or eccentric shafts (C) Unbalanced flywheels (D) Either (A), (B) or (C)

Description : Vibrating screens are used for handling large tonnages of materials. The vibrating motion is imparted to the screening surface by means of (A) Electromagnets (B) Cams or eccentric shafts (C) Unbalanced flywheels (D) Either (A), (B) or (C)

Last Answer : (D) Either (A), (B) or (C)

Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Description : Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Last Answer : (A) Have greater capacity per unit of discharge area

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

Pick out the wrong statement. (A) Nitrogen is normally supplied in fertiliser either in Ammoniacal or the nitrate form, from which the soil takes it up in the form of ammonium ions ornitrate ions and forms amino acids(B) Calcium present in the fertiliser helps in correcting the soil acidity(C) Particle size range of a good granular fertiliser is 10-15 mesh and itcontains less moisture as compared to finely divided powder form of fertiliser(D) Ammonium nitrate fertiliser is obtained as a by-product in an integratedsteel plant having by-product coke ovens

Description : Pick out the wrong statement. (A) Nitrogen is normally supplied in fertiliser either in Ammoniacal or the nitrate form, from which the soil takes it up in the form of ammonium ions ornitrate ... nitrate fertiliser is obtained as a by-product in an integrated steel plant having by-product coke ovens

Last Answer : (D) Ammonium nitrate fertiliser is obtained as a by-product in an integrated steel plant having by-product coke ovens

Tabling process used for separating two materials of different densities by passing the dilute pulp over a table/deck, which is inclined from the horizontal surface at an angle of about (A) 1 to 2° (B) 2 to 5° (C) 5 to 10° (D) 10 to 15°

Description : Tabling process used for separating two materials of different densities by passing the dilute pulp over a table/deck, which is inclined from the horizontal surface at an angle of about (A) 1 to 2° (B) 2 to 5° (C) 5 to 10° (D) 10 to 15°

Last Answer : (B) 2 to 5°

A retaining wall 6m high supports a backfill with a surcharge angle of 10°. The back of the wall is inclined to the vertical at a positive batter angle of 5°. If the angle of wall friction is 7°, then the resultant active earth pressure will act at a distance of 2 m above the base and inclined to the horizontal at an angle of (A) 7° (B) 10° (C) 12° (D) 17

Description : A retaining wall 6m high supports a backfill with a surcharge angle of 10°. The back of the wall is inclined to the vertical at a positive batter angle of 5°. If the angle of wall friction is 7°, then the resultant ... inclined to the horizontal at an angle of (A) 7° (B) 10° (C) 12° (D) 17

Last Answer : (C) 12°

As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Description : As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Last Answer : (B) 93 LS

Trommels employ __________ for screening of materials. (A) Fibrous cloth(B) Woven wire screen(C) Punched plate(D) None of these

Description : Trommels employ __________ for screening of materials. (A) Fibrous cloth (B) Woven wire screen (C) Punched plate (D) None of these

Last Answer : (C) Punched plate

The process of passing water through beds of granular materials, is called (A) Screening (B) Sedimentation (C) Filtration (D) None of these

Description : The process of passing water through beds of granular materials, is called  (A) Screening  (B) Sedimentation  (C) Filtration  (D) None of these 

Last Answer : (C) Filtration 

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure drop (C) Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Last Answer : (B) Cake resistance is independent of the pressure drop

The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Last Answer : (B) 2.5 times

Vibrating screens have capacity in the range of __________ tons/ft 2 .mm mesh size. (A) 0.2 to 0.8 (B) 5 to 25 (C) 50 to 100 (D) 100 to 250

Description : Vibrating screens have capacity in the range of __________ tons/ft 2 .mm mesh size. (A) 0.2 to 0.8 (B) 5 to 25 (C) 50 to 100 (D) 100 to 250

Last Answer : (A) 0.2 to 0.8

or Indian standard (IS) screens, the mesh number is equal to its aperture size expressed to the nearest deca-micron (0.01 mm). Aperture width of IS screen of mesh number 50 will be approximately __________ microns. (A) 5 (B) 50 (C) 500 (D) 5000

Description : or Indian standard (IS) screens, the mesh number is equal to its aperture size expressed to the nearest deca-micron (0.01 mm). Aperture width of IS screen of mesh number 50 will be approximately __________ microns. (A) 5 (B) 50 (C) 500 (D) 5000

Last Answer : (C) 500

Higher is the mesh number, smaller will be the aperture size of the screen. It means that the aperture size of a 200 mesh screen will be smaller than that of 20 mesh screen. This is valid for(A) British standard screens(B) German standard screens (DIN 1171) etc(C) American standard screens (ASTM and Tyler standard screens)(D) All (A), (B) and (C)

Description : Higher is the mesh number, smaller will be the aperture size of the screen. It means that the aperture size of a 200 mesh screen will be smaller than that of 20 mesh screen. This is valid for (A) British ... (C) American standard screens (ASTM and Tyler standard screens) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Bucket elevators are not suitable for the vertical lifting of __________ materials. (A) Fine (e.g. - 200 mesh size coal) (B) Sticky (e.g. clay paste) (C) Small lumpy (e.g. grains and sand) (D) Free flowing

Description : Bucket elevators are not suitable for the vertical lifting of __________ materials. (A) Fine (e.g. - 200 mesh size coal) (B) Sticky (e.g. clay paste) (C) Small lumpy (e.g. grains and sand) (D) Free flowing

Last Answer : (B) Sticky (e.g. clay paste

__________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Description : __________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Last Answer : (B) Belt

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

Hydrometer measures the specific gravity of liquids based on the principles of buoyancy. Pycnometer is used to measure the specific gravity of (A) Powder & granular solids (B) Liquids (C) Low melting point semi-solids (D) All 'a', 'b' & 'c

Description : Hydrometer measures the specific gravity of liquids based on the principles of buoyancy. Pycnometer is used to measure the specific gravity of (A) Powder & granular solids (B) Liquids (C) Low melting point semi-solids (D) All 'a', 'b' & 'c

Last Answer : (D) All 'a', 'b' & 'c

For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Description : For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Last Answer : (B) Volume swept by piston for one complete revolution and the pressure in the cylinder

Rotary dryers cannot handle __________ materials. (A) Free flowing (B) Dry (C) Sticky (D) Granular

Description : Rotary dryers cannot handle __________ materials. (A) Free flowing (B) Dry (C) Sticky (D) Granular

Last Answer : (C) Sticky

The angle which an inclined surface makes with the horizontal when a body placed on it is on the point moving down is known as a.Angle of friction b.Angle of limiting friction c.Angle of inclination d.Angle of repose e.None of the above

Description : The angle which an inclined surface makes with the horizontal when a body placed on it is on the point moving down is known as a.Angle of friction b.Angle of limiting friction c.Angle of inclination d.Angle of repose e.None of the above

Last Answer : d. Angle of repose

The angle which an inclined plane makes with the horizontal when a body placed on it is about to move down is known as angle of (A) Friction (B) Limiting friction (C) Repose (D) Kinematic friction

Description : The angle which an inclined plane makes with the horizontal when a body placed on it is about to move down is known as angle of (A) Friction (B) Limiting friction (C) Repose (D) Kinematic friction

Last Answer : (C) Repose

Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Description : Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Last Answer : (D) 200 mesh screen has 200 openings per linear cm

If you Normally have a heavy period now light pink discharge and spotting Pregnant?

Description : If you Normally have a heavy period now light pink discharge and spotting Pregnant?

Last Answer : Could be it's possible

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

80% less than 200 mesh size particles are called (A) Smoke (B) Powder (C) Grit (D) Aggregates

Description : 80% less than 200 mesh size particles are called (A) Smoke (B) Powder (C) Grit (D) Aggregates

Last Answer : (B) Powder

A double acting reciprocating pump compared to a single acting pump (of almost same size working under same pressure levels) would give almost double (A) Head (B) Discharge (C) Efficiency (D) None of these

Description : A double acting reciprocating pump compared to a single acting pump (of almost same size working under same pressure levels) would give almost double (A) Head (B) Discharge (C) Efficiency (D) None of these

Last Answer : (B) Discharge

Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Description : Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Last Answer : (B) 0.087 L.S

Pick out the correct statement. (A) The capacity and the effectiveness of a screen are the same (B) The capacity and the effectiveness of screen are opposing factors (C) The screening surface of a 'reel' (a revolving screen used in flour mills) is made of silk bolting cloth supported by wire mesh (D) Both (B) and (C)

Description : Pick out the correct statement. (A) The capacity and the effectiveness of a screen are the same (B) The capacity and the effectiveness of screen are opposing factors (C) The screening surface of a 'reel' (a ... flour mills) is made of silk bolting cloth supported by wire mesh (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing guide vane angle at inlet as 90o c) Providing runner vane angle at exit as 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Description : For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing ... 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Last Answer : d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to the shape of the particles, concrete aggregates are classified as rounded irregular, angular and flaky (C) According to the surface texture of the particles, the concrete aggregates are classified as glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Description : Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to ... glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above

Last Answer : Answer: Option D

Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Description : Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Work index is defined as the (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen (B) Energy needed to crush one tonne of feed to 200 microns (C) Energy (kWh/ton of feed) needed to crush small feed to such a size that 80% of the product passes a 200 mesh screen (D) Energy needed to crush one ton of feed to 100 microns

Description : Work index is defined as the (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen (B) Energy needed to crush ... of the product passes a 200 mesh screen (D) Energy needed to crush one ton of feed to 100 microns

Last Answer : (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen

Which form of e‐marketplace brings together buyers and sellers from multiple industries, often for MRO materials? a. horizontal b. Vertical c. Integrated d. Inclined

Description : Which form of e‐marketplace brings together buyers and sellers from multiple industries, often for MRO materials? a. horizontal b. Vertical c. Integrated d. Inclined

Last Answer : a. horizontal

What is a mixture of potassium nitrate powdered charcoal and sulphur called? (1) paint (2) aluminium (3) brass (4) gun powder

Description : What is a mixture of potassium nitrate powdered charcoal and sulphur called? (1) paint (2) aluminium (3) brass (4) gun powder

Last Answer : (4) gun powder Explanation: Gun powder is the mixture of potassium nitrate powdered charcoal and sulphur.

What is a mixture of potassium nitrate powdered charcoal and sulfur called? (1) paint (2) aluminum (3) brass (4) gun powder

Description : What is a mixture of potassium nitrate powdered charcoal and sulfur called? (1) paint (2) aluminum (3) brass (4) gun powder

Last Answer : (4) gun powder Explanation: Gun powder is the mixture of potassium nitrate powdered charcoal and sulfur.

What is a mixture of Potassium Nitrate Powdered Charcoal and Sulphur called? A. Paint B. Glass C. Gun Powder (Answer) D. Cement

Description : What is a mixture of Potassium Nitrate Powdered Charcoal and Sulphur called? A. Paint B. Glass C. Gun Powder (Answer) D. Cement

Last Answer : C. Gun Powder (Answer)

Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration permanently. 4. Have nearly uniform discharge. Which of these statements are corrects? (a) 1, 2 & 4 only (b) 1, 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Description : Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration ... 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Last Answer : (d) 1, 2, 3 & 4

The work done in sliding a block of weight of 50 kg up a plane inclined at an angle of 30? to the horizontal so that the block is lifted through 1 m ( a.More than 50 kgm b.50 kgm c.Less than 5 kgm d.15 kgm only e.None of the above

Description : The work done in sliding a block of weight of 50 kg up a plane inclined at an angle of 30? to the horizontal so that the block is lifted through 1 m ( a.More than 50 kgm b.50 kgm c.Less than 5 kgm d.15 kgm only e.None of the above

Last Answer : a. More than 50 kgm

The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Description : The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane

Last Answer : b. 30? with vertical

A body of weight W is resting at a plane inclined at 30? to the horizontal. It is attached to a string making an angle of 60? with horizontal. If the angle of friction be 30? the tension in the string would be a.Zero b.W c.W/2 d.2W e.None of the above

Description : A body of weight W is resting at a plane inclined at 30? to the horizontal. It is attached to a string making an angle of 60? with horizontal. If the angle of friction be 30? the tension in the string would be a.Zero b.W c.W/2 d.2W e.None of the above

Last Answer : c. W/2

A particle is projected with speed v at angle θ to the horizontal on an inclined surface making an angle Φ (Φ < θ) to the horizontal.

Description : A particle is projected with speed v at angle θ to the horizontal on an inclined surface making an angle Φ (Φ < θ) to the horizontal.

Last Answer : A particle is projected with speed v at angle θ to the horizontal on an inclined surface ... range of the projectile along the inclined surface.

A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of internal friction for the soil are respectively (A) 0.5 N/mm² and 30° (B) 0.05 N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Last Answer : Answer: Option B

A plane inclined at an angle to the horizontal at which the soil is expected to stay in the absence of any lateral support, is known as (A) Natural slope line (B) Repose line (C) The line (D) All the above

Description : A plane inclined at an angle to the horizontal at which the soil is expected to stay in the absence of any lateral support, is known as (A) Natural slope line (B) Repose line (C) The line (D) All the above

Last Answer : Answer: Option D

The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes (A) With the horizontal (B) With the vertical (C) With the perpendicular to the inclined plane of the soil (D) None of these

Description : The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes (A) With the horizontal (B) With the vertical (C) With the perpendicular to the inclined plane of the soil (D) None of these

Last Answer : Answer: Option A

An open vessel of water is accelerated up an inclined plane. The free water surface will (A) Be horizontal (B) Make an angle in direction of inclination of inclined plane (C) Make an angle in opposite direction to inclination of inclined plane (D) Any one of above is possible

Description : An open vessel of water is accelerated up an inclined plane. The free water surface will (A) Be horizontal (B) Make an angle in direction of inclination of inclined plane (C) Make an angle in opposite direction to inclination of inclined plane (D) Any one of above is possible

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) The minimum frequency of light for which no electrons are emitted, is called threshold frequency (B) Polarising angle of glass is 57.5° (C) At the polarising angle, the reflected and refracted rays are orthogonal (D) All the above

Description : Pick up the correct statement from the following: (A) The minimum frequency of light for which no electrons are emitted, is called threshold frequency (B) Polarising angle of glass is 57.5° (C) At the polarising angle, the reflected and refracted rays are orthogonal (D) All the above

Last Answer : Answer: Option D

Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Last Answer : (B) Gyratory crusher