Description : Production of a hollow product by inflation of a tube or parison is called the __________ process. (A) Blow moulding (B) Calendaring (C) Extrusion (D) Injection
Last Answer : (A) Blow moulding
Description : __________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion
Last Answer : (C) Transfer
Description : Plastic articles are normally produced by __________ moulding. (A) Green sand (B) Injection (C) Shell (D) Dry sand
Last Answer : (B) Injection
Description : Plastic tubes & pipes are generally made by __________ moulding. (A) Injection (B) Transfer (C) Extrusion (D) Compression
Last Answer : (C) Extrusion
Description : __________ moulding process cannot be used for thermoplastic plastics. (A) Compression (B) Extrusion (C) Injection (D) None of these
Last Answer : (C) Injection
Description : Paper like thin plastic articles can be produced by (A) Blow moulding (B) Vacuum thermo forming (C) Injection moulding (D) None of these
Last Answer : (B) Vacuum thermo forming
Description : Tyres are made by (A) Injection moulding (B) Extrusion (C) Rotational moulding (D) Compression moulding
Last Answer : (C) Rotational moulding
Description : Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2
Last Answer : c) 120-200 kg/cm2
Description : Hallow cone nozzle – liquid is fed into whirl chamber through entry or through a fixed spiral passage to give rotation motion. a. Axial b. Radial c. tangential. d. None of above
Last Answer : Ans- c. tangential.
Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B)
Description : Rapid low cost short life injection or blow mold tooling?
Last Answer : Could you be a little clearer on what you need? Are you making parts for the cabinets? How will they change? What size objects do you want to make with the injection molding equipment? I always seem to need clarification. :-(
Description : Where can I learn about plastic injection mold?
Last Answer : Plastic injection molding is a complex form of molding that uses plastic pellets and you heat them into a desired shape. Plastic injection molding can be very expensive when purchasing tools. ... more information on plastic injection molding go to http://www.engineersedge.com/injection_molding.htm.
Description : Tropical sprue?
Last Answer : DefinitionTropical sprue is a condition seen in residents of, or visitors to tropical areas. It impairs the absorption of nutrients from the intestines, causing malabsorption.See also: Celiac ... level (serum)Iron level (serum)Stool examination for bacteria and parasitesUpper endoscopyUpper GI s
Description : Celiac sprue is an example of which category of malabsorption? a) Mucosal disorders causing generalized malabsorption In addition to celiac sprue, regional enteritis and radiation ... malabsorption Postoperative gastric or intestinal resection can result in development of malabsorption syndromes.
Last Answer : a) Mucosal disorders causing generalized malabsorption In addition to celiac sprue, regional enteritis and radiation enteritis are examples of mucosal disorders.
Description : The contraction (Gaseous) porosity in inlays is related to:** A. Overheating of the alloy B. Molten gases C. Diameter of the sprue D. Overheating of investment
Last Answer : B. Molten gases
Description : Elaborate why the section of a sprue reduces downwards.
Last Answer : A sprue section reduces downwards to a smaller size at its bottom will create a choke which will help keep the sprue full of molten metal.
Description : In _____________ injection system only one pump is sufficient for multi-cylinder engine. a) air b) mechanical c) compression fuel d) common rail
Last Answer : Answer: d Explanation: None.
Description : With EFI of diesel engines a) sharp start and stop is not possible b) very high injection pressure can be obtained c) sudden cylinder cut-off is impossible d) diagnostic properties are poor
Last Answer : Answer: b Explanation: Generally, with EFI of diesel engines very high injection pressure can be obtained.
Description : Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold
Last Answer : ANSWER c. engine cylinder
Description : With diminishing cross-sectional area in case of subsonic flow in a converging nozzle, the (A) Velocity increases (B) Pressure decreases (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : The energy loss in flow through Venturimeter is less than that through flow nozzle, because in case of a flow nozzle, the (A) Length is shorter (B) Throat diameter is more (C) Sudden expansion of flow in the downstream occurs (D) Distance between the throat and the inlet is more
Last Answer : (C) Sudden expansion of flow in the downstream occurs
Description : In case of a pipe exit fitted with a nozzle, the (A) Conversion of kinetic head to pressure head is facilitated (B) Conversion of pressure head to kinetic head is facilitated (C) Power transmitted through the nozzle ... in the pipe is equal to one third of the total supply head (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C)
Description : In case of heat transfer by conduction in a hollow cylinder, __________ mean area is used to calculate the heat transfer rate. (A) Geometric (B) Arithmetic (C) Logarithmic (D) Either (A), (B) or (C)
Last Answer : (C) Logarithmic
Description : Bunsen burner is an example of a/an __________ burner. (A) Inside mixing/premix type (B) Outside mixing/diffusion flame/nozzle mix type (C) Rotary cup (D) Submerged combustion
Last Answer : (A) Inside mixing/premix type
Description : In a/an __________, the flow rate of fluids is obtained by measuring the difference between the impact and the static pressure. (A) Rotameter (B) Pitot tube (C) Venturimeter (D) Flow nozzle
Last Answer : (B) Pitot tube
Description : The effect of friction on the flow of steam through a nozzle is to decrease the __________ of steam. (A) Wetness (B) Mass flow rate (C) Both 'a' & 'b' (D) Neither 'a' nor 'b'
Last Answer : (C) Both 'a' & 'b'
Description : A jet engine turbine blade is normally manufactured by (A) Forging (B) Shell moulding (C) Investment casting (D) Pressure die casting
Last Answer : (C) Investment casting
Description : Uniform ramming of sand in green sand moulding process leads to (A) Reduced chance of gas porosity (B) Greater dimensional stability of the casting (C) Uniform flow of molten metal into the mould cavity (D) Less sand expansion type of casting defect
Last Answer : Option B
Description : Pick up the correct statement from the following: (A) The plastic bottles are made by the process of blowing (B) The application of thermo-setting resins on sheets of paper, is called laminating ... placing raw material in the desired moulds, is known as moulding process (D) All the above
Last Answer : Answer: Option D
Description : The power transmitted through the nozzle is maximum when the head lost due to friction in the pipe is __________ of the total supply head. (A) One-half (B) One-third (C) Two-third (D) None of these
Last Answer : Answer: Option B
Description : A pug mill is used for (A) Softening brick earth (B) Moulding brick earth (C) Tempering brick earth (D) Providing brick earth
Last Answer : Answer: Option C
Description : The process of mixing clay, water and other ingredients to make brick is known as (A) Kneading (B) Moulding (C) Pugging (D) Drying
Last Answer : Answer: Option A
Description : Pug mill is used for (A) Preparation of clay (B) Moulding of clay (C) Drying of bricks (D) Burning of bricks
Description : Carbonisation of coal consists of A. drying and crushing the coal to a fine powder B. moulding the finely ground coal under pressure with or without a binding material C. heating the wood with a limited supply of air to temperature not less than 280°C D. none of the above
Last Answer : Answer: D
Description : A pug mill is used for a) Softening brick earth b) Moulding brick earth c) Tempering brick earth* d) Compacting brick earth
Last Answer : c) Tempering brick earth*
Description : What is moulding?
Last Answer : Moulding is the process of giving required shape & size to the plastic material (like concrete / clay) till it harden by external surface support.
Description : Which of the manufacturing processes is/are required to make a typical stainless steel spoon out of sheet metal? A. Casting B. Forming C. Brazing D. Blow moulding
Last Answer : Forming
Description : Properties of moulding sand are
Last Answer : Properties of moulding sand are: i) Cohesiveness or (strength) of sand, ii) Permeability (Porosity) iii) Plasticity iv) Thermal Stability v) Refractoriness vi) Flow ability, vii) ... be reusable and should produce good casting surface. x) It should be bad conductor of heat.
Description : Explain any four properties of Moulding sand.
Last Answer : 1. Porosity: Molten metal always contain a certain amount of dissolved gases, which are evolved when the metal freezes the molten metal coming in contact with the moist sand , generates steam or ... to the casting. Refractoriness is measured by the sinter point of the sand rather than its melting
Description : In case of a couple where the male is having a very low sperm count, which technique will be suitable for fertilisation? (a) Gamete Intracytoplasmic Fallopian Transfer (b) Artificial Insemination (c) Intracytoplasmic sperm injection (d) Intrauterine transfer
Last Answer : (b) Artificial Insemination
Description : In case of a couple where the male is having a very low sperm count, which technique will be suitable for fertilisation ? (1) Gamete intracytoplasmic fallopian transfer (2) Artificial Insemination (3) Intracytoplasmic sperm injection (4) Intrauterine transfer
Last Answer : (2) Artificial Insemination
Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe
Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump
Description : The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these
Last Answer : (B) Have different diameters
Description : Which area is used in case of heat flow by conduction through a cylinder? (A) Logarithmic mean area (B) Arithmetic mean area (C) Geometric mean area (D) None of these
Last Answer : (A) Logarithmic mean area
Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)
Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder
Description : . It is possible to integrate an automatic flow controller to a (A) Flow nozzle (B) Venturimeter (C) Rotameter (D) None of these
Last Answer : (C) Rotameter
Description : The most suitable flow measuring device for the fluid flow measurement in a very large diameter pipeline is a (A) Weir (B) Pitot tube (C) Kennison nozzle (D) V-notch
Description : An ideal nozzle design aims at (A) Minimising wall friction (B) Suppressing boundary layer separation (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : Sele(A) The discharge through a Venturimeter depends upon Δp only and isindependent of orientation of the meterct the correct statement. (B) A Venturimeter with a given gage difference discharges at a ... a given pipe line, whether a Venturimeter or a nozzle with the same throat dia is used
Last Answer : (A) The discharge through a Venturimeter depends upon Δp only and isindependent of orientation of the meterct the correct statement
Description : Select the correct statement. (A) The discharge through a Venturimeter depends upon Δp only and isindependent of orientation of the meter (B) A Venturimeter with a given gage difference discharges at a ... a given pipe line, whether a Venturimeter or a nozzle with the same throat dia is used
Last Answer : (A) The discharge through a Venturimeter depends upon Δp only and isindependent of orientation of the meter