Density of low density polythene is about __________ gm/c.c. (A) 0.38 (B) 0.56 (C) 0.81 (D) 0.91

Density of low density polythene is about __________ gm/c.c.
(A) 0.38
(B) 0.56
(C) 0.81
(D) 0.91
by

1 Answer

Answer :

(D) 0.91
by

Related questions

Density of high density polythene is about __________ gm/c.c. (A) 1.18 (B) 1.05 (C) 0.95 (D) 0.99

Description : Density of high density polythene is about __________ gm/c.c. (A) 1.18 (B) 1.05 (C) 0.95 (D) 0.99

Last Answer : (C) 0.95

__________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Description : __________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Last Answer : (A) High density

Cellulose acetate has very high film permeability among all the polymers of the order of 5000 gm/100 m2 . Which of the following polymers has the maximum film elongation (of the order of 100%)? (A) Water impermeable cellophane(B) Polythene(C) Cellulose acetate(D) Teflon

Description : Cellulose acetate has very high film permeability among all the polymers of the order of 5000 gm/100 m2 . Which of the following polymers has the maximum film elongation (of the order of 100%)? (A) Water impermeable cellophane (B) Polythene (C) Cellulose acetate (D) Teflon

Last Answer : (B) Polythene

A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Last Answer : Answer: A

Find the pressure due to a column of mercury 74.0 cm high.  a. 91.80 x 10^3 N/m^2  b. 73.56 x 10^2 N/m^2  c. 9.86 x 10^4 N/m^2  d. 87.2 x 10^4 N/m^2

Description : Find the pressure due to a column of mercury 74.0 cm high.  a. 91.80 x 10^3 N/m^2  b. 73.56 x 10^2 N/m^2  c. 9.86 x 10^4 N/m^2  d. 87.2 x 10^4 N/m^2

Last Answer : 9.86 x 10^4 N/m^2

A sample of natural gas containing 80% methane (CH4 ) and rest nitrogen (N2 ) is burnt with 20% excess air. With 80% of the combustibles producing CO2 and the remainder going to CO, the Orsat analysis in volume percent is (A) CO2 : 6.26, CO : 1.56, O2 : 3.91, H2O :15.66, N2 : 72.60 (B) CO2 : 7.42, CO : 1.86, O2 : 4.64, N2 :86.02 (C) CO2 : 6.39, CO : 1.60, O2 : 3.99, H2O:25.96, N2 :72.06 (D) CO2 : 7.60, CO : 1.90, O2 : 4.75, N2 : 85.74

Description : A sample of natural gas containing 80% methane (CH4 ) and rest nitrogen (N2 ) is burnt with 20% excess air. With 80% of the combustibles producing CO2 and the remainder going to CO, the Orsat analysis in volume percent is (A) CO2 : 6 ... 96, N2 :72.06 (D) CO2 : 7.60, CO : 1.90, O2 : 4.75, N2 : 85.74

Last Answer : (B) CO2 : 7.42, CO : 1.86, O2 : 4.64, N2 :86.02

Catalyst used in the production of high density polythene by low pressure Ziegler process is(A) Aluminium triethyl activated with TiCl4(B) Platinum(C) Molybdenum(D) Nickel

Description : Catalyst used in the production of high density polythene by low pressure Ziegler process is (A) Aluminium triethyl activated with TiCl4 (B) Platinum (C) Molybdenum (D) Nickel

Last Answer : (A) Aluminium triethyl activated with TiCl4

Low density polythene as compared to high density polythene is (A) Harder (B) Tougher (C) Chemically inert (D) More flexible

Description : Low density polythene as compared to high density polythene is (A) Harder (B) Tougher (C) Chemically inert (D) More flexible

Last Answer : (D) More flexible

Addition polymerisation is not involved in the manufacture of (A) Low density polythene (B) Poly vinyl chloride (C) Polystyrene (D) Polyhexamethylene adipamide

Description : Addition polymerisation is not involved in the manufacture of (A) Low density polythene (B) Poly vinyl chloride (C) Polystyrene (D) Polyhexamethylene adipamide

Last Answer : (D) Polyhexamethylene adipamide

Zeigler process (A) Produces high density polythene(B) Uses no catalyst(C) Produces low density polythene(D) Employs very high pressure

Description : Zeigler process (A) Produces high density polythene (B) Uses no catalyst (C) Produces low density polythene (D) Employs very high pressure

Last Answer : (A) Produces high density polythene

Low pressure Zeigler process of polythene manufacture (A) Employs a pressure of 30 kgf/cm2 (B) Achieves an yield of 95-98% based on ethylene (C) Produces very low density polythene (D) Does not use any catalyst for polymerisation

Description : Low pressure Zeigler process of polythene manufacture (A) Employs a pressure of 30 kgf/cm2 (B) Achieves an yield of 95-98% based on ethylene (C) Produces very low density polythene (D) Does not use any catalyst for polymerisation

Last Answer : (B) Achieves an yield of 95-98% based on ethylene

Polythene (low or high density) containers are not corroded by (A) Sulphuric acid (10%) at room temperature (B) Nitric acid (95%) at room temperature (C) Sulphur trioxide at 60°C (D) Any of these

Description : Polythene (low or high density) containers are not corroded by (A) Sulphuric acid (10%) at room temperature (B) Nitric acid (95%) at room temperature (C) Sulphur trioxide at 60°C (D) Any of these

Last Answer : (A) Sulphuric acid (10%) at room temperature

Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205

Description : Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205

Last Answer : (B) 135

What is the greatest common factor of 49 81 and 91?

Description : What is the greatest common factor of 49 81 and 91?

Last Answer : The GCF is 1.

What is the greatest common factor of 49 81 and 91?

Description : What is the greatest common factor of 49 81 and 91?

Last Answer : The GCF is 1.

From a vessel containing 100 litres of ****,10 litres are drawn out and an equal amount of water is added. From the mixture,10 litres is again drawn out and same quantity of water is added. What is the final ratio of **** and water? a) 91 : 9 b) 81 : 19 c) 80 : 20 d) 90 : 10 e) None of these

Description : From a vessel containing 100 litres of wine,10 litres are drawn out and an equal amount of water is added. From the mixture,10 litres is again drawn out and same quantity of water is added. What is the final ratio of wine and water? a) 91 : 9 b) 81 : 19 c) 80 : 20 d) 90 : 10 e) None of these

Last Answer : Quantity of wine after two replacements = 100 l × (90/100)2 =81 l Required ratio = 81 : ( 100 – 81 )= 81 : 19 Answer: b)

Give one example of each for low density polythene and high density polthene.

Description : Give one example of each for low density polythene and high density polthene.

Last Answer : Ans: LDP. Squeze bottle and toys  HDP. Buckets, dustbin, bottles.

Liquefied Petroleum Gas (LPG) in domestic use cylinders is in the liquid form. The density of LPG in liquid form is about __________ of that of water (i.e. 1 gm/c.c). (A) One fourth (B) One third (C) Half (D) One eighth

Description : Liquefied Petroleum Gas (LPG) in domestic use cylinders is in the liquid form. The density of LPG in liquid form is about __________ of that of water (i.e. 1 gm/c.c). (A) One fourth (B) One third (C) Half (D) One eighth

Last Answer : (C) Half

Find the median of the data 35, 28, 49, 56, 79, 81, 73 and 80.

Description : Find the median of the data 35, 28, 49, 56, 79, 81, 73 and 80.

Last Answer : Find the median of the data 35, 28, 49, 56, 79, 81, 73 and 80. A. 64.5 B. 65 C. 65.5 D. 66

What is located in 56 n 38 e?

Description : What is located in 56 n 38 e?

Last Answer : Those coordinates would place you to the North East ofMoscow.

What is the nearest city of 56 degrees North and 38 degrees East?

Description : What is the nearest city of 56 degrees North and 38 degrees East?

Last Answer : 56 N 38 E is Shchyolkovsky District, Moscow Oblast, Russia.The nearest city is Russia's capital, Moscow.

What nearest city in 56 north and 38 east?

Description : What nearest city in 56 north and 38 east?

Last Answer : 56 N 38 E is the Shchyolkovsky District, Moscow Oblast, Russia.The nearest city is Moscow.

What is the location of 56 degrees N and 38 degrees E?

Description : What is the location of 56 degrees N and 38 degrees E?

Last Answer : 56 N 38 E is Shchyolkovsky District, Moscow Oblast, Russia. Itis 1 h 25 min (75.2 km) ftom Moscow.

What is the nearest city at 56 n 38 e?

Description : What is the nearest city at 56 n 38 e?

Last Answer : What is the answer ?

What city is located at 56 degrees N and 38 degrees E?

Description : What city is located at 56 degrees N and 38 degrees E?

Last Answer : Need answer

Male literacy rate in India according to 2001 census is - (1) 45.96 per cent (2) 56.38 per cent (3) 75.85 per cent (4) 64.13 per cent

Description : Male literacy rate in India according to 2001 census is - (1) 45.96 per cent (2) 56.38 per cent (3) 75.85 per cent (4) 64.13 per cent

Last Answer : (3) 75.85 per cent Explanation: As per the 2001 Census, the literacy rate of India increased from 18.33% in 1951 to 64.84% in 2001. The male literacy rate increased to 75.26%, which showed an ... at a much faster rate of 14.38%. According to 2011 census, male literacy rate in India is 80.9%.

The average age of K and L is 48 years. If M replaced K, the average age would be 40 and if M replaced L, the average would be 44. What are the ages of K,L,M repectively? A) 58, 46, 22 B) 32, 44, 36 C) 52,44,36 D) 56, 22,38

Description :  The average age of K and L is 48 years. If M replaced K, the average age would be 40 and if M replaced L, the average would be 44. What are the ages of K,L,M repectively? A) 58, 46, 22 B) 32, 44, 36 C) 52,44,36 D) 56, 22,38

Last Answer : Answer: C)  Total age of K& L = 48*2 = 96 yrs----->1 Total age of L& M = 40*2 = 80yrs----->2 Total age of K& M = 44*2 = 88 yrs----->3 from 1, 2, 3 K+L+M =132---->4 from 1 & 4, M= 36 from 2 & 4, K=52 from 3 & 4, L=44 Hence the required answer is 52,44,36 

There are three different categories of jobs A, B and C. The average salary of the students who got the job of A and B categories is Rs.32 lakh per annum. The average salary of the student who got the job of B and C category is 54 lakh per annum. And the average salary of those students who got the job of A and C is Rs.44 lakh per annum. The most appropriate (or closet) range of average salary of all the three categories (if it is known that each student gets only one category for jobs i.e, A, B and C): A) lies between 30 & 44 B) lies between 48 & 56 C) lies between 38 & 45 D) lies between 49 & 50

Description : There are three different categories of jobs A, B and C. The average salary of the students who got the job of A and B categories is Rs.32 lakh per annum. The average salary of the student who got the job of B ... 30 & 44 B) lies between 48 & 56 C) lies between 38 & 45 D) lies between 49 & 50

Last Answer : Answer: C) Let the number of students who got the jobs of A, B and C categories is a, b and c respectively, ∴Total salary of Aand B = 32 (a +b) ∴Total salary of B and C = 54 (b+ ... the minimum salary must be Rs.38 lakh and the maximum salary cannot exceed 45, which is the highest of the three..

Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Description : Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Last Answer : (A) 7 kgf/cm2 and 70 °C

Automobile steering wheels are normally made of (A) Cellulose acetate(B) Cellulose nitrate(C) PVC(D) High density polythene

Description : Automobile steering wheels are normally made of (A) Cellulose acetate (B) Cellulose nitrate (C) PVC (D) High density polythene

Last Answer : (A) Cellulose acetate

Transistor parts and refrigerator components are normally made of (A) Polystyrene (B) Polyester (C) High density polythene (D) Polyurethane

Description : Transistor parts and refrigerator components are normally made of (A) Polystyrene (B) Polyester (C) High density polythene (D) Polyurethane

Last Answer : (A) Polystyrene

Hydrated density of HD lipoproteins is (A) 0.94 gm/ml (B) 0.94–1.006 gm/ml (C) 1.006–1.063 gm/ml (D) 1.063–1.21 gm/ml

Description : Hydrated density of HD lipoproteins is (A) 0.94 gm/ml (B) 0.94–1.006 gm/ml (C) 1.006–1.063 gm/ml (D) 1.063–1.21 gm/ml

Last Answer : Answer : D

Hydrated density of (HD) lipoproteins is (A) 0.94 gm/ml (B) 0.94-1.006 gm/ml (C) 1.006-1.063 gm/ml (D) 1.063-1.21 gm/l

Description : Hydrated density of (HD) lipoproteins is (A) 0.94 gm/ml (B) 0.94-1.006 gm/ml (C) 1.006-1.063 gm/ml (D) 1.063-1.21 gm/l

Last Answer : Answer : B

Poise is converted into stoke by (A) Multiplying with density (gm/c.c) (B) Dividing by density (gm/c.c) (C) Multiplying with specific gravity (D) Dividing by specific gravity

Description : Poise is converted into stoke by (A) Multiplying with density (gm/c.c) (B) Dividing by density (gm/c.c) (C) Multiplying with specific gravity (D) Dividing by specific gravity

Last Answer : (B) Dividing by density (gm/c.c)

Low pressure Zeigler process for the manufacture of polythene uses a catalyst which is (A) Ni (B) V2O5 (C) Fe (D) Aluminium triethyl combined with titanium tetrachloride

Description : Low pressure Zeigler process for the manufacture of polythene uses a catalyst which is (A) Ni (B) V2O5 (C) Fe (D) Aluminium triethyl combined with titanium tetrachloride

Last Answer : (D) Aluminium triethyl combined with titanium tetrachloride

__________ is a thermosetting plastic. (A) PVC (B) Polythene (C) Bakelite (D) Polystyrene

Description : __________ is a thermosetting plastic. (A) PVC (B) Polythene (C) Bakelite (D) Polystyrene

Last Answer : (C) Bakelite

__________ tubes are good substitute for human blood vessels on heart by-pass operation. (A) PVC (B) Polythene (C) Teflon/Dacron (D) Polystyrene

Description : __________ tubes are good substitute for human blood vessels on heart by-pass operation. (A) PVC (B) Polythene (C) Teflon/Dacron (D) Polystyrene

Last Answer : (C) Teflon/Dacron

Vinyl flooring is done using __________ sheets. (A) Polypropylene (B) PVC (C) Polythene (D) Polyvinyl acetate

Description : Vinyl flooring is done using __________ sheets. (A) Polypropylene (B) PVC (C) Polythene (D) Polyvinyl acetate

Last Answer : (B) PVC

__________ scrap can be recycled & reutilised. (A) Bakelite (B) Epoxy resin (C) Polythene (D) None of these

Description : __________ scrap can be recycled & reutilised. (A) Bakelite (B) Epoxy resin (C) Polythene (D) None of these

Last Answer : (C) Polythene

__________ is an addition polymer (A) Nylon (B) Bakelite (C) Polythene (D) None of these

Description : __________ is an addition polymer (A) Nylon (B) Bakelite (C) Polythene (D) None of these

Last Answer : (C) Polythene

In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament form. Dry spinning is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Description : In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament ... is used for __________ fibres. (A) Polythene (B) PVC (C) Rayon (D) Polyvinyl acetate

Last Answer : (B) PVC

Polythene is a/an __________ polymerisation product. (A) Addition (B) Condensation (C) Thermosetting (D) None of these

Description : Polythene is a/an __________ polymerisation product. (A) Addition (B) Condensation (C) Thermosetting (D) None of these

Last Answer : (A) Addition

__________ is a thermosetting plastic. (A) Polyvinyl chloride (B) Polythene (C) Bakelite (D) Teflon

Description : __________ is a thermosetting plastic. (A) Polyvinyl chloride (B) Polythene (C) Bakelite (D) Teflon

Last Answer : (C) Bakelite

__________ is a thermosetting plastic. (A) Polythene (B) Epoxy polymer (C) P.V.C. (D) Polystyrene

Description : __________ is a thermosetting plastic. (A) Polythene (B) Epoxy polymer (C) P.V.C. (D) Polystyrene

Last Answer : (B) Epoxy polymer

__________ is produced using Polycondensation reaction. (A) Polythene (B) Phenol formaldehyde (C) Poly vinyl chloride (D) None of these

Description : __________ is produced using Polycondensation reaction. (A) Polythene (B) Phenol formaldehyde (C) Poly vinyl chloride (D) None of these

Last Answer : (B) Phenol formaldehyde

A sample of saturated soil has 30% water content and the specific gravity of soil grains is 2.6. The dry density of the soil mass in g/cm3 , is (A) 1.47 (B) 1.82 (C) 1.91 (D) None of these

Description : A sample of saturated soil has 30% water content and the specific gravity of soil grains is 2.6. The dry density of the soil mass in g/cm3 , is (A) 1.47 (B) 1.82 (C) 1.91 (D) None of these

Last Answer : (D) None of these

The range of electromagnetic spectrum important in heat transfer by radiation is __________ microns. (A) 0.38-0.78 (B) 0.5-50 (C) 100-1000 (D) 5-50

Description : The range of electromagnetic spectrum important in heat transfer by radiation is __________ microns. (A) 0.38-0.78 (B) 0.5-50 (C) 100-1000 (D) 5-50

Last Answer : (B) 0.5-50

If dry density, water density and specific gravity of solids of a given soil sample are 1.6 g/cc, 1.84 g/cc and 2.56 respectively, the porosity of the soil sample, is (A) 0.375 (B) 0.370 (C) 0.380 (D) 0.390

Description : If dry density, water density and specific gravity of solids of a given soil sample are 1.6 g/cc, 1.84 g/cc and 2.56 respectively, the porosity of the soil sample, is (A) 0.375 (B) 0.370 (C) 0.380 (D) 0.390

Last Answer : (A) 0.375

In a 100 quadrat study of 1 sqm each Cyperus rotundus was found in 80 quadrats with overall of 5640 individuals. The frequency (%), abun dance and density (m2) would be a). 70.5, 80.0 and 56.4 b). 56.4, 70.5 and 80.0 c). 80.0, 70.5 and 56.4 d). 80.0, 56.4 and 70.5

Description : In a 100 quadrat study of 1 sqm each Cyperus rotundus was found in 80 quadrats with overall of 5640 individuals. The frequency (%), abun dance and density (m2) would be a). 70.5, 80.0 and 56.4 b). 56.4, 70.5 and 80.0 c). 80.0, 70.5 and 56.4 d). 80.0, 56.4 and 70.5

Last Answer : c). 80.0, 70.5 and 56.4

The density of water at 4°C is  a. 1 gm/cm³  b. 2 gm/cm³  c. 3 gm/cm³  d. 4 gm/cm³

Description : The density of water at 4°C is  a. 1 gm/cm³  b. 2 gm/cm³  c. 3 gm/cm³  d. 4 gm/cm³

Last Answer : 1 gm/cm³