Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205

Softening point of high density polythene is about __________ °C.
(A) 85
(B) 135
(C) 165
(D) 205
by

1 Answer

Answer :

(B) 135
by

Related questions

Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Description : Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Last Answer : (A) 7 kgf/cm2 and 70 °C

What is the GCF of 225 135 and 165?

Description : What is the GCF of 225 135 and 165?

Last Answer : The GCF is 15.

The ratio between two number is 3:4 ,if each number be increased by 9, the ratio becomes 18:23 find the sum of the number a) 135 b) 105 c) 155 d) 165 e) None of these

Description : The ratio between two number is 3:4 ,if each number be increased by 9, the ratio becomes 18:23 find the sum of the number a) 135 b) 105 c) 155 d) 165 e) None of these

Last Answer : Let the two numbers be 3x and 4x. When they are increased by 9 they become 3x + 9 and 4x + 9. It is given that the ratio is 18:23 Thus, 3x + 9/4x + 9 = 18:23 23(3x + 9) = 18(4x + 9) 69x + 207 = 72x ... = -45 X = 15 Thus two numbers are 3x15 = 45 and 4 x 15 = 60 And the sum is 60+45 = 105 Answer: b)

Find out the wrong number in the sequence: 125, 127, 130, 135, 142, 153, 165 (A) 130 (B) 142 (C) 153 (D) 165

Description : Find out the wrong number in the sequence: 125, 127, 130, 135, 142, 153, 165 (A) 130 (B) 142 (C) 153 (D) 165

Last Answer : Answer: C Difference 125 and 127 is 2, then 3, 5, 7, 11, and 12. Except 12 all are prime numbers so 165 is wrong in series.

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

__________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Description : __________ polythene is most prone to stress-cracking (A) High density (B) Low density (C) Cross-linked (D) Linear low density

Last Answer : (A) High density

Density of high density polythene is about __________ gm/c.c. (A) 1.18 (B) 1.05 (C) 0.95 (D) 0.99

Description : Density of high density polythene is about __________ gm/c.c. (A) 1.18 (B) 1.05 (C) 0.95 (D) 0.99

Last Answer : (C) 0.95

Is blood pressure 135 over 85 normal for a 62 year old male?

Description : Is blood pressure 135 over 85 normal for a 62 year old male?

Last Answer : No - but its common. 135/85 is above "normal" - ideal is 120/80or (slightly) lower.

The tyrosine residues per molecule of thyroglobulin is (A) 85 (B) 95 (C) 115 (D) 135

Description : The tyrosine residues per molecule of thyroglobulin is (A) 85 (B) 95 (C) 115 (D) 135

Last Answer : Answer : C

As per IS : 1172-1963, water required per head per day for average domestic purposes, is (A) 50 litres (B) 65 litres (C) 85 litres (D) 135 litres

Description : As per IS : 1172-1963, water required per head per day for average domestic purposes, is  (A) 50 litres  (B) 65 litres  (C) 85 litres  (D) 135 litres

Last Answer : (D) 135 litres

Density of low density polythene is about __________ gm/c.c. (A) 0.38 (B) 0.56 (C) 0.81 (D) 0.91

Description : Density of low density polythene is about __________ gm/c.c. (A) 0.38 (B) 0.56 (C) 0.81 (D) 0.91

Last Answer : (D) 0.91

__________ test is done to find out the softening point of bitumen. (A) Impact (B) Ball and ring (C) Flame (D) Viscosity

Description : __________ test is done to find out the softening point of bitumen. (A) Impact (B) Ball and ring (C) Flame (D) Viscosity

Last Answer : (B) Ball and ring

Heavy water has maximum density at __________ °C. (A) 4 (B) 11.6 (C) 0 (D) 18.6

Description : Heavy water has maximum density at __________ °C. (A) 4 (B) 11.6 (C) 0 (D) 18.6

Last Answer : (B) 11.6

If the pressure on 100 c.c. of air is halved, then its volume (at the same temperature) would be __________ c.c. (A) 100 (B) 50 (C) 205 (D) 200

Description : If the pressure on 100 c.c. of air is halved, then its volume (at the same temperature) would be __________ c.c. (A) 100 (B) 50 (C) 205 (D) 200

Last Answer : (D) 200

Catalyst used in the production of high density polythene by low pressure Ziegler process is(A) Aluminium triethyl activated with TiCl4(B) Platinum(C) Molybdenum(D) Nickel

Description : Catalyst used in the production of high density polythene by low pressure Ziegler process is (A) Aluminium triethyl activated with TiCl4 (B) Platinum (C) Molybdenum (D) Nickel

Last Answer : (A) Aluminium triethyl activated with TiCl4

Low density polythene as compared to high density polythene is (A) Harder (B) Tougher (C) Chemically inert (D) More flexible

Description : Low density polythene as compared to high density polythene is (A) Harder (B) Tougher (C) Chemically inert (D) More flexible

Last Answer : (D) More flexible

Zeigler process (A) Produces high density polythene(B) Uses no catalyst(C) Produces low density polythene(D) Employs very high pressure

Description : Zeigler process (A) Produces high density polythene (B) Uses no catalyst (C) Produces low density polythene (D) Employs very high pressure

Last Answer : (A) Produces high density polythene

Automobile steering wheels are normally made of (A) Cellulose acetate(B) Cellulose nitrate(C) PVC(D) High density polythene

Description : Automobile steering wheels are normally made of (A) Cellulose acetate (B) Cellulose nitrate (C) PVC (D) High density polythene

Last Answer : (A) Cellulose acetate

Transistor parts and refrigerator components are normally made of (A) Polystyrene (B) Polyester (C) High density polythene (D) Polyurethane

Description : Transistor parts and refrigerator components are normally made of (A) Polystyrene (B) Polyester (C) High density polythene (D) Polyurethane

Last Answer : (A) Polystyrene

Polythene (low or high density) containers are not corroded by (A) Sulphuric acid (10%) at room temperature (B) Nitric acid (95%) at room temperature (C) Sulphur trioxide at 60°C (D) Any of these

Description : Polythene (low or high density) containers are not corroded by (A) Sulphuric acid (10%) at room temperature (B) Nitric acid (95%) at room temperature (C) Sulphur trioxide at 60°C (D) Any of these

Last Answer : (A) Sulphuric acid (10%) at room temperature

For heavier fuels the cooling system of an internal combustion engine, the temperature is maintained at a) 78 to 80°C b) 80 to 84 °C c) 85 to 88°C d) 88 to 90°C

Description : For heavier fuels the cooling system of an internal combustion engine, the temperature is maintained at a) 78 to 80°C b) 80 to 84 °C c) 85 to 88°C d) 88 to 90°C

Last Answer : d) 88 to 90°C

The ability of tool steel to resist softening at high temperatures is termed as __________ hardness. (A) Red (B) Extended (C) Super (D) Extreme

Description : The ability of tool steel to resist softening at high temperatures is termed as __________ hardness. (A) Red (B) Extended (C) Super (D) Extreme

Last Answer : (C) Super

Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150

Description : Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150

Last Answer : (B) 70

Find the electric field when the velocity of the field is 12m/s and the flux density is 8.75 units. a) 510 b) 105 c) 150 d) 165

Description : Find the electric field when the velocity of the field is 12m/s and the flux density is 8.75 units. a) 510 b) 105 c) 150 d) 165

Last Answer : b) 105

Give one example of each for low density polythene and high density polthene.

Description : Give one example of each for low density polythene and high density polthene.

Last Answer : Ans: LDP. Squeze bottle and toys  HDP. Buckets, dustbin, bottles.

Addition polymerisation is not involved in the manufacture of (A) Low density polythene (B) Poly vinyl chloride (C) Polystyrene (D) Polyhexamethylene adipamide

Description : Addition polymerisation is not involved in the manufacture of (A) Low density polythene (B) Poly vinyl chloride (C) Polystyrene (D) Polyhexamethylene adipamide

Last Answer : (D) Polyhexamethylene adipamide

Low pressure Zeigler process of polythene manufacture (A) Employs a pressure of 30 kgf/cm2 (B) Achieves an yield of 95-98% based on ethylene (C) Produces very low density polythene (D) Does not use any catalyst for polymerisation

Description : Low pressure Zeigler process of polythene manufacture (A) Employs a pressure of 30 kgf/cm2 (B) Achieves an yield of 95-98% based on ethylene (C) Produces very low density polythene (D) Does not use any catalyst for polymerisation

Last Answer : (B) Achieves an yield of 95-98% based on ethylene

Softening temperature of coal ash is a measure of the __________ of coal. (A) Caking tendency (B) Coking tendency (C) Clinkering tendency (D) Size stability

Description : Softening temperature of coal ash is a measure of the __________ of coal. (A) Caking tendency (B) Coking tendency (C) Clinkering tendency (D) Size stability

Last Answer : (C) Clinkering tendency

Flash point of motor gasoline may be around __________ °C. (A) 10 (B) 45 (C) 100 (D) 150

Description : Flash point of motor gasoline may be around __________ °C. (A) 10 (B) 45 (C) 100 (D) 150

Last Answer : (B) 45

A mixture of 10% C6H6 vapour in air at 25°C and 750 mm Hg has a dew point of 20°C. Its dew point at 30°C and 700 mm Hg will be around __________ °C. (A) 21.7 (B) 20 (C) 27.3 (D) 18.7

Description : A mixture of 10% C6H6 vapour in air at 25°C and 750 mm Hg has a dew point of 20°C. Its dew point at 30°C and 700 mm Hg will be around __________ °C. (A) 21.7 (B) 20 (C) 27.3 (D) 18.7

Last Answer : (D) 18.7

Nitrobenzene (boiling point = 210.6°C) is steam distilled at 1 atm pressure. Nitrobenzene will distil off __________ °C. (A) At < 100 (B) At > 210.6 (C) Between 100 and 210 (D) None of these

Description : Nitrobenzene (boiling point = 210.6°C) is steam distilled at 1 atm pressure. Nitrobenzene will distil off __________ °C. (A) At < 100 (B) At > 210.6 (C) Between 100 and 210 (D) None of these

Last Answer : (A) At < 100

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Fusion point of coal ash generally varies from 1000 to 1700° C. Ash having fusion point less than __________ °C is liable to form clinker. (A) 1100 (B) 1250 (C) 1350 (D) 1400

Description : Fusion point of coal ash generally varies from 1000 to 1700° C. Ash having fusion point less than __________ °C is liable to form clinker. (A) 1100 (B) 1250 (C) 1350 (D) 1400

Last Answer : (A) 1100

Flash point of most vegetable oils is about __________ °C. (A) 50 (B) 100 (C) 200 (D) 300

Description : Flash point of most vegetable oils is about __________ °C. (A) 50 (B) 100 (C) 200 (D) 300

Last Answer : (C) 200

Purity of oxygen used for blowing in steel making L.D. converter is 99.5%. The boiling point of oxygen is about __________ °C. (A) -53 (B) -103 (C) -183 (D) -196

Description : Purity of oxygen used for blowing in steel making L.D. converter is 99.5%. The boiling point of oxygen is about __________ °C. (A) -53 (B) -103 (C) -183 (D) -196

Last Answer : (C) -183

Oxygen is separated by distillation from air after its liquefaction. The boiling point of oxygen is about __________ °C. (A) -83 (B) -183 (C) -196 (D) -218

Description : Oxygen is separated by distillation from air after its liquefaction. The boiling point of oxygen is about __________ °C. (A) -83 (B) -183 (C) -196 (D) -218

Last Answer : (B) -183

The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C. (A) 768 (B) 908 (C) 1400 (D) 1539

Description : The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C. (A) 768 (B) 908 (C) 1400 (D) 1539

Last Answer : Option A

Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or thermosetting (C) Branching in case of cross-linked polymers caused by small amount of impurities in bifunctional monomer formulation reduces its solubility and increases the softening point (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Description : Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or ... (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Last Answer : D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Mastication of rubber means (A) Its softening (B) A treatment to retard its deterioration due to oxidation (C) Improving its curing rate (D) Depression of its freezing point

Description : Mastication of rubber means (A) Its softening (B) A treatment to retard its deterioration due to oxidation (C) Improving its curing rate (D) Depression of its freezing point

Last Answer : (A) Its softening

Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of 2 kJ/kg.K enters at 20°C. The log mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50

Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50

Last Answer : (A) 32

Noise level audible to audience sitting in the 5th row from the stage during a large orchestra show corresponds to about __________ decibels. (A) 105 (B) 135 (C) 160 (D) 185

Description : Noise level audible to audience sitting in the 5th row from the stage during a large orchestra show corresponds to about __________ decibels. (A) 105 (B) 135 (C) 160 (D) 185

Last Answer : (B) 135

High speed steel tools retain their hardness upto a temperature of __________ °C.(A) 500 (B) 750 (C) 900 (D) 1100

Description : High speed steel tools retain their hardness upto a temperature of __________ °C. (A) 500 (B) 750 (C) 900 (D) 1100

Last Answer : (C) 900

High temperature carbonisation of coal takes place at __________ °C. (A) 2000 (B) 600 (C) 1100 (D) 1600

Description : High temperature carbonisation of coal takes place at __________ °C. (A) 2000 (B) 600 (C) 1100 (D) 1600

Last Answer : (C) 1100

Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are normally carried out at about __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Description : Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are ... __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Last Answer : (B) 900-1000

High temperature carbonisation of coal takes place at __________ °C. (A) 2000 (B) 700 (C) 1100 (D) < 500

Description : High temperature carbonisation of coal takes place at __________ °C. (A) 2000 (B) 700 (C) 1100 (D) < 500

Last Answer : (C) 1100

High speed steel tools retain their hardness upto a temperature of __________ °C. (A) 500 (B) 750 (C) 900 (D) 1100

Description : High speed steel tools retain their hardness upto a temperature of __________ °C. (A) 500 (B) 750 (C) 900 (D) 1100

Last Answer : Option C

Linear polymers are normally (A) Thermosetting (B) Thermoplastic (C) Elastometric (D) Having extremely high softening poin

Description : Linear polymers are normally (A) Thermosetting (B) Thermoplastic (C) Elastometric (D) Having extremely high softening poin

Last Answer : (B) Thermoplastic

A material is capable of resisting softening at high temperature, because of its property termed as (A) Hot temper (B) Hot hardness (C) Fatigue (D) Creep

Description : A material is capable of resisting softening at high temperature, because of its property termed as (A) Hot temper (B) Hot hardness (C) Fatigue (D) Creep

Last Answer : (B) Hot hardness

__________ is a thermosetting plastic. (A) PVC (B) Polythene (C) Bakelite (D) Polystyrene

Description : __________ is a thermosetting plastic. (A) PVC (B) Polythene (C) Bakelite (D) Polystyrene

Last Answer : (C) Bakelite

__________ tubes are good substitute for human blood vessels on heart by-pass operation. (A) PVC (B) Polythene (C) Teflon/Dacron (D) Polystyrene

Description : __________ tubes are good substitute for human blood vessels on heart by-pass operation. (A) PVC (B) Polythene (C) Teflon/Dacron (D) Polystyrene

Last Answer : (C) Teflon/Dacron