Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000
Last Answer : C. 125,000
Description : The minimum frame size required for a CSMA/CD based computer network running at 1 Gbps on a 200m cable with a link speed of 2 × 108m/s is a. 125 bytes b. 250 bytes c. 500 bytes d. None of these
Last Answer : b. 250 bytes
Description : A woman’s neglected hangnail has developed into a mild staphylococcal cellulites. Which of the following regimens would be appropriate oral therapy? (a) Dicloxacillin 125 mg q6h (b) Vancomycin 250 mg q6h (c) Methicillin 500 mg q6h (d) Cefazolin 1 g q8h (e) Penicillin V 500 mg q6h
Last Answer : Ans: A
Description : What is the recommended minimum range of illumination required by BS EN 970 for inspection of a welded surface? a) 90 to 125 lux b) 150 to 250 lux c) 350 to 500 lux d) 35 to 50 lux
Last Answer : c) 350 to 500 lux
Description : What is he required surface finish for raised or flat faced gasket surfaces? a) 63 µ in. b) 125 µ in-250 µ in. c) 250 µ in-400 µ in. d) 400-500 µ in.
Last Answer : b) 125 µ in-250 µ in.
Description : The CPU of a system having 1 MIPS execution rate needs 4 machine cycles on an average for executing an instruction. The fifty percent of the cycles use memory bus. A memory read/write employs one machine cycle. For ... (A) 500 Kbytes/sec (B) 2.2 Mbytes/sec (C) 125 Kbytes/sec (D) 250 Kbytes/sec
Last Answer : (D) 250 Kbytes/sec
Description : The length of a Marconi antenna to operate with 985 kHz is ______. A. 200 ft B. 500 ft C. 250 ft D. 999 ft
Last Answer : C. 250 ft
Description : What is the bandwidth available in the commercial C-band? A. 1000 MHz B. 36 MHz C. 250 MHz D. 500 MHz
Last Answer : D. 500 MHz
Description : In the North American TDM system, what is the transmission rate in Mbps of T3 carrier system? A. 44.736 B. 6.312 C. 3.152 D. 274.176
Last Answer : A. 44.736
Description : Which of the following is oldest multiplexing scheme? A. Frequency Division Multiplexing (FDM) B. Time Division Multiplexing (TDM) C. Code Division Multiplexing (CDM) D. Space Division Multiplexing (SDM)
Last Answer : D. Space Division Multiplexing (SDM)
Description : Multiplexing scheme use by baseband transmission. A. FDM B. Space multiplexing C. TDM D. Statistical multiplexing
Last Answer : C. TDM
Description : How would one squeeze more channels of communication into TDM frames of standard length? A. Shorten the time delay for each channel B. Raise the amplitude C. Add modulators D. Remove the synchronizing pulses
Last Answer : A. Shorten the time delay for each channel
Description : One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used
Last Answer : A. noise is amplified with voice when an FDM system is used
Description : The time it takes to transmit one TDM frame is called ______
Last Answer : Frame time
Description : What is the electrical wavelength of a 500 MHz signal? A. 60 centimeters B. 6 meters C. 0.06 meter D. 60 meters
Last Answer : A. 60 centimeters
Description : What is the wavelength of a signal at 500 MHz? A. 0.062 cm B. 6 meters C. 60 cm D. 60 meters
Last Answer : C. 60 cm
Description : If the purchases made during the year were Rs. 60,000, the balance of stock in trade at the beginning and at the end of the year were Rs. 12,000 and Rs. 9,000 respectively and the gross profit on sales was 1/5th, when which ... year ? (A) Rs. 15,750 (B) Rs. 14,000 (C) Rs. 12,500 (D) Rs. 17,250
Last Answer : Answer: Rs. 12,500
Description : On a test consisting of 500 questions, Dhivya answered 80% of the first 250 questions correctly. What percent of the other 250 questions does she need to answer correctly for her grade on the entire exam to be 60% ? a) 20 b) 60 c) 45 d) 80 e) 40
Last Answer : Answer: E 60% of 500 = 300 80% of 250 = 200 No. of correct answers in remaining 250 questions = 300 – 200 = 100 Percentage = 100 x 100/ 250 = 40%
Description : What is the lifetime of ILDs? a. 50,000 hours b. 75,000 hours c. 100,000 hours d. 125,000 hours
Last Answer : a. 50,000 hours
Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303
Last Answer : A. 30.3
Description : What volume of the chamber is required to measure absorption coefficient at 100 Hz? A. 125 m3 B. 50 m3 C. 150 m3 D. 352 m3
Last Answer : D. 352 m3
Description : A bus bar is 3 inches wide and 0.375 inches thick. What size of round conductor (in circular mils) is necessary to carry the same current as the bus bar? A. 1,125,000 circular mils B. 1,250,000 circular mils C. 1,432,000 circular mils D. 1,547,000 circular mils
Last Answer : Answer: C
Description : A cantilever shaft has a diameter of 6 cm and the length is 40cm, it has a disc of mass 125 kg at its free end. The Young’s modulus for the shaft material is 250 GN/m2. Calculate the static deflection in nm. a) 0.001 b) 0.083c) 1.022 d) 0.065
Last Answer : a) 0.001
Description : Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400
Last Answer : Large - L 300*250*200 Above 2.5 to 5 400
Description : Consider a link with packet loss probability of 0.2. What is the expected number of transmissions it would take to transfer 200 packets given that the stop and wait protocol is used? a. 125 b. 250 c. 225
Last Answer : b. 250
Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm
Last Answer : (C) 3.125 cm
Description : A sewer is laid from a manhole to a manhole , 250 m away along a gradient of 1 in 125. If the reduced level of the invert at is 205.75 m and the height of the boning rod is 3 m, the reduced level of the sight rail at , is (A) 208.75 m (B) 202.75 m (C) 206.75 m (D) 211.75 m
Last Answer : (C) 206.75 m
Description : Width of the shoulders of carriage way is generally kept (A) 100 cm (B) 125 cm (C) 150 cm (D) 250 cm
Last Answer : Answer: Option D
Description : The LCM of two numbers is 45 times their HCF. If one of the numbers is 125 and the sum of HCF and LCM is 1150, then the other number is? a) 100 b) 125 c) 250 d) 225 e) 180
Last Answer : LCM = 45× HCF LCM + HCF = 46× HCF = 1150 HCF = 25, LCM =1125. product of 2 numbers = LCM×HCF required number = (25× 1125) / 125 = 225. Answer: d)
Description : On an IQ test consisting of 250 questions, Jasvinder answered 40% of the first 125 questions correctly. What per cent of the other 125 questions does he need to answer correctly for his grade on the entire exam to be 60%? (a) 75% (b) 80% (c) 60% (d) Cannot be determined (e) None of these
Last Answer : (b) 80%
Description : What is the maximum surface roughness permitted by ASME B31.1 for the sidewall of ring grooves? a) 63 µ in b) 125 µ in. c) 250 µ in. d) 400 µ in
Last Answer : a) 63 µ in
Description : What is the maximum surface roughness for tongue and groove and small male and female gasket surfaces? a) 63 µ in b) 125 µ in c) 250 µ in d) 400 µ in
Last Answer : b) 125 µ in
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A
Last Answer : D. 2.0 A
Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 300 kph B. 100 kph C. 200 kph D. 250 kph
Last Answer : C. 200 kph
Description : The maximum propagation delay of a geostationary satellite is A. 278 ms B. 239 ms C. 300 ms D. 250 ms
Last Answer : A. 278 ms
Description : Reference temperature use in noise analysis A. 75 K B. 250 K C. 290 K D. 300 K
Last Answer : C. 290 K
Description : What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω
Last Answer : D. 2500 Ω
Description : During the night when the F2 layer combines with F1 layer it falls to what approximate height? A. 250 km B. 350 km C. 300 km D. 400 km
Last Answer : C. 300 km
Description : What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi
Last Answer : B.25mi
Description : What is the estimated medium wind loading in the Philippines for antenna tower design? A. 200 kph B. 250 kph C. 300 kph D. 100 kph
Last Answer : A. 200 kph
Description : If Ns=250, determine the earth radius k-factor. A. 1.98 B. 1.23 C. 1.33 D. 1.29
Last Answer : B. 1.23
Description : A loudspeaker cabinet has an internal volume of 5,184 in3 (84,950 cm3 ). It has a port area on the baffle of 50 in2 (322.58cm2 ) and a thickness of 0.70 in (18 mm). What is the Helmholtz resonance, in hertz, of this loudspeaker enclosure? A. 250 Hz B. 245 Hz C. 240 Hz D. 255 Hz
Last Answer : C. 240 Hz
Description : A speaker cabinet has an internal volume 84,950 cm3 . It has a port area on the baffle of 3,230 cm2 and baffle thickness of 19 mm. What is the Helmholtz resonance hertz of this speaker enclosure? A. 260 Hz B. 245 Hz C. 265 Hz D. 250 Hz
Last Answer : B. 245 Hz
Description : Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode
Last Answer : D. Packet mode
Description : Multiplexing in a time division multiplexer occurs based upon A. the position of a frame within the group of frames B. the positioning of data within a frame C. the priority assigned to a connected device D. the activity of a connected device
Last Answer : B. the positioning of data within a frame
Description : Convert each of the following fraction into a percentage: (i) 47 100 (ii) 9 20 (iii) 3 8 (iv) 8 125 (v) 19 500 (vi) 4 15 (vii) 2 3 (viii) 1 3 5 -Maths
Last Answer : We have the following: (i) 47100=47100×100% = 47% (ii) 920=920×100% =9×5%= 45% (iii) 38=38×100% =3×252%=752%=3712% (iv) 8125=8125×100%=8×45%=325%=6.4% (v) ... ;203%=803%=2623% (vii) 23=23×100%=2003%=6623% (viii) 135=85=85×100%=(8×20)%=160%
Description : Sundry Debtors – Rs.15,000 Bills Receivable (B/R) – Rs.12,500 Cash at Bank – Rs.17,500 Stock – Rs.15,000 Profit – Rs.20,000 Creditors – Rs.25,000 Bills Payable (B/P) – Rs.15,000 Sales – Rs.1,00,000 What is the Acid Test Ratio ? (A) 1•5 : 1 (B) 1•125 : 1 (C) 16 2/3% (D) 50%
Last Answer : Answer: 1•125 : 1
Description : For determine the specific gravity of soil solids, using a pycnometer of 500 cc., the following data is available : Weight of dry empty pycnometer = 125 g Weight of dried soil and pycnometer = 500 g Weight of dried soil and distilled ... of soil solids, is (A) 2.0 (B) 2.25 (C) 2.50 (D) 2.75
Last Answer : (C) 2.50
Description : Industrial steam generators operate at a steam capacity of? (rra) 1300 kg/s (rrb) 1000 kg/s (rrc) 500 kg/s ( d) 125 kg/s
Last Answer : ( d) 125 kg/s