Write the IF value of (i) FM ratio recevier. (ii) MW band AM.

Write the IF value of (i) FM ratio recevier. (ii) MW band AM.
by

1 Answer

Answer :

(i) 10.7 Mhz (ii) 455 Khz
by

Related questions

Compare narrow band FM with wide-band FM w.r.t. following points. (i) Modulation index (ii) Maximum deviation (iii)Range of modulating frequency (iv)Application

Description : Compare narrow band FM with wide-band FM w.r.t. following points. (i) Modulation index (ii) Maximum deviation (iii)Range of modulating frequency (iv)Application

Last Answer : Sr. No Parameters Narrow band FM Wide band FM 1 Modulation index Less than or slightly greater than 1 Greater than 1  2 Maximum deviation ... like police wireless, ambulance etc. Entertainment broadcasting can be used for high quality music transmission 

Draw and label PLL based FM detector.

Description : Draw and label PLL based FM detector.

Last Answer : Draw and label PLL based FM detector.

Define modulation index of FM.

Description : Define modulation index of FM.

Last Answer : Modulation index of FM is defined as the ratio of the frequency deviation to the modulating frequency.

Explain why reception for high frequency band is better during night time.

Description : Explain why reception for high frequency band is better during night time.

Last Answer : In sky wave propagation, the transmitted signal travels into the upper atmosphere where it is bent or reflected back to earth. This bending or reflection of signal takes place due to the presence ... reflected signal and hence the reception for high frequency band is better during night time.

Draw the block diagram of AM. Super heterodyne ratio receiver and state the function of each block

Description : Draw the block diagram of AM. Super heterodyne ratio receiver and state the function of each block

Last Answer : AM super heterodyne receiver works on the principle of super heterodyning. In the super heterodyne receiver, the incoming signal voltage is combined with a Signal generated in the receiver. The ... constant output level at the speaker even though the signal strength at the antenna varies.

A 400 W carrier is amplitude modulated to a depth of 75%.Calculate the total power in AM wave. (i) Explain the types of noise in a communication system. (ii) Compare simplex and duplex mode of communication.

Description : A 400 W carrier is amplitude modulated to a depth of 75%.Calculate the total power in AM wave. (i) Explain the types of noise in a communication system. (ii) Compare simplex and duplex mode of communication.

Last Answer : (i) Noise: Noise is any spurious or undesired disturbances that mask the received signal in a communication system. a) Atmospheric Noise: Atmospheric Noise is also known as static noise which is the ... remote control ExamplesWalkytalky,telephone,mobile,Radar, FAX,Pager 4

Define the term signal to noise ratio.

Description : Define the term signal to noise ratio. 

Last Answer : Signal to Noise ratio: The ratio of the strength of an electrical or other signal carrying information to that of unwanted interference is called as signal to noise ratio. OR Signal to Noise Ratio is defined as ... the same point. S/N=Ps/Pn where,Ps=Signal Power Pn=Noise Power at the same point

Compare sky wave and space wave propagation w.r.t. following points. (i) Frequency range (ii) Effect of fading (iii)Polarization (iv)Application

Description : Compare sky wave and space wave propagation w.r.t. following points. (i) Frequency range (ii) Effect of fading (iii)Polarization (iv)Application

Last Answer : Sr. No  Parameters Sky Wave Propagation Space Wave Propagation 1 Frequency range 3 MHz to 30 MHz  Above 30 MHz 2 Effect of fading Problem of fading is ... horizontally Polarized 4 Application RadioBroadcasting (SW Range) Used for TV and FM broadcasting

Write any one application of the following range. 1. Radio frequency 2. IR frequency 3. Medium frequency

Description : Write any one application of the following range. 1. Radio frequency 2. IR frequency 3. Medium frequency 

Last Answer : Application of 1. Radio Frequency- Radar signals and communication 2. IR Frequency- LED, Laser, TV remote, Used for directed links e.g. to connect different buildings via laser links. 3. Medium Frequency- AM broadcasting.

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

Derive a mathematical expression for AM wave.

Description : Derive a mathematical expression for AM wave.

Last Answer : Derive a mathematical expression for AM wave.

Sketch AM signal in (1)Time domain (2)Frequency domain.

Description : Sketch AM signal in (1)Time domain (2)Frequency domain.

Last Answer : AM in Time domain AM in frequency domain

Explain Tropospheric scatter propagation with sketch.

Description : Explain Tropospheric scatter propagation with sketch.

Last Answer : As the name implies, troposcatter uses the troposphere as the region that affects the radio signals being transmitted, returning them to Earth so that they can be received by the ... of "blurring" the overall received signal and this makes high speed data transmissions difficult.

Explain the working of half dipole antenna with its radiation pattern.

Description : Explain the working of half dipole antenna with its radiation pattern. 

Last Answer : Half wave dipole antenna diagram Explanation: 1. It is a resonant antenna 2. It is exact half wavelength (λ /2) long & open circuited at one end. 3. The dipole ... waves exist. Hence radiation pattern is bidirectional. The radiation pattern of half wave dipole antenna is -

Explain Electromagnetic spectrum.

Description : Explain Electromagnetic spectrum. 

Last Answer : The information signal should be first converted into an electromagnetic signal before transmission because the wireless transmission takes place using electromagnetic waves. The electromagnetic waves are oscillations which ... This entire range of frequency of EM waves is called EM spectrum.

Explain structure of rectangular microstrip patch antenna with its radiation pattern.

Description : Explain structure of rectangular microstrip patch antenna with its radiation pattern. 

Last Answer : In telecommunication, a microstrip antenna (also known as a printed antenna) usually means an antenna fabricated using microstrip techniques on a printed circuit board (PCB).It is a kind of ... microstrip transmission line with equivalent loads on either end to represent the radiation loss.

Explain the concept of De-emphasis with neat diagram.

Description : Explain the concept of De-emphasis with neat diagram. 

Last Answer : In the De-emphasis circuit, by reducing the amplitude level of the received high frequency signal by the same amount as the increase in pre-emphasis is termed as De-emphasis. The pre- ... de-emphasis circuit is a low pass filter or integrator which allows only low frequencies to pass. 

Draw the basic block diagram of Electronic communication system. State the function of transmitter.

Description : Draw the basic block diagram of Electronic communication system. State the function of transmitter.

Last Answer : Block diagram: Transmitter The function of the transmitter is to process the electrical signal from different aspects. For example in radio broadcasting the electrical signal obtained from sound ... the message signal are done just to ease the transmission of the signal through the channel.

Sketch the radiation pattern of Yagi-Uda antenna.

Description : Sketch the radiation pattern of Yagi-Uda antenna.

Last Answer : Sketch the radiation pattern of Yagi-Uda antenna.

Define fading w.r.t. wave propagation.

Description : Define fading w.r.t. wave propagation. 

Last Answer : Fading: The fluctuation in signal strength at a receiver, which is mainly due to the interference of two waves which left the same source but arrived at the destination by different paths, is known as fading. 

Compare AM with FM with respect to following points: a) Definition. b) Modulation index. c) Bandwidth. d) Side band.

Description : Compare AM with FM with respect to following points: a) Definition. b) Modulation index. c) Bandwidth. d) Side band.

Last Answer : Parameters AM FM Definition It is the process in which the amplitude of carrier signal is varied in accordance with the instantaneous value of modulating signal keeping frequency and ... frequency deviation. Side band There are two sidebands Infinite number of sideband

When is Mono FM Band launched ?

Description : When is Mono FM Band launched ?

Last Answer : Mono FM band was started in 1948.

When did the stereo FM band start ?

Description : When did the stereo FM band start ?

Last Answer : Stereo FM band was introduced in 1970.

One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Last Answer : B. Phase control

Which of the following filters block FM radio band for TV channels (2 to 13)? A. High-pass filter B. Band reject filter C. Low-pass filter D. Band-pass filter

Description : Which of the following filters block FM radio band for TV channels (2 to 13)? A. High-pass filter B. Band reject filter C. Low-pass filter D. Band-pass filter

Last Answer : B. Band reject filter

The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Description : The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Last Answer : B. 120 kHz

Compare narrow band FM with wide band FM.

Description : Compare narrow band FM with wide band FM.

Last Answer : Narrow band FM Wide band FM 1 .Modulation Index is less than or slightly greater than 1.  1. Modulation Index is greater than 1.  2.Maximum deviation is ... .Application:-FM mobile communication like police wireless, ambulance etc. 5. Application:-Entertainment broadcasting.

If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be

Description :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

Last Answer :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be Distorted 

Define modulation index in FM. What is maximum value of deviation ratio.

Description : Define modulation index in FM. What is maximum value of deviation ratio.

Last Answer : Modulation Index of FM: It is defined as the ratio of Frequency Deviation (δ) to the modulating signal frequency (fm). (OR)  

Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Last Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Last Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

How were you affected by the MW/NE Blackout of Aug. 14, 2003?

Description : How were you affected by the MW/NE Blackout of Aug. 14, 2003?

Last Answer : in the dark ,sorry lol

10 parts per billion ozone (MW=48) equals how much ozone in ug/m3?

Description : 10 parts per billion ozone (MW=48) equals how much ozone in ug/m3?

Last Answer : Is this your homework????

What is equal to 1 MW ?

Description : What is equal to 1 MW ?

Last Answer : 1 MW = 10000 watts.

How do you compute mw to mwh?

Description : How do you compute mw to mwh?

Last Answer : Feel Free to Answer

what gov. grant is available for solar farm 1 to 5 MW?

Description : what gov. grant is available for solar farm 1 to 5 MW?

Last Answer : what gov. grants are available for solar farm 1 to 5 MW

Where is Tala Hydroelectric project, which is expected to generate 1020 MW power, located? (1) Arunachal Pradesh (2) Bhutan (3) Nepal (4) Himachal Pradesh

Description : Where is Tala Hydroelectric project, which is expected to generate 1020 MW power, located? (1) Arunachal Pradesh (2) Bhutan (3) Nepal (4) Himachal Pradesh

Last Answer : (2) Bhutan Explanation: Tala Hydroelectricity project is the biggest hydroelectric joint project between India and Bhutan so far, generating 4865 GWh/yr. Tala is located in Chukha Dzongkhag in western ... planned for June 2005, but because of geological problems this was delayed until March 2007.

In measuring crosstalk using dBx unit the reference power is A. 1 mW B. 1 W C. 1 pW D. 6 mW

Description : In measuring crosstalk using dBx unit the reference power is A. 1 mW B. 1 W C. 1 pW D. 6 mW

Last Answer : C. 1 pW

Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Description : Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Last Answer : A. 0.871 μW

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

ECE Board Exam March 1996 The power of standard test tone is normally ____________. A. 1 dB B. 0 mW C. 1 mW D. 1 W

Description : ECE Board Exam March 1996 The power of standard test tone is normally ____________. A. 1 dB B. 0 mW C. 1 mW D. 1 W

Last Answer : C. 1 mW

Nuclear power generation capacity in India is (A) 3000 MW (B) 10000 MW (C) More than hydroelectric power generation capacity (D) More than thermal power generation capacity

Description : Nuclear power generation capacity in India is (A) 3000 MW (B) 10000 MW (C) More than hydroelectric power generation capacity (D) More than thermal power generation capacity

Last Answer : (A) 3000 MW

Bhabha Atomic Research Centre (BARC) located at Trombay (near Bombay, INDIA) has (A) Five operating research reactors (namely Apsara, Cirus Zerelina, Purnima and Dhurva) (B) A 420 MW nuclear power plant (C) A very large capacity (100 tons/yr) heavy water plant (D) All (A), (B) and (C)

Description : Bhabha Atomic Research Centre (BARC) located at Trombay (near Bombay, INDIA) has (A) Five operating research reactors (namely Apsara, Cirus Zerelina, Purnima and Dhurva) (B) A 420 MW nuclear power plant (C) A very large capacity (100 tons/yr) heavy water plant (D) All (A), (B) and (C)

Last Answer : (A) Five operating research reactors (namely Apsara, Cirus Zerelina, Purnima and Dhurva)

Tarapur (INDIA) atomic power station (A) Has two boiling water reactors of American design (B) Has an installed capacity of 400 MW (C) Is the first power reactor in India, which became critical in 1969 (D) All (A), (B) and (C)

Description : Tarapur (INDIA) atomic power station (A) Has two boiling water reactors of American design (B) Has an installed capacity of 400 MW (C) Is the first power reactor in India, which became critical in 1969 (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Among which locomotive steam engines have the highest efficiency? a) 1 MW b) 2 MW c) 30 MW d) 660 MW

Description : Among which locomotive steam engines have the highest efficiency? a) 1 MW b) 2 MW c) 30 MW d) 660 MW

Last Answer : d) 660 MW

A cylinder contains oxygen at a pressure of 10 atm and a temperature of 300 K. The volume of the cylinder is 10 liters. What is the mass of the oxygen in grams? Molecular weight (MW) of oxygen is 32 g/mole?  a. 125.02  b. 130.08  c. 135.05  d. 120.04

Description : A cylinder contains oxygen at a pressure of 10 atm and a temperature of 300 K. The volume of the cylinder is 10 liters. What is the mass of the oxygen in grams? Molecular weight (MW) of oxygen is 32 g/mole?  a. 125.02  b. 130.08  c. 135.05  d. 120.04

Last Answer : 130.08 {(10atm)(10)(32)/(0.0821) (300K)}

A 0.064 kg of octane vapor (MW = 114) is mixed with0.91 kg of air (MW = 29.0) in the manifold of an Engine. The total pressure in the manifold is 86.1 kPa, and a temperature is 290 K. assume octane behaves ideally. What is the partial pressure of the air in the mixture in KPa?  a. 46.8  b. 48.6  c. 84.6  d. 64.8

Description : A 0.064 kg of octane vapor (MW = 114) is mixed with0.91 kg of air (MW = 29.0) in the manifold of an Engine. The total pressure in the manifold is 86.1 kPa, and a temperature is 290 K. assume octane behaves ideally. What is ... of the air in the mixture in KPa?  a. 46.8  b. 48.6  c. 84.6  d. 64.8

Last Answer : 84.6

For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Last Answer : ∙ C. -35 dBm

The electrical power unit Giga Watt (GW) may be written as a) 1,000,000 MW b) 1,000 MW c) 1,000 kW d) 1,000,000 W

Description : The electrical power unit Giga Watt (GW) may be written as a) 1,000,000 MW b) 1,000 MW c) 1,000 kW d) 1,000,000 W

Last Answer : b) 1,000 MW