Description : The process of breaking up a liquid into fine droplets by spraying is called a. vaporization b. carburetion c. injection d. atomization
Last Answer : ANSWER d. atomization
Description : What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above
Last Answer : ANSWER : B
Description : The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid
Last Answer : Ans: b
Description : The changing of solid directly to vapor without passing through liquid state is called a. Evaporation b. Vaporization c. Sublimation d. Condensation
Last Answer : Sublimation
Description : Vapour lock is a. complete or partial stoppage of fuel supply due to vaporization of the fuel b. locking of carburetor due to high vapor pressure c. excess fuel supply to the engine d. supply of liquid fuel to the engine
Last Answer : ANSWER a. complete or partial stoppage of fuel supply due to vaporization of the fuel
Description : Atomization of spray fluid can achieved by : A. discharging the liquid through an orifice under pressure B. by breaking up the jet of liquid by a blast of _____ C. both A & B D. none
Last Answer : C. both A & B
Description : At lower temperatures and pressures, the latent heat of vaporization of a refrigerant (a) decreases (b) increases (c) remains same (d) depends on other factors
Description : Alcohols alone cannot be used in CI engines as a) their self ignition temperature is high b) latent heat of vaporization is high c) all of the mentioned d) none of the mentioned
Last Answer : Answer: c Explanation: None.
Description : What is defined as the direct conversion of a substance from the solid to the vapor state or vice versa without passing the liquid state? A. Condensation B. Vaporization C. Sublimation D. Cryogenation
Description : The change of a gas to a liquid is called: w) vaporization x) sublimation y) condensation z) freezing
Last Answer : ANSWER: Y -- CONDENSATION
Description : Air can be cooled and dehumidified by A. circulating chilled water in tube across air flow B. placing evaporator coil across air flow C. spraying chilled water to air D. all of the mentioned
Last Answer : ANSWER : D
Description : If one or more nozzles are not spraying correctly then ________________ occurs. a) dripping b) misfiring c) cold firing d) none of the mentioned
Last Answer : Answer: b Explanation: If one or more nozzles are not spraying correctly then misfiring occurs and not cold firing.
Description : When a gas turns into a liquid the process is called: A. Condensation B. Evaporation C. Deposition D. Sublimation
Last Answer : ANSWER: A
Description : What refers to the amount of energy absorbed or released during a phase-change process? A. Molar heat B. Latent heat C. Vaporization heat D. Condensation heat
Last Answer : Latent heat
Description : A (n) ______printer works by spraying tiny droplets of ink onto the paper: a) ink - jet b) laser c) thermal d) None of The Above
Last Answer : a) ink - jet
Description : The heat absorbed by a unit mass of a material at its holding point in order to convert the material into a gas at the same temperature. a. Latent Heat of Sublimation b. Latent Heat of Vaporization c. Latent Heat of Fusion d. Latent Heat Of Condensation
Last Answer : Latent Heat of Vaporization
Description : On the pressure-enthalpy diagram, condensation and de-superheating is represented by a horizontal line because theprocess (a) takes place at constant pressure (b) takes place at constant temperature (c) takes place at constant entropy (d) takes place at constant enthalpy
Last Answer : Ans: a
Description : When air passes through silica gel, A. it absorbs water vapour molecules B. latent heat of condensation is released C.dbt of air increases D. all of the mentioned
Description : Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.
Last Answer : Ans: d
Description : The advantage of dry compression is that (a) it permits higher speeds to be used (b) it permits complete evaporation in the evaporator (c) it results in high volumetirc and mechanical efficiency (d) all of the above
Description : For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should ... tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used
Last Answer : Ans: c
Description : When the rate of evaporation of water is zero, the relative humidity of the air is A. 0% B. 100% C. 50% D. unpredictable
Description : Condensation is the reverse of – (1) Vaporization (2) Smog (3) Cirrus cloud (4) Fog
Last Answer : (1) Vaporization Explanation: Condensation is the change of physical state of matter from gaseous phase into liquid phase and is the reverse of vaporization. When the relative humidity reaches 100 per cent, the air is completely saturated. The air temperature is said to be as dew-point.
Description : Condensation is the reverse of (1) Vaporization (2) Smog (3) Cirrus cloud (4) Fog
Last Answer : Vaporization
Description : The loss of water by plants in the form of vapor i called: a) evaporation b) transpiration c) evapotranspiration d) vaporization
Last Answer : ANSWER: C -- evapotranspiration
Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface
Last Answer : (D) Boiling of a liquid on a hot surface
Description : ____ is when water goes from a solid to a gas without passing through the liquid phase. a. Transfusion c. Evaporation b. Sublimation d. Condensation
Last Answer : b. Sublimation
Description : .In Hydraulic sprayers, the degree of atomization is primarily a function of A. Liquid pressure and the nozzle characteristics B. Air velocity C. Size of the nozzle D. Size and shape of the atomizer
Last Answer : A. Liquid pressure and the nozzle characteristics
Description : The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature
Last Answer : Answer: d Explanation: The air inlet temperature sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength whereas the engine temperature sensor senses the ... gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.
Description : Which of the following procedures should be used to maintain a large electric motor during periods of inactivity? A. A thin layer of air-drying varnish should be applied on the windings. B. ... periodically to remove carbon dust. D. Space heaters should be used to prevent condensation of moisture.
Last Answer : Answer: D
Description : Process through which plants reproduce – (1) Pollination (2) Condensation (3) Eating (4) Evaporation
Last Answer : (1) Pollination Explanation: Pollination is the process by which pollen is transferred from the anther (male part) to the stigma (female part) of the plant, thereby enabling fertilization and reproduction. This takes place in the angiosperms, the flower bearing plants.
Description : Change of state namely evaporation condensation, freezing and melting is an __________ process. (A) Isothermal (B) Adiabatic (C) Isobaric (D) Isochoric
Last Answer : (A) Isothermal
Description : Which of the following exemplifies an adiabatic process? (A) Melting of ice (B) Condensation of alcohol vapor (C) Sudden bursting of a cycle tube (D) Evaporation of water
Last Answer : C) Sudden bursting of a cycle tube
Description : Process through which plants reproduce (1) Pollination (2) Condensation (3) Eating (4) Evaporation
Last Answer : Pollination
Description : The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid
Description : Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer
Description : In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser
Description : In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect
Description : Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid
Description : One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve
Description : In refrigerator, liquid receiver is required between condenser and flow controlling device, if quantity of refrigerant for system is (a) less than 2 kg (b) more than or equal to 3.65 kg (c) more than 10 kg (d) there is no such consideration
Description : In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour
Description : Critical pressure of a liquid is the pressure (a) above which liquid will remain liquid (b) above which liquid becomes gas (c) above which liquid becomes vapour (d) above which liquid becomes solid
Description : In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve
Description : In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve
Description : Clapeyron equation is applicable for registration at (a) saturation point of vapour (b) saturation point of liquid (c) sublimation temperature (d) triple point.
Description : Which of the following is the lightest and most volatile liquid fuel A. diesel B. kerosene C. fuel oil D. gasoline