Draw a neat sketch of regenerative feed heating.

Draw a neat sketch of regenerative feed heating.
by

1 Answer

Answer :

Regenerative Feed Heating

image  

by

Related questions

Describe velocity compounding with neat sketch.

Description : Describe velocity compounding with neat sketch.

Last Answer : ii) Velocity Compounding: ✓ In velocity compounding arrangement of blades and nozzles are made as below; N-M-F-M Where; N = Nozzle M = Moving blade F =Fixed blade ✓ Steam ... are shown in figure. ✓ This method has advantage that the initial cost is low so its efficiency is low.

Describe with neat sketch working of natural draft cooling towers.

Description : Describe with neat sketch working of natural draft cooling towers.

Last Answer : Natural draft cooling tower: -In natural draught cooling tower, the circulation of air is produced by the pressure difference of air inside the tower and outside atmospheric air Hot cooling water falls down ... the pressure difference of air inside and outside of cooling tower (natural flow).

With neat sketch describe working of reaction turbine.

Description : With neat sketch describe working of reaction turbine.

Last Answer : Working principle of reaction turbine- -A turbine in which steam pressure decreases gradually while expanding through the moving as well as through the fixed blade is known as reaction turbine. -In pure ... the steam to leave the moving blade as higher velocity than as which it entered.

Apart from feed heating, what should a plant have to obtain a gain in thermal efficiency? a) Lubrication b) Differential heating c) Reheating cycles d) Regenerative cycles

Description : Apart from feed heating, what should a plant have to obtain a gain in thermal efficiency? a) Lubrication b) Differential heating c) Reheating cycles d) Regenerative cycles

Last Answer : c) Reheating cycles

Describe anyone safety mounting used in boilers with sketch.

Description : Describe anyone safety mounting used in boilers with sketch.

Last Answer : Boiler Mounting : Fusible Plug Function:  It is very important safety device of a steam boiler, which protects the fire tube boiler against overheating. Location:  It is located just above ... hollow gun became open, the steam rushes into the furnace and puts out the fire (stop). 

In a refrigeration cycle, the super heating……..C.O.P (a)decreases (b)does not change (c) increases (d)none of the above

Description : In a refrigeration cycle, the super heating……..C.O.P (a)decreases (b)does not change (c) increases (d)none of the above

Last Answer : Ans: a

An important characteristic of absorption system of refrigeration is (a) noisy operation (b) quiet operation (c) very little power consumption (d) its input only in the form of heating.

Description : An important characteristic of absorption system of refrigeration is (a) noisy operation (b) quiet operation (c) very little power consumption (d) its input only in the form of heating.

Last Answer : Ans: D

Dew point can be best defined as the: a. Absolute temperature at which air, upon heating, will evaporate moisture b. . Percentage of moisture that air can hold at a given temperature and pressure c. . Temperature that air will begin to evaporate moisture d. . Temperature at which air, upon cooling, becomes saturated, causing moisture to condense should the temperature drop further e. . Atmospheric pressure at which air will condense moisture

Description : Dew point can be best defined as the: a. Absolute temperature at which air, upon heating, will evaporate moisture b. . Percentage of moisture that air can hold at a given temperature ... to condense should the temperature drop further e. . Atmospheric pressure at which air will condense moisture

Last Answer : Answer: D

The horizontal line in psychrometric chart joining the change of state of air represents A. humidification B. sensible cooling or heating C. sensible cooling or heating with humidification D. sensible cooling or heating with dehumidification

Description : The horizontal line in psychrometric chart joining the change of state of air represents A. humidification B. sensible cooling or heating C. sensible cooling or heating with humidification D. sensible cooling or heating with dehumidification

Last Answer : ANSWER : B

When, H1 = Total heat of air entering the coil (heating or cooling) H2 = Total heat of air leaving the coil (heating or cooling) H3 = Total heat of air at the end of the process (humidification or dehumidification) then, the sensible heat factor (H2 – H1) / (H3 – H1) represents the process of A. cooling and humidification B. cooling and dehumidification C. heating and humidification D. heating and dehumidification

Description : When, H1 = Total heat of air entering the coil (heating or cooling) H2 = Total heat of air leaving the coil (heating or cooling) H3 = Total heat of air at the end of ... A. cooling and humidification B. cooling and dehumidification C. heating and humidification D. heating and dehumidification

Last Answer : ANSWER : C

Heating and humidification is done in A. summer air conditioning B. winter air conditioning C. both of the mentioned D. none of the mentioned

Description : Heating and humidification is done in A. summer air conditioning B. winter air conditioning C. both of the mentioned D. none of the mentioned

Last Answer : ANSWER : B

In sensible heating or cooling, A. work done remains constant B. dry bulb temperature or air remains constant C. both of the mentioned D. none of the mentioned

Description : In sensible heating or cooling, A. work done remains constant B. dry bulb temperature or air remains constant C. both of the mentioned D. none of the mentioned

Last Answer : ANSWER : A

The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging

Description : The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging

Last Answer : ANSWER : D

The heating value per unit volume of hydrogen gas is less than ______________ that of air. a) 1/12th b) 1/10th c) 2/3rd d) 1/3rd

Description : The heating value per unit volume of hydrogen gas is less than ______________ that of air. a) 1/12th b) 1/10th c) 2/3rd d) 1/3rd

Last Answer : Answer: d Explanation: None

By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Description : By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Last Answer : Ans : d

Which one of the following methods can be adopted to obtain isothermal compression in an air compressor? A. Increasing the weight of the compressor B. Inter-stage heating C. Atmospheric cooling D. Providing appropriate dimensions to the cylinder

Description : Which one of the following methods can be adopted to obtain isothermal compression in an air compressor? A. Increasing the weight of the compressor B. Inter-stage heating C. Atmospheric cooling D. Providing appropriate dimensions to the cylinder

Last Answer : ANSWER : A

All heat engines utilize a. lower heating value of oil b. higher heating value of oil c. net calorific value of oil d. calorific value of fuel

Description : All heat engines utilize a. lower heating value of oil b. higher heating value of oil c. net calorific value of oil d. calorific value of fuel

Last Answer : ANSWER a. lower heating value of oil

Compressor at high altitude will draw A. More power B. Less power C. Same power D. Unpredictable

Description : Compressor at high altitude will draw A. More power B. Less power C. Same power D. Unpredictable

Last Answer : ANSWER : B

Draw Lamont Boiler. Label the components and discuss the working and construction.

Description : Draw Lamont Boiler. Label the components and discuss the working and construction. 

Last Answer : 1. This is a modern high pressure, water tube boiler working on a forced circulation. 2. The circulation is maintained by a centrifugal pump, driven by a steam turbine, using steam from the ... required application. Lamont boilers generates 45 to 50 tones steam per hour at 130 bar with 5000 C.

Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Description : Draw a neat sketch and explain the use of CT and PT for measurement of power in a single-phase circuit?

Last Answer : If wattmeter of proper range is not available or if voltage and current ranges are high we can usr CT and PT of suitable ratio. Connect the CT and PT as shown in figure. The reading of wattmeter can be multiplied by the ratio to get the actual power.   

Draw a neat sketch of Electro-dialysis.

Description : Draw a neat sketch of Electro-dialysis.

Last Answer : Electro- dialysis:

Draw a neat sketch of cross-section of an exogenous tree and label the parts.

Description : Draw a neat sketch of cross-section of an exogenous tree and label the parts. 

Last Answer : Cross-section of an exogenous tree:

Draw neat labeled sketch of ply press.

Description : Draw neat labeled sketch of ply press.

Last Answer : sketch of ply press

Draw the neat sketch of overhead valve operating mechanism and explain its working.

Description : Draw the neat sketch of overhead valve operating mechanism and explain its working.

Last Answer : Overhead valve mechanism: Figure shows the valve mechanism to operate the valve when it is in the cylinder head (in I and F head design). This type of mechanism requires two additional moving parts the push ... close. A spring (attached to the valve) returns the valve to its seated position.   

Draw neat sketch of valve timing diagram for 4-stroke petrol engine & label it.

Description : Draw neat sketch of valve timing diagram for 4-stroke petrol engine & label it.

Last Answer : Figure: Valve timing diagram of 4 stroke SI engine  

(i) state any two applications of I. C. Engine (ii) Draw a neat sketch of Two stroke petrol engine.

Description : (i) state any two applications of I. C. Engine (ii) Draw a neat sketch of Two stroke petrol engine.

Last Answer : Applications of I.C engine 1) In Automotive - i) Two stroke engine - Mopeds, Scooters. ii) Four stroke engine - Light vehicles, Heavy vehicles. 2) Marine Application - Ships, Boat 3) Locomotive s - ... handling system  (ii) Draw a neat sketch of Two stroke petrol engine. OR

Draw a neat lebelled sketch of optical square. Explain its working.

Description : Draw a neat lebelled sketch of optical square. Explain its working.

Last Answer : Working of optical square1. Optical square works on principle of optical square to set perpendicular offset 2. Keep ranging rods at point B and C as shown in fig. 3. Observe the ... matched each other point D can be marked on ground and distance CD is measured as perpendicular offset.

Draw a neat sketch of an arrow with dimensions.

Description : Draw a neat sketch of an arrow with dimensions.

Last Answer :  neat sketch of an arrow with dimensions

Draw a neat labeled sketch of 30m chain.

Description : Draw a neat labeled sketch of 30m chain.

Last Answer : neat labeled sketch of 30m chain

Draw a neat sketch of optical square. Explain its working.

Description : Draw a neat sketch of optical square. Explain its working.

Last Answer : Optical Square: Working: The optical square consists of circular box 50 mm in diameter, 12.5 mm in depth. The box has three slits as A,B, and C. bb' is horizon glass, half silvered i.e ... the point on the chain line where the offset can be dropped to meet point J as shown in fig.  

Draw a neat sketch of prismatic compass and label its component parts

Description : Draw a neat sketch of prismatic compass and label its component parts

Last Answer : Sketch of prismatic compass and label its component parts

Draw neat sketch of pre-combustion chamber and name its parts.

Description : Draw neat sketch of pre-combustion chamber and name its parts.

Last Answer : Fig. Pre-combustion chamber

Draw neat sketch to show TBI system of SI engine and name its parts.

Description : Draw neat sketch to show TBI system of SI engine and name its parts.

Last Answer : Draw neat sketch to show TBI system of SI engine and name its parts.

State the different types of SI engine combustion chambers. Draw a neat sketch of any one.

Description : State the different types of SI engine combustion chambers. Draw a neat sketch of any one.

Last Answer : 1) T Head Type Combustion chambers 2) L Head Type Combustion chambers 3) F- Head combustion chamber 4) Over head valve or I head combustion chamber 5) Hemispherical combustion chamber 6) Bathtub ... - Head combustion chamber 4) Over head valve or I head combustion chamber

Draw neat sketch of swirl type combustion chamber of IDI engine.

Description : Draw neat sketch of swirl type combustion chamber of IDI engine.

Last Answer : Fig. swirl type combustion chamber of IDI engine.

Define folds and draw neat sketch of a fold and label its different parts.

Description : Define folds and draw neat sketch of a fold and label its different parts. 

Last Answer : Fold: Folds may be defined as undulations or bends that are developed in the rock of the Earth’s crust, as a result of stresses (commonly lateral compression) To which these rocks have been subjected to, from time to time in the past history of the Earth.

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics

Draw a neat sketch of simple curve showing all elements.

Description : Draw a neat sketch of simple curve showing all elements.

Last Answer : Simple curve

Draw neat sketch of simple circular curve and show notation there on.

Description : Draw neat sketch of simple circular curve and show notation there on.

Last Answer : Sketch of simple circular curve and show notation there on :

Draw neat sketch of contour for the following i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line

Description : Draw neat sketch of contour for the following i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line 

Last Answer : i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line 

Draw a neat sketch of progressive die.

Description : Draw a neat sketch of progressive die. 

Last Answer : progressive die

Draw neat sketch showing various parts of die set.

Description : Draw neat sketch showing various parts of die set. 

Last Answer : Answer: 1. Stop 2.Sheet metal 3.Pilot 4.Blanking punch 5.Ram 6.Piercing punch 7.Stripper 8.die Fig. Progressive Die OR

Draw neat sketch of compound die, showing various parts of it.

Description : Draw neat sketch of compound die, showing various parts of it.

Last Answer : Answer:

Draw the neat sketch of fly press. Give the functions of important parts of it.

Description : Draw the neat sketch of fly press. Give the functions of important parts of it. 

Last Answer : Answer: OR Functions of important parts of Fly Press. 1. Ram : This is main operating part of the press which works directly during processing of a workpiece. Ram ... : A die is a specialized tool used in manufacturing industries to cut or shape material mostly using a press 

Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Last Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Draw a neat sketch of Ultrasonic flowmeter.

Description : Draw a neat sketch of Ultrasonic flowmeter. 

Last Answer : Diagram of ultrasonic flow meter (Time Difference Type ):

Draw neat sketch of Rotameter and explain its working principle.

Description : Draw neat sketch of Rotameter and explain its working principle.

Last Answer : Rotameter: - A variable-area flowmeter is one where the fluid must pass through a restriction whose area increases with flow rate. The height of the float is directly proportional to the flowrate ... on glass tube and the flow rate can be determined by direct observation of the metering tube  

(i) Draw the neat sketch of bomb calorimeter. (ii) Write any three sources of air leakage in steam condenser.

Description : (i) Draw the neat sketch of bomb calorimeter. (ii) Write any three sources of air leakage in steam condenser.

Last Answer : (i)   (ii) Sources of air leakage in condenser: i) Air leak through joints and packing. ii) Air also comes in condenser with the steam. iii) In jet condensers dissolved air in the cooling water enters the condenser. 

Draw neat labelled sketch of Lamont boiler.

Description : Draw neat labelled sketch of Lamont boiler. 

Last Answer : Lamont boiler