Is a lightning conductor near high voltage wires necessary?

I have a cottage about 100 meters from high voltage wires. Is it possible that he will hit me during a storm if I don't have a lightning conductor? It would lead to those wires, wouldn't it?
by

1 Answer

Answer :

Sometimes the lightning must go; On the other hand, lightning is a discharge of such high voltage and so high currents that it can easily beat even the cottage 100 m away. Personally, I would like a lightning rod to the cottage. Rather than masons, I would entrust the installation of lightning conductors to electricians ... ;-) In any case, the installation of lightning conductors should include inspection (by an inspection technician), the service interval for subsequent inspections is 5 years.
by

Related questions

Which of the following statements is incorrect? (a) Station batteries are used to operate relay only (b) The lightning arresters are basically surge diverters (c) An impedance relay has maximum fault current when fault occurs near the relay (d) A high speed relay has an operation of 1 to 2 cycles

Description : Which of the following statements is incorrect? (a) Station batteries are used to operate relay only (b) The lightning arresters are basically surge diverters (c) An impedance relay has maximum fault current when fault occurs near the relay (d) A high speed relay has an operation of 1 to 2 cycles

Last Answer : (a) Station batteries are used to operate relay only

Is a lightning conductor set up on one of the semi-detached houses dangerous for the other without a lightning conductor?

Description : We live in a single-storey semi-detached house without a lightning conductor (it was built 60 years ago). It is a colony of semi-detached houses, built on a hill, about 20 m apart (uphill). The ... lightning. We will not agree on a joint construction with a neighbor (we do not have good relations).

Last Answer : If the semi-detached house does not have a common electrical installation, then there is no risk. It also has no effect on individual objects.

Is the building approved without a lightning conductor?

Last Answer : If the construction of a lightning conductor is in the construction documentation submitted for the issuance of a building permit, this is a condition. In one case, I managed to approve the ... the lightning conductor. However, it was a condition to rectify this shortcoming as soon as possible.

Where does the lightning conductor on the roof belong?

Description : Where is the lightning conductor located? The highest place on the construction site?

Last Answer : The collectors are placed at the highest points of the building - not only so that these points are also protected, but because the space protected by the collector has a conical shape - that is, to protect as much of the building as possible. So, for example, on the ridge of the roof.

To prevent damage from lightning, lightning conductors are used on tall structures. The lightning conductor – (1) should be made of a good conductor but can be of any shape (2) should be in the form of a vertical rod (3) can be of any shape (4) should be made of a good conductor like copper with sharp-pointed edges

Description : To prevent damage from lightning, lightning conductors are used on tall structures. The lightning conductor - (1) should be made of a good conductor but can be of any shape (2) should be in the form ... can be of any shape (4) should be made of a good conductor like copper with sharp-pointed edges

Last Answer : (4) should be made of a good conductor like copper with sharppointed edges Explanation: A lightning conductor is made up of a sharp pointed metal (usually copper metal, as it is a very good ... cloud, it will first strike the pointed tip of the lightning conductor and quickly travel to the earth.

To prevent damage from lightning, lightning conductors are used on tall structures. The lightning conductor (1) should be made of a good conductor but can be of any shape (2) should be in the form of a vertical rod (3) can be of any shape (4) should be made of a good conductor like copper with sharp-pointed edges

Description : To prevent damage from lightning, lightning conductors are used on tall structures. The lightning conductor (1) should be made of a good conductor but can be of any shape (2) should be in the form of ... can be of any shape (4) should be made of a good conductor like copper with sharp-pointed edges

Last Answer : should be made of a good conductor like copper with sharp-pointed edges

A lightning conductor on top of a building is made into a pointed spike because

Last Answer : A lightning conductor on top of a building is made into a pointed spike because Charge per unit area becomes very high for lightning to discharge.

The force between two long parallel wires A and B carrying current is `0.004 Nm^(-1)`. The conductors are 0.01 m apart. If the current in conductor A

Description : The force between two long parallel wires A and B carrying current is `0.004 Nm^(-1)`. The conductors are 0.01 m apart. If the current in conductor A

Last Answer : The force between two long parallel wires A and B carrying current is `0.004 Nm^(-1)`. The conductors are 0.01 m ... . `50 A ` C. `10 A` D. `100 A`

Copper wires are generally used for electrical power transmission instead of iron wire because (1) copper is cheaper than iron (2) copper is lighter than iron (3) copper is a better conductor of electricity than iron (4) copper can take higher power than iron

Description : Copper wires are generally used for electrical power transmission instead of iron wire because (1) copper is cheaper than iron (2) copper is lighter than iron (3) copper is a better conductor of electricity than iron (4) copper can take higher power than iron

Last Answer : (3) copper is a better conductor of electricity than iron Explanation: Copper is generally preferred for electrical power transmission instead of iron because of its high electrical conductivity and low resistivity.

Due to self-inductance, the coil wires are known as: a. Insulator b. Conductor c. Inductor d. Semi-conductor

Description : Due to self-inductance, the coil wires are known as: a. Insulator b. Conductor c. Inductor d. Semi-conductor

Last Answer : c. Inductor

Copper wires are generally used for electrical power transmission instead of iron wire because : (1) copper is cheaper than iron (2) copper is lighter than iron (3) copper is a better conductor of electricity than iron (4) copper can take higher power than iron

Description : Copper wires are generally used for electrical power transmission instead of iron wire because : (1) copper is cheaper than iron (2) copper is lighter than iron (3) copper is a better conductor of electricity than iron (4) copper can take higher power than iron 

Last Answer : copper is a better conductor of electricity than iron

Why the tooth wires and are they a sign of bad dental work or necessary?

Description : Why the tooth wires and are they a sign of bad dental work or necessary?

Last Answer : Sounds like what you speculated they are, part of a bridge. Don’t have bad dental habits, so you keep all your teeth or if teeth are pulled; get implants which screw in the jawbone and attaches a replacement Acrylic or Zircon tooth.

Which of the following devices will receive voltage surge first travelling on the transmission line ? (a) Lightning arresters (b) Relays (c) Step-down transformer (d) Switchgear

Description : Which of the following devices will receive voltage surge first travelling on the transmission line ? (a) Lightning arresters (b) Relays (c) Step-down transformer (d) Switchgear

Last Answer : (a) Lightning arresters

Can wires disturb radio quality voltage?

Description : I bought a new MP4 player and when I turn on the radio, it skips and makes noise (all stations). Could it be that trolleybus and tram wires run around the barracks? I would like to listen to it mainly at home in bed, but it makes a lot of fun. I haven't been anywhere outside the city yet.

Last Answer : the noise is probably not, but if it just skips when the collector crosses the crossing of the trolley and sparkles, then maybe it is, but it would have to be close enough, so under 50 m it will want ... cord cords, so there may be a fault there (or in plugging in the connector as it is not frayed)

A sqaure loop `ABCD`, carrying a current `I_(2)` is placed near and coplanar with a long straight conductor `XY`, carrying a current `I_(1)` as shwon

Description : A sqaure loop `ABCD`, carrying a current `I_(2)` is placed near and coplanar with a long straight conductor `XY`, carrying a current `I_(1)` as shwon

Last Answer : A sqaure loop `ABCD`, carrying a current `I_(2)` is placed near and coplanar with a long straight conductor `XY` ... )/(2pi)` D. `(2mu_(0)Ii)/(3pi)`

Fish can survive inside a frozen lake because (a) fish are warm blooded animals (b) fish hibernate in ice (c) water near the bottom does not freeze (d) ice is a good conductor of heat

Description : Fish can survive inside a frozen lake because (a) fish are warm blooded animals (b) fish hibernate in ice (c) water near the bottom does not freeze (d) ice is a good conductor of heat

Last Answer : Ans:(c)

Owing to skin effect (a) current flows through the half cross-section of the conductor (b) portion of the conductor near the surface carries more current and core of the conductor carries less current (c) portion of the conductor near the surface carries less current and core of the conductor carries more cur¬rent (d) any of the above (e) none of the above

Description : Owing to skin effect (a) current flows through the half cross-section of the conductor (b) portion of the conductor near the surface carries more current and core of the conductor carries less current (c) ... core of the conductor carries more cur¬rent (d) any of the above (e) none of the above

Last Answer : (b) portion of the conductor near the surface carries more current and core of the conductor carries less current

A bus bar is 3 inches wide and 0.375 inches thick. What size of round conductor (in circular mils) is necessary to carry the same current as the bus bar? A. 1,125,000 circular mils B. 1,250,000 circular mils C. 1,432,000 circular mils D. 1,547,000 circular mils

Description : A bus bar is 3 inches wide and 0.375 inches thick. What size of round conductor (in circular mils) is necessary to carry the same current as the bus bar? A. 1,125,000 circular mils B. 1,250,000 circular mils C. 1,432,000 circular mils D. 1,547,000 circular mils

Last Answer : Answer: C

Why do people find it necessary to come to a stop, or near stop, before turning into the turn lane?

Description : Why do people find it necessary to come to a stop, or near stop, before turning into the turn lane?

Last Answer : answer:My guess is that they are being safe. They don't know if opposing traffic from the right is making a left turn and might cut off part of the turn lane because of the angle of ... about being unsure of directions and decision making. Bottom line, there may be perfectly legit reasons. CHill.

Nichrome wire is used as a heating element I many appliances because (a) it can be drawn out into wires easily (b) it has high resistivity (c) it resists oxidation in air when red hot (d) both (b) and (c) are correct

Description : Nichrome wire is used as a heating element I many appliances because (a) it can be drawn out into wires easily (b) it has high resistivity (c) it resists oxidation in air when red hot (d) both (b) and (c) are correct

Last Answer : Ans:(d)

Ultimate strength of cold drawn high steel wires (A) Increases with increase in diameter of bar (B) Decreases with increase in diameter of bar (C) Does not depend on diameter of bar (D) None of the above

Description : Ultimate strength of cold drawn high steel wires (A) Increases with increase in diameter of bar (B) Decreases with increase in diameter of bar (C) Does not depend on diameter of bar (D) None of the above

Last Answer : Answer: Option B

Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength

Description : Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength

Last Answer : Answer: Option B

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

In the left hand rule, forefinger always represents (a) voltage (b) current (c) magnetic field (d) direction of force on the conductor

Description : In the left hand rule, forefinger always represents (a) voltage (b) current (c) magnetic field (d) direction of force on the conductor

Last Answer : (c) magnetic field

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

In a cable the voltage stress is maximum at (a) sheath (6) insulator (e) surface of the conductor (d) core of the conductor

Description : In a cable the voltage stress is maximum at (a) sheath (6) insulator (e) surface of the conductor (d) core of the conductor

Last Answer : (d) core of the conductor

PVC stands for (a) polyvinyl chloride (b) post varnish conductor (c) pressed and varnished cloth (d) positive voltage conductor (e) none of the above

Description : PVC stands for (a) polyvinyl chloride (b) post varnish conductor (c) pressed and varnished cloth (d) positive voltage conductor (e) none of the above

Last Answer : (a) polyvinyl chloride

The thickness of the layer of insulation on the conductor, in cables, depends upon (a) Reactive power (b) Power factor (c) Voltage (d) Current carrying capacity

Description : The thickness of the layer of insulation on the conductor, in cables, depends upon (a) Reactive power (b) Power factor (c) Voltage (d) Current carrying capacity

Last Answer : (c) Voltage

Is it considered safe for a person to touch any energized low-voltage conductor with the bare hand?

Description : Is it considered safe for a person to touch any energized low-voltage conductor with the bare hand?

Last Answer : NEVER! All energized electric circuits should be considered potentially dangerous.

Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Description : Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Last Answer : (b) short-circuit current of the system is increased

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

As the voltage of transmission increases, the volume of conductor (A) increases. (B) does not change. (C) decreases. (D) increases proportionately.

Description : As the voltage of transmission increases, the volume of conductor (A) increases. (B) does not change. (C) decreases. (D) increases proportionately.

Last Answer : Ans: C Decreases due to skin effect.

The size of a conductor used in power cables depends on the (A) operating voltage. (B) power factor. (C) current to be carried. (D) type of insulation used.

Description : The size of a conductor used in power cables depends on the (A) operating voltage. (B) power factor. (C) current to be carried. (D) type of insulation used.

Last Answer : (C) current to be carried.

Compare pin type and suspension insulators on given points: (i) Position of insulator on cross arm. (ii) Position of conductor on insulator. (iii) Reaction on cross arm. (iv) Possibility of flash over due to large birds (v) Maintenance/Replacement cost (vi) Maximum voltage level (vii) Effect on height of supporting structure. (viii) Life

Description : Compare pin type and suspension insulators on given points: (i) Position of insulator on cross arm. (ii) Position of conductor on insulator. (iii) Reaction on cross arm. (iv) Possibility of ... Replacement cost (vi) Maximum voltage level (vii) Effect on height of supporting structure. (viii) Life 

Last Answer : S.No  Points Pin Type insulator Suspension or Disc Type insulator 1 Position of insulator on cross arm It is fixed on top of cross arm by using galvanized steel pin. So it is ... so to maintain minimum ground clearance height of pole increase.  8 Life Less More

Upon increasing the transmission voltage, volume of the conductor will:...

Description : Upon increasing the transmission voltage, volume of the conductor will:  (A) increase (B) not change (C) decrease (D) increase for some time and then decrease

Last Answer : Upon increasing the transmission voltage, volume of the conductor will: decrease

One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for polarity using a/an ____________. A. iron bar across each field B. magnetic compass placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Description : One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for ... placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Last Answer : Answer: B

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

In transformers, why the low voltage winding is placed near the core?

Description : In transformers, why the low voltage winding is placed near the core?

Last Answer : The winding & Core are both made of metals and so an insulation have to be placed in between them, the thickness of insulation depends on the voltage rating of the winding. In order to reduce the insulation requirement the low voltage winding place near the core.

Where the voltage node of a half-wave antenna does exists? A. At feed point B. Near the center C. At center D. Near the feed point

Description : Where the voltage node of a half-wave antenna does exists? A. At feed point B. Near the center C. At center D. Near the feed point

Last Answer : A. At feed point

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

In a transformer, low voltage winding is placed near the core in case of concentric windings so

Description : In a transformer, low voltage winding is placed near the core in case of concentric windings so as to  1. Reduce the leakage flux 2. Reduce the insulation requirement 3. Reduce the risk of voltage shock in case of insulation breakdown 4. Reduce the ... a) 1, 2, 3 (b) 2, 3, 4 (c) 1, 2, 3, 4 (d) 2, 3

Last Answer : In a transformer, low voltage winding is placed near the core in case of concentric windings so as to  1. Reduce the leakage flux 2. Reduce the insulation requirement 3. Reduce the risk of voltage shock in case of insulation breakdown 4. Reduce ... ) 1, 2, 3 (b) 2, 3, 4 (c) 1, 2, 3, 4 (d) 2, 3

Periodic testing of circuit breakers is necessary to assure that a correctly rated and properly installed unit _________________. A. can trip faster as it increases in age B. will continue to provide the original degree of protection C. does not exceed its interrupting capacity D. be able to withstand at least 125% of applied voltage

Description : Periodic testing of circuit breakers is necessary to assure that a correctly rated and properly installed unit _________________. A. can trip faster as it increases in age B. will continue to provide ... not exceed its interrupting capacity D. be able to withstand at least 125% of applied voltage

Last Answer : Answer: B

The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the throttle control circuit B. feedback resistor of the summing amplifier circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Last Answer : Answer: A

What are the necessary tests to determine the efficiency, voltage regulation, and temperature rise of winding & insulation of transformer?

Description : What are the necessary tests to determine the efficiency, voltage regulation, and temperature rise of winding & insulation of transformer?

Last Answer : 1.Direct loading test 2.Open circuit test 3. Short circuit test 4. Sumpner's or back to back test

A commutator in a d.c. machine (A) Reduces power loss in armature. (B) Reduces power loss in field circuit. (C) Converts the induced a.c armature voltage into direct voltage. (D) Is not necessary.

Description : A commutator in a d.c. machine (A) Reduces power loss in armature. (B) Reduces power loss in field circuit. (C) Converts the induced a.c armature voltage into direct voltage. (D) Is not necessary.

Last Answer : Ans: C As name suggests, it commutes ac into dc.

To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Description : To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Last Answer : To determine the polarity of the voltage drop across a resistor, it is necessary to know direction of current through the resistor.

Have you ever felt lightning move through your body?

Description : Have you ever felt lightning move through your body?

Last Answer : No. But I’ve won the lottery once.