Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength

Which of the following has high tensile strength?
(A) Plain hot rolled wires
(B) Cold drawn wires
(C) Heat treated rolled wires
(D) All have same tensile strength
by

1 Answer

Answer :

Answer: Option B
by

Related questions

Ultimate strength of cold drawn high steel wires (A) Increases with increase in diameter of bar (B) Decreases with increase in diameter of bar (C) Does not depend on diameter of bar (D) None of the above

Description : Ultimate strength of cold drawn high steel wires (A) Increases with increase in diameter of bar (B) Decreases with increase in diameter of bar (C) Does not depend on diameter of bar (D) None of the above

Last Answer : Answer: Option B

As per IS:1139, the characteristic yield strength for hot rolled High yield strength deformed bars is [ A ] 250 N/mm2 [ B ] 415 N/mm2 [ C ] 500 N/mm2 [ D ] 550 N/mm2

Description : As per IS:1139, the characteristic yield strength for hot rolled High yield strength deformed bars is [ A ] 250 N/mm2 [ B ] 415 N/mm2 [ C ] 500 N/mm2 [ D ] 550 N/mm2

Last Answer : [ B ] 415 N/mm2

Nichrome wire is used as a heating element I many appliances because (a) it can be drawn out into wires easily (b) it has high resistivity (c) it resists oxidation in air when red hot (d) both (b) and (c) are correct

Description : Nichrome wire is used as a heating element I many appliances because (a) it can be drawn out into wires easily (b) it has high resistivity (c) it resists oxidation in air when red hot (d) both (b) and (c) are correct

Last Answer : Ans:(d)

Pipes for bi-cycle frames are made of __________ steel. (A) Hot rolled (B) Chrome carbon (C) Cold rolled (D) Stainless

Description : Pipes for bi-cycle frames are made of __________ steel. (A) Hot rolled (B) Chrome carbon (C) Cold rolled (D) Stainless

Last Answer : (C) Cold rolled

The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending strength and axial yield strength of material (c) Buckling strength based on the net area of the section and percentage elongation at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Description : Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Last Answer : (a) Compressive stress.

Raw water treated with only chlorine, is known as (A) Plain chlorination (B) Pre-chlorination (C) First-chlorination (D) De-chlorination

Description : Raw water treated with only chlorine, is known as (A) Plain chlorination (B) Pre-chlorination (C) First-chlorination (D) De-chlorination

Last Answer : (A) Plain chlorination

Elastomers are (A) Thermosetting material (B) Exemplified by protein derivatives (C) Having high flexural strength (D) Having very high tensile strength and heat resistance

Description : Elastomers are (A) Thermosetting material (B) Exemplified by protein derivatives (C) Having high flexural strength (D) Having very high tensile strength and heat resistance

Last Answer : (C) Having high flexural strength

Plywood has the advantage of (A) Greater tensile strength in longer direction (B) Greater tensile strength in shorter direction (C) Same tensile strength in all directions (D) None of the above

Description : Plywood has the advantage of (A) Greater tensile strength in longer direction (B) Greater tensile strength in shorter direction (C) Same tensile strength in all directions (D) None of the above

Last Answer : Answer: Option C

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

Aluminium alloy is one of the most suitable materials of construction for aircrafts mainly due to its (A) High strength to weight ratio (B) Low temperature strength properties (C) Its ability to be cast, rolled, forged & stamped (D) High strength and corrosion & oxidation-resistance at elevated temperature

Description : Aluminium alloy is one of the most suitable materials of construction for aircrafts mainly due to its (A) High strength to weight ratio (B) Low temperature strength properties (C) Its ability ... rolled, forged & stamped (D) High strength and corrosion & oxidation-resistance at elevated temperature

Last Answer : (A) High strength to weight ratio

Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Description : Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Last Answer : Option B

In a pre-stressed member it is advisable to use (A) Low strength concrete only (B) High strength concrete only (C) Low strength concrete but high tensile steel (D) High strength concrete and high tensile

Description : In a pre-stressed member it is advisable to use (A) Low strength concrete only (B) High strength concrete only (C) Low strength concrete but high tensile steel (D) High strength concrete and high tensile

Last Answer : Answer: Option D

High carbon content in the steel causes (A) Decrease in tensile strength but increase in ductility (B) Increase in tensile strength but decrease in ductility (C) Decrease in both tensile strength and ductility (D) Increase in both tensile strength and ductility

Description : High carbon content in the steel causes (A) Decrease in tensile strength but increase in ductility (B) Increase in tensile strength but decrease in ductility (C) Decrease in both tensile strength and ductility (D) Increase in both tensile strength and ductility

Last Answer : Answer: Option B

Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Last Answer : Answer: Option D

Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Description : Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Last Answer : (b) low

In cold riveting like hot riveting shank is subjected to majorly tensile stress. a) True b) False

Description : In cold riveting like hot riveting shank is subjected to majorly tensile stress. a) True b) False

Last Answer : b) False

High purity nitrogen is used in (A) Making protective gas (95% N2 + 5% H2 ) for annealing of cold rolled steel strip coils (B) Fire fighting purposes (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : High purity nitrogen is used in (A) Making protective gas (95% N2 + 5% H2 ) for annealing of cold rolled steel strip coils (B) Fire fighting purposes (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Non-metals cannot be drawn into wires. Why ? [DAV2008] -Science

Description : Non-metals cannot be drawn into wires. Why ? [DAV2008] -Science

Last Answer : Non-metals are not ductile, therefore they cannot be drawn into wires.

`1kg` piece of copper is drawn into a wire `1mm` thick and another piece into a wire `2mm` thick. Compare the resistance of these wires.

Description : `1kg` piece of copper is drawn into a wire `1mm` thick and another piece into a wire `2mm` thick. Compare the resistance of these wires.

Last Answer : `1kg` piece of copper is drawn into a wire `1mm` thick and another piece into a wire `2mm` thick. Compare the resistance of these wires.

If a metal can be drawn into wires relatively easily it is called: (1) malleable (2) ductile (3) extractive (4) tactile

Description : If a metal can be drawn into wires relatively easily it is called: (1) malleable (2) ductile (3) extractive (4) tactile

Last Answer : (2) ductile Explanation: Ductility is a physical property of a material associated with the ability to be hammered thin or stretched into wire without breaking.

A material is called 'ductile', if it can be (A) Drawn into wires (B) Hammered to a thin sheet (C) Fractured without deformation (D) Made lustrous by heating it

Description : A material is called 'ductile', if it can be (A) Drawn into wires (B) Hammered to a thin sheet (C) Fractured without deformation (D) Made lustrous by heating it

Last Answer : (A) Drawn into wires

Property of material which allows it to be drawn out into wires is (A) Ductility. (B) Solder ability. (C) Super conductivity. (D) Malleability.

Description : Property of material which allows it to be drawn out into wires is (A) Ductility. (B) Solder ability. (C) Super conductivity. (D) Malleability.

Last Answer : (A) Ductility.

If a metal can be drawn into wires relatively easily it is called: w) malleable x) ductile y) extractive z) tactile

Description : If a metal can be drawn into wires relatively easily it is called: w) malleable x) ductile y) extractive z) tactile

Last Answer : ANSWER: X -- DUCTILE

The property of materials by which they can be drawn into wires is known as:

Description : The property of materials by which they can be drawn into wires is known as: A) malleability B) elasticity C) creep D) ductility

Last Answer : The property of materials by which they can be drawn into wires is known as: ductility

Styrene butadiene rubber (SBR) as compared to natural rubber has (A) Poor tensile strength (B) Poorer resistance (C) Greater amount of heat build up heavy loading (D) All (A), (B) and (C)

Description : Styrene butadiene rubber (SBR) as compared to natural rubber has (A) Poor tensile strength (B) Poorer resistance (C) Greater amount of heat build up heavy loading (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Styrene-butadiene-rubber (SBR) as compared to natural rubber has (A) Poorer tensile strength (B) Poorer resistance to oxidation (C) Greater amount of heat build-up under heavy loading (D) All (A), (B) and (C)

Description : Styrene-butadiene-rubber (SBR) as compared to natural rubber has (A) Poorer tensile strength (B) Poorer resistance to oxidation (C) Greater amount of heat build-up under heavy loading (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

At the liquid limit a) The soil just begins to crumble when rolled into a thread b) The shearing strength against flowing is negligible c) The shearing strength against flowing is a small but definite* d) The soil will not get fully saturated

Description : At the liquid limit a) The soil just begins to crumble when rolled into a thread b) The shearing strength against flowing is negligible c) The shearing strength against flowing is a small but definite* d) The soil will not get fully saturated

Last Answer : c) The shearing strength against flowing is a small but definite

Pick up the correct statement from the following: (A) Corrugated sheet iron is made by passing plain sheets between grooved rollers (B) Strength and stiffness of corrugated sheets are considerably increased (C) Corrugated sheets are generally used on slanting roofs (D) All the above

Description : Pick up the correct statement from the following: (A) Corrugated sheet iron is made by passing plain sheets between grooved rollers (B) Strength and stiffness of corrugated sheets are considerably increased (C) Corrugated sheets are generally used on slanting roofs (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

The relation between modulus of rupture fcr, splitting strength fcs and direct tensile strength fcl is given by (A) fcr - fcs = fcl (B) fcr > fcs > fcl (C) fcr < fcs < fcl (D) fcs > fcr > fcl

Description : The relation between modulus of rupture fcr, splitting strength fcs and direct tensile strength fcl is given by (A) fcr - fcs = fcl (B) fcr > fcs > fcl (C) fcr < fcs < fcl (D) fcs > fcr > fcl

Last Answer : Option B

For quality control of Portland cement, the test essentially done is (A) Setting time (B) Tensile strength (C) Consistency (D) All the above

Description : For quality control of Portland cement, the test essentially done is (A) Setting time (B) Tensile strength (C) Consistency (D) All the above

Last Answer : D

The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Description : The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Last Answer : Answer: Option B

A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Description : A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Last Answer : Answer: Option B

Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Description : Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Last Answer : Answer: Option A

Vicat apparatus is used for (A) Fineness test (B) Consistency test (C) Test for setting time (D) Test for tensile strength

Description : Vicat apparatus is used for (A) Fineness test (B) Consistency test (C) Test for setting time (D) Test for tensile strength

Last Answer : Answer: Option B

Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Last Answer : Answer: Option C

Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Description : Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) The average crushing strength of hand moulded bricks is 6000 t/m2 (B) The average tensile strength of hand moulded brick is 200 t/m2 (C) The average shearing strength of hand moulded brick is 600 t/m2 (D) All the above

Description : Pick up the correct statement from the following: (A) The average crushing strength of hand moulded bricks is 6000 t/m2 (B) The average tensile strength of hand moulded brick is 200 t/m2 (C) The average shearing strength of hand moulded brick is 600 t/m2 (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The plywoods do not split or crack due to changes in atmosphere (B) The commercial plywoods are available upto 150 cm wide and upto 300 cm long (C) The plywoods possess uniform tensile strength in all directions (D) All the above

Description : Pick up the correct statement from the following: (A) The plywoods do not split or crack due to changes in atmosphere (B) The commercial plywoods are available upto 150 cm wide and upto 300 cm long (C) The plywoods possess uniform tensile strength in all directions (D) All the above

Last Answer : Answer: Option D

Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Description : Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Last Answer : Answer: Option B

The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Description : The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Last Answer : Answer: Option D

The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm2

Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm

Last Answer : Answer: Option C

For testing compressive and tensile strength of cement, the cement mortar is made by mixing cement and standard sand in the proportions of (A) 1 : 2 (B) 1 : 3 (C) 1 : 4 (D) 1 : 6

Description : For testing compressive and tensile strength of cement, the cement mortar is made by mixing cement and standard sand in the proportions of (A) 1 : 2 (B) 1 : 3 (C) 1 : 4 (D) 1 : 6

Last Answer : Answer: Option B

Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Description : Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Last Answer : (a) 10 to 15%

The tensile strength of concrete is given by [ A ] 0.45 vfCK [ B ] 0.60 vfCK [ C ] 0.70 vfCK [ D ] 0.90 vfCK

Description : The tensile strength of concrete is given by [ A ] 0.45 vfCK [ B ] 0.60 vfCK [ C ] 0.70 vfCK [ D ] 0.90 vfCK

Last Answer : [ C ] 0.70 vfCK

The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Description : The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Last Answer : [ A ] 10% to 15%

Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Description : Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Last Answer : [ A ] Consistency