CMOS circuits are extensively used for ON-chip computers mainly because of their extremely (A) low power dissipation. (B) high noise immunity. (C) large packing density. (D) low cost.

CMOS circuits are extensively used for ON-chip computers mainly because of their extremely
(A) low power dissipation. (B) high noise immunity.
(C) large packing density. (D) low cost.
by

1 Answer

Answer :

Ans: C
 Because CMOS circuits have large packing density.
by

Related questions

The digital logic family which has minimum power dissipation is (A) TTL (B) RTL (C) DTL (D) CMOS

Description : The digital logic family which has minimum power dissipation is (A) TTL (B) RTL (C) DTL (D) CMOS

Last Answer : (D) CMOS The digital logic family which has minimum power dissipation is CMOS. (CMOS being an unipolar logic family, occupy a very small fraction of silicon Chip area)

CMOS circuits consume power (A) Equal to TTL (B) Less than TTL (C) Twice of TTL (D) Thrice of TTL

Description : CMOS circuits consume power (A) Equal to TTL (B) Less than TTL (C) Twice of TTL (D) Thrice of TTL

Last Answer : Ans: B As in CMOS one device is ON & one is Always OFF so power consumption is low.

The MSI chip 7474 is (A) Dual edge triggered JK flip-flop (TTL). (B) Dual edge triggered D flip-flop (CMOS). (C) Dual edge triggered D flip-flop (TTL). (D) Dual edge triggered JK flip-flop (CMOS).

Description : The MSI chip 7474 is (A) Dual edge triggered JK flip-flop (TTL). (B) Dual edge triggered D flip-flop (CMOS). (C) Dual edge triggered D flip-flop (TTL). (D) Dual edge triggered JK flip-flop (CMOS).

Last Answer : Ans: C MSI chip 7474 dual edge triggered D Flip-Flop.

In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Description : In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Last Answer : Ans: A Lower propagation delay as shottky transistors reduce the storage time delay by preventing the transistor from going deep into saturation.

Which of following consume minimum power (A) TTL. (B) CMOS. (C) DTL. (D) RTL.

Description : Which of following consume minimum power (A) TTL. (B) CMOS. (C) DTL. (D) RTL.

Last Answer : Ans: B CMOS consumes minimum power as in CMOS one p-MOS & one n-MOS transistors are connected in complimentary mode, such that one device is ON & one is OFF.

The logic 0 level of a CMOS logic device is approximately (A) 1.2 volts (B) 0.4 volts (C) 5 volts (D) 0 volts

Description : The logic 0 level of a CMOS logic device is approximately (A) 1.2 volts (B) 0.4 volts (C) 5 volts (D) 0 volts

Last Answer : Ans: D CMOS logic low level is 0 volts approx.

Which of the following is the fastest logic? (A) ECL (B) TTL (C) CMOS (D) LSI

Description : Which of the following is the fastest logic? (A) ECL (B) TTL (C) CMOS (D) LSI

Last Answer : (A) ECL

The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Description : The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Last Answer : Ans: A The digital logic family which has the lowest propagation delay time is ECL (Lowest propagation delay time is possible in ECL because the transistors are used in difference amplifier configuration, in which they are never driven into saturation and thereby the storage time is eliminated).

Which of the following is the fastest logic (A) TTL (B) ECL (C) CMOS (D) LSI

Description : Which of the following is the fastest logic (A) TTL (B) ECL (C) CMOS (D) LSI

Last Answer : Ans: B ECL is the fastest logic family of all logic families. (High speeds are possible in ECL because the transistors are used in difference amplifier configuration, in which they are never driven into saturation and thereby the storage time is eliminated.

In a CMOS inverter, the dynamic power dissipation

Description : In a CMOS inverter, the dynamic power dissipation  (A) decreases with power supply voltage  (B) increases with power supply voltage  (C) is independent of power supply voltage  (D) is zero

Last Answer : In a CMOS inverter, the dynamic power dissipation  increases with power supply voltage 

What are the classification of sequential circuits?

Description : What are the classification of sequential circuits?

Last Answer : The sequential circuits are classified on the basis of timing of their signals into two types. They are, 1)Synchronous sequential circuit. 2)Asynchronous sequential circuit.

Karnaugh map is used for the purpose of (A) Reducing the electronic circuits used. (B) To map the given Boolean logic function. (C) To minimize the terms in a Boolean expression. (D) To maximize the terms of a given a Boolean expression.

Description : Karnaugh map is used for the purpose of (A) Reducing the electronic circuits used. (B) To map the given Boolean logic function. (C) To minimize the terms in a Boolean expression. (D) To maximize the terms of a given a Boolean expression.

Last Answer : (C) To minimize the terms in a Boolean expression.

Data can be changed from special code to temporal code by using (A) Shift registers (B) counters (C) Combinational circuits (D) A/D converters.

Description : Data can be changed from special code to temporal code by using (A) Shift registers (B) counters (C) Combinational circuits (D) A/D converters.

Last Answer : Ans: A Data can be changed from special code to temporal code by using Shift Registers. (A Register in which data gets shifted towards left or right when clock pulses are applied is known as a Shift Register.)

Which numbering format is most commonly used in a computer's machine language? 23) A) ASCII B) hexadecimal C) octal D) BCD

Description : Which numbering format is most commonly used in a computer's machine language? 23) A) ASCII B) hexadecimal C) octal D) BCD

Last Answer : B) hexadecimal

The chief reason why digital computers use complemented subtraction is that it (A) Simplifies the circuitry. (B) Is a very simple process. (C) Can handle negative numbers easily. (D) Avoids direct subtraction.

Description : The chief reason why digital computers use complemented subtraction is that it (A) Simplifies the circuitry. (B) Is a very simple process. (C) Can handle negative numbers easily. (D) Avoids direct subtraction.

Last Answer : Ans: C Using complement method negative numbers can also be subtracted.

Does anyone have experience cleaning the CMOS-chip of his camera?

Description : Does anyone have experience cleaning the CMOS-chip of his camera?

Last Answer : Vacuum cleaner ONLY.

Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Description : Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Last Answer : i) Noise immunity is measured in terms of noise margin. High state Noise margin = VNH = VOH(min) - VIH(min) Low state Noise margin = VNL = VIL(max) - VOL(max) i) The fan-out is defined as the ... logical 0 state (HIGH to LOW) iii) Average power dissipation is defined as PD(avg) = ICC(avg) * VCC

The NOR gate output will be low if the two inputs are (A) 00 (B) 01 (C) 10 (D) 11

Description : The NOR gate output will be low if the two inputs are (A) 00 (B) 01 (C) 10 (D) 11

Last Answer : A

The NAND gate output will be low if the two inputs are (A) 00 (B) 01 (C) 10 (D) 11

Description : The NAND gate output will be low if the two inputs are (A) 00 (B) 01 (C) 10 (D) 11

Last Answer : (D) 11

What is the advantage of PTM over PAM? A. All of these B. Low sampling rate is required C. Much better noise immunity D. Simpler to generate

Description : What is the advantage of PTM over PAM? A. All of these B. Low sampling rate is required C. Much better noise immunity D. Simpler to generate

Last Answer : C. Much better noise immunity

The lustre of the metals is because of (1) high density, due to closed packing of atoms (2) high polish (3) reflection of light due to the presence of free electrons (4) absorption of light due to the presence of cavities

Description : The lustre of the metals is because of (1) high density, due to closed packing of atoms (2) high polish (3) reflection of light due to the presence of free electrons (4) absorption of light due to the presence of cavities

Last Answer : reflection of light due to the presence of free electrons

Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Description : Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Last Answer : (B) Flexibility possible in the baffle arrangement

For JK flipflop J = 0, K=1, the output after clock pulse will be (A) 1. (B) no change. (C) 0. (D) high impedance.

Description : For JK flipflop J = 0, K=1, the output after clock pulse will be (A) 1. (B) no change. (C) 0. (D) high impedance.

Last Answer : Ans: C J=0, K=1, these inputs will reset the flip-flop after the clock pulse. So whatever be the previous output, the next state will be 0.

The output of SR flip flop when S=1, R=0 is (A) 1 (B) 0 (C) No change (D) High impedance

Description : The output of SR flip flop when S=1, R=0 is (A) 1 (B) 0 (C) No change (D) High impedance

Last Answer : Ans: A As for the SR flip-flop S=set input R=reset input ,when S=1, R=0, Flip-flop will be set.

For JK flip flop with J=1, K=0, the output after clock pulse will be (A) 0. (B) 1. (C) high impedance. (D) no change.

Description : For JK flip flop with J=1, K=0, the output after clock pulse will be (A) 0. (B) 1. (C) high impedance. (D) no change.

Last Answer : (B) 1.

Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments (B) Pressure drop in the equipment will be very high (C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Description : Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the ... C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Last Answer : (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments

An Arithmetic Logic Unit (ALU) normally contains a number of multiplexer circuits. How many of these might you expect to find in an ALU in a modern CPU chip, and what is their purpose?

Description : An Arithmetic Logic Unit (ALU) normally contains a number of multiplexer circuits. How many of these might you expect to find in an ALU in a modern CPU chip, and what is their purpose?

Last Answer : answer:FYI, We don’t do homework here. Hint: Realize that an ALU needs to be fed instructions (opcodes) and that they will need to be decoded. This question is also somewhat dated.

The code where all successive numbers differ from their preceding number by single bit is (A) Binary code. (B) BCD. (C) Excess – 3. (D) Gray.

Description : The code where all successive numbers differ from their preceding number by single bit is (A) Binary code. (B) BCD. (C) Excess – 3. (D) Gray.

Last Answer : Ans: D The code where all successive numbers differ from their preceding number by single bit is Gray Code. (It is an unweighted code. The most important characteristic of this code is that only a single bit change occurs when going from one code number to next.)

Water is normally used as a coolant in the heat exchange equipments mainly because of its (A) Abundance & high heat capacity (B) Low density (C) Low viscosity (D) High fluidity

Description : Water is normally used as a coolant in the heat exchange equipments mainly because of its (A) Abundance & high heat capacity (B) Low density (C) Low viscosity (D) High fluidity

Last Answer : (A) Abundance & high heat capacity

When the conduction current density and displacement current density are same, the dissipation factor will be a) Zero b) Minimum c) Maximum d) Unity

Description : When the conduction current density and displacement current density are same, the dissipation factor will be a) Zero b) Minimum c) Maximum d) Unity

Last Answer : d) Unity

Which system was used extensively by early mini computers. a. Decimal number b. Octal number c. Hexadecimal number d. Binary number

Description : Which system was used extensively by early mini computers. a. Decimal number b. Octal number c. Hexadecimal number d. Binary number

Last Answer : b. Octal number

Virtual memory is _________ A. an extremely large main memory B. an extremely large secondary memory C. a type of used in super computers D. an illusion of extremely large main memory

Description : Virtual memory is _________ A. an extremely large main memory B. an extremely large secondary memory C. a type of used in super computers D. an illusion of extremely large main memory

Last Answer : D. an illusion of extremely large main memory

Virtual memory is (A) an extremely large main memory. (B) an extremely large secondary memory. (C) an illusion of extremely large main memory (D) a type of memory used in super computers.

Description : Virtual memory is (A) an extremely large main memory. (B) an extremely large secondary memory. (C) an illusion of extremely large main memory (D) a type of memory used in super computers.

Last Answer : (C) an illusion of extremely large main memory

An ideal tower packing should not (A) Have low weight per unit volume (B) Have large surface area per unit volume (C) Have large free cross-section (D) Hold up large amount of liquid in the packing

Description : An ideal tower packing should not (A) Have low weight per unit volume (B) Have large surface area per unit volume (C) Have large free cross-section (D) Hold up large amount of liquid in the packing

Last Answer : (D) Hold up large amount of liquid in the packing

Which of the following is an undesirable property in a tower packing? (A) Large surface per unit volume (B) Large free cross-section (C) Low weight per unit volume (D) Large weight of liquid retained

Description : Which of the following is an undesirable property in a tower packing? (A) Large surface per unit volume (B) Large free cross-section (C) Low weight per unit volume (D) Large weight of liquid retained

Last Answer : (D) Large weight of liquid retained

What is it called when millions of circuits are connected to a silicon chip ?

Description : What is it called when millions of circuits are connected to a silicon chip ?

Last Answer : When millions of circuits are connected to a silicon chip, it is called IC or IC (Integrated Circuit) .

Define Asynchronous sequential circuit?

Description : Define Asynchronous sequential circuit?

Last Answer : In asynchronous sequential circuits change in input signals can affect memory element at any instant of time.

Define synchronous sequential circuit

Description : Define synchronous sequential circuit

Last Answer : In synchronous sequential circuits, signals can affect the memory elements only at discrete instant of time.

What are the different types of shift type?

Description : What are the different types of shift type?

Last Answer : There are five types. They are, Serial In Serial Out Shift Register Serial In Parallel Out Shift Register Parallel In Serial Out Shift Register Parallel In Parallel Out Shift Register Bidirectional Shift Register

Define shift registers.

Description : Define shift registers.

Last Answer : The binary information in a register can be moved from stage to stage within the register or into or out of the register upon application of clock ... arithmetic and logic operations used in microprocessors. This gives rise to group of registers called shift registers.

Define registers.

Description : Define registers.

Last Answer : A register is a group of flip-flops flip-flop can store one bit information. So an n-bit register has a group of n flip-flops and is capable of storing any binary information/number containing n-bits.

What is a master-slave flip-flop?

Description : What is a master-slave flip-flop?

Last Answer : A master-slave flip-flop consists of two flip-flops where one circuit serves as a master and the other as a slave.

What is edge-triggered flip-flop?

Description : What is edge-triggered flip-flop?

Last Answer : The problem of race around condition can solved by edge triggering flip flop. The term edge triggering means that the flip-flop changes state either at the positive ... negative edge of the clock pulse and it is sensitive to its inputs only at this transition of the clock.

Define race around condition.

Description : Define race around condition.

Last Answer : In JK flip-flop output is fed back to the input. Therefore change in the output results change in the input. Due to this in the positive half of the clock pulse if both J and K are high then output toggles continuously. This condition iscalled ‘race around condition’.

What is the operation of T flip-flop?

Description : What is the operation of T flip-flop?

Last Answer : T flip-flop is also known as Toggle flip-flop. • When T=0 there is no change in the output. • When T=1 the output switch to the complement state (ie) the output toggles.

What is the operation of JK flip-flop?

Description : What is the operation of JK flip-flop?

Last Answer : When K input is low and J input is high the Q output of flip-flop is set. When K input is high and J input is low the Q output of flip-flop is reset. When both the inputs ... are high it is possible to set or reset the flip-flop (ie) the output toggle on the next positive clock edge.

What is the operation of D flip-flop?

Description : What is the operation of D flip-flop?

Last Answer : In D flip-flop during the occurrence of clock pulse if D=1, the output Q is set and if D=0, the output is reset.

What are the different types of flip-flop?

Description : What are the different types of flip-flop?

Last Answer : There are various types of flip flops. Some of them are mentioned below they are, RS flip-flop SR flip-flop D flip-flop JK flip-flop T flip-flop

Define Flip flop.

Description : Define Flip flop.

Last Answer : The basic unit for storage is flip flop. A flip-flop maintains its output state either at 1 or 0 until directed by an input signal to change its state.