The method of plane tabling commonly used for establishing the instrument station is a method of (a) Radiation (b) Intersection* (c) Resection (d) Traversing

The method of plane tabling commonly used for establishing the instrument station is a
method of
(a) Radiation
(b) Intersection*
(c) Resection
(d) Traversing
by

1 Answer

Answer :

(b) Intersection*
by

Related questions

Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Description : Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Last Answer : (D) Resection

For locating an inaccessible point with the help of only a plane table, one should use (a) traversing (b) resection (c) radiation (e) Intersection*

Description : For locating an inaccessible point with the help of only a plane table, one should use (a) traversing (b) resection (c) radiation (e) Intersection*

Last Answer : (e) Intersection*

The process of determining the locations of the instrument station by drawing re sectors from the locations of the known stations is (A) Radiation (B) Intersection (C) Resection (D) Traversing

Description : The process of determining the locations of the instrument station by drawing re sectors from the locations of the known stations is (A) Radiation (B) Intersection (C) Resection (D) Traversing

Last Answer : (C) Resection

In a plane-table survey, the process of determining the plotted position of a station occupied by the plane-table by means of sights taken towards known points, the locations of which have already been plotted, is known as (a) Radiation (b) Resection (c) Intersection (d) Traversing

Description : In a plane-table survey, the process of determining the plotted position of a station occupied by the plane-table by means of sights taken towards known points, the locations of which have already been plotted, is known as (a) Radiation (b) Resection (c) Intersection (d) Traversing

Last Answer : (b) Resection

The methods used for locating the plane table stations are (i) Radiation (ii) Traversing (iii) Intersection (iv) Resection The correct answer is (A) (i) and (ii) (B) (iii) and (iv) (C) (ii) and (iv) (D) (i) and (iii)

Description : The methods used for locating the plane table stations are (i) Radiation (ii) Traversing (iii) Intersection (iv) Resection The correct answer is (A) (i) and (ii) (B) (iii) and (iv) (C) (ii) and (iv) (D) (i) and (iii)

Last Answer : (C) (ii) and (iv)

Which of the following methods of plane table surveying is used to locate the position of an inaccessible point? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Description : Which of the following methods of plane table surveying is used to locate the position of an inaccessible point? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Last Answer : (B) Intersection

Locating the position of a plane table station with reference to three known points, is known as (A) Intersection method (B) Radiation method (C) Resection method (D) Three point problem

Description : Locating the position of a plane table station with reference to three known points, is known as (A) Intersection method (B) Radiation method (C) Resection method (D) Three point problem

Last Answer : (D) Three point problem

Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Description : Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Last Answer : Advantages of intersection method: 1. Interection method requires less ground distance measurement than radiation method. 2. By this method we can locate inaccessible points which cannot be ... to radiation method, intersection method eliminates undulation error, bisection error and plotting errors.

The plotting of inaccessible points in a plane-table survey can be done by the method of (a) Interpolation (b) Radiation (c) Intersection (d) Traversing

Description : The plotting of inaccessible points in a plane-table survey can be done by the method of (a) Interpolation (b) Radiation (c) Intersection (d) Traversing

Last Answer : (c) Intersection

To orient a plane table at a point with two inaccessible points, the method generally adopted, is (A) Intersection (B) Resection (C) Radiation (D) Two point problem

Description : To orient a plane table at a point with two inaccessible points, the method generally adopted, is (A) Intersection (B) Resection (C) Radiation (D) Two point problem

Last Answer : (D) Two point problem

Detailed plotting is generally done by (A) Radiation (B) Traversing (C) Resection (D) All of the above

Description : Detailed plotting is generally done by (A) Radiation (B) Traversing (C) Resection (D) All of the above

Last Answer : (A) Radiation

One of the Lehmann's rules of plane tabling, is (A) Location of the instrument station is always distant from each of the three rays from the known points in proportion to their distances (B) When looking in the direction of each of the given points, the instrument station will be on the right side of one and left side of the other ray (C) When the instrument station is outside the circumscribing circle its location is always on the opposite side of the ray to the most distant point as the inter-section of the other two rays (D) None of these

Description : One of the Lehmann's rules of plane tabling, is  (A) Location of the instrument station is always distant from each of the three rays from the  known points in proportion to their distances  ( ... to the most distant point as the inter-section of the other two rays  (D) None of these 

Last Answer : (A) Location of the instrument station is always distant from each of the three rays from the  known points in proportion to their distances 

Explain with neat sketch the procedure of radiation method of plane tabling.

Description : Explain with neat sketch the procedure of radiation method of plane tabling.

Last Answer : 1. The table is set at suitable station e.g. P from where all stations can be sighted and measured. 2. After centering and leveling, mark station P as P' on sheet. 3. Suppose stations A, B, C, and D are ... marked as pa. 5. Similarly station B, C and D are bisected and marked as b, c and d.

While working on a plane table, the correct rule is: (A) Draw continuous lines from all instrument stations (B) Draw short rays sufficient to contain the points sought (C) Intersection should be obtained by actually drawing second rays (D) Take maximum number of sights as possible from each station to distant objects

Description : While working on a plane table, the correct rule is: (A) Draw continuous lines from all instrument stations (B) Draw short rays sufficient to contain the points sought (C) Intersection ... drawing second rays (D) Take maximum number of sights as possible from each station to distant objects

Last Answer : (B) Draw short rays sufficient to contain the points sought

The two point problem and three point problem are methods of (A) Resection (B) Orientation (C) Traversing (D) Resection and orientation

Description : The two point problem and three point problem are methods of (A) Resection (B) Orientation (C) Traversing (D) Resection and orientation

Last Answer : (D) Resection and orientation

The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Description : The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Last Answer : (B) Telescopic alidade

For benefication of iron ore, the most commonly used method is (A) Flocculation (B) Froth floatation (C) Jigging & tabling (D) None of these

Description : For benefication of iron ore, the most commonly used method is (A) Flocculation (B) Froth floatation (C) Jigging & tabling (D) None of these

Last Answer : (C) Jigging & tabling

In setting up a plane table at any station (a) Leveling is done first (b) Centering is done first (c) Both leveling and centering are done simultaneously * (d) Orientation is done first

Description : In setting up a plane table at any station (a) Leveling is done first (b) Centering is done first (c) Both leveling and centering are done simultaneously * (d) Orientation is done first

Last Answer : c) Both leveling and centering are done simultaneously *

Draw sketch and explain method of traversing of plane table surveying.

Description : Draw sketch and explain method of traversing of plane table surveying. 

Last Answer : Procedure: 1.Set plane table over station A use plumbing fork for transferring station point from ground on sheet. Draw the direction of magnetic meridian with the help of compass. 2. With the ... scale Similarly, the table can be set at other successive station and traverse is completed.

Describe in brief resection method of plane table surveying.

Description : Describe in brief resection method of plane table surveying.

Last Answer : This method is used for establishing the instrument stations only. After fixing the stations, details are located either by radiation or intersection. The characteristic feature of resection is that the point ... of resection are (1)The Two Point Problem, and (2)Three Point Problem.

Compare radiation and intersection methods of plane table surveying on any two parameters.

Description : Compare radiation and intersection methods of plane table surveying on any two parameters. 

Last Answer : Radiation method Intersection method 1. It requires the plane table to occupy a single station.  1. This method requires setting the table up at minimum of two stations.  ... for locating inaccessible points by the intersection of the rays drawn from two instruments stations. 

In order to do fly levelling the following type of methodology is adopted (a) Rise & fall method (b) Height of instrument method (c) Both the above* (d) None of the above

Description : In order to do fly levelling the following type of methodology is adopted (a) Rise & fall method (b) Height of instrument method (c) Both the above* (d) None of the above

Last Answer : c) Both the above*

Conventional method of camber recording a) Piano wire with counter weight* b) By using leveling instrument c) Offset method d) None of the above

Description : Conventional method of camber recording a) Piano wire with counter weight* b) By using leveling instrument c) Offset method d) None of the above

Last Answer : a) Piano wire with counter weight*

Which of the following methods of theodolite traversing is suitable for locating the details which are far away from transit stations? (A) Measuring angle and distance from one transit station (B) Measuring angles to the point from at least two stations (C) Measuring angle at one station and distance from other (D) Measuring distance from two points on traverse line

Description : Which of the following methods of theodolite traversing is suitable for locating the details which are far away from transit stations? (A) Measuring angle and distance from one transit station (B) ... at one station and distance from other (D) Measuring distance from two points on traverse line

Last Answer : (B) Measuring angles to the point from at least two stations

State the procedure of traversing by using total station.

Description : State the procedure of traversing by using total station.

Last Answer : The procedure is as follows. A) CENTERING THE TOTAL STATION: The instrument must be vertically above the survey station to ensure that horizontal angle observations are correct. The steps are as ... are plumbed over peg 1 and 3. Horizontal distances and angles are measured and recorded similarly.

While surveying a plot of land by plane tabling, the field observations (A) And plotting proceed simultaneously (B) And plotting do not proceed simultaneously (C) And recorded in field books to be plotted later (D) All the above

Description : While surveying a plot of land by plane tabling, the field observations (A) And plotting proceed simultaneously (B) And plotting do not proceed simultaneously (C) And recorded in field books to be plotted later (D) All the above

Last Answer : (A) And plotting proceed simultaneously

Explain errors occurred due to manipulation and sighting in plane tabling.

Description : Explain errors occurred due to manipulation and sighting in plane tabling.

Last Answer : i) The board not being horizontal- This error affects chiefly the measurement of vertical angles. ii) The table not being accurately centered. The plotted position of the occupied station not ... and correct any displacement. v) The defective sighting- The object not being correctly sighted.

Define orientation and principle of plane tabling.

Description : Define orientation and principle of plane tabling. 

Last Answer : Orientation: The orientation of plane table means keeping the plane table at all stations parallel to the position it occupied at first station. Principles of plane table survey: 1. The rays drawn from ... same as that of previous station i.e. orientation should be done at each changed station.  

Enlist the methods of plane tabling.

Description : Enlist the methods of plane tabling. 

Last Answer : Method of Surveying with the plane table are : 1) Radiation 2) Intersection 3) Traversing 4) Resection

What are the sources of errors in plane tabling?

Description : What are the sources of errors in plane tabling?

Last Answer : The following are the sources of errors in plane tabling 1) The board not being horizontal 2) The table not being accurately centered 3) The table not being Correctly oriented 4) The objects ... through the station point 7) Inaccuracy in plotting 8) The expansion and contraction of the paper 

Explain ‘Intersection Method’ of plane table surveying with neat sketch. Also give situation when intersection method is used.

Description : Explain ‘Intersection Method’ of plane table surveying with neat sketch. Also give situation when intersection method is used.

Last Answer : 1. Lay out a base line AB and measure it and Plot a distance ab' on sheet using any scale. 2.Set up instrument at A' with a' over A' 3.Orient the table by placing alidade ... the case of the survey of mountainous country. 5. The only linear measurement required is that of a base line.

Explain intersection method of plane survey.

Description : Explain intersection method of plane survey.

Last Answer : Intersection method of plane tabling 1. Lay out a base line AB and measure it and Plot a distance ab' on sheet using any scale. 2.Set up instrument at A' with a' over A' 3.Orient the table by ... sighted rays bd, bg, bf, bc are drawn to determine points intersection, d, g, f, c.

The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error such that each ray is equally rotated either clockwise or anti clockwise 5. The points obtained by three rays are the correct location. The correct sequence is (A) 1, 3, 2, 4, 5 (B) 1, 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Description : The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error ... 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Last Answer : (A) 1, 3, 2, 4, 5

The commonly used power transmission system in ferti seed drills are: a) China-sprocket and gears b) Gears and belt pulleys c) Belt pulleys and cams d) Belt pulleys and chain sprocket

Description : The commonly used power transmission system in ferti seed drills are: a) China-sprocket and gears b) Gears and belt pulleys c) Belt pulleys and cams d) Belt pulleys and chain sprocket

Last Answer : d) Belt pulleys and chain sprocket

The commonly used lime in white washing is a) Hydraulic lime b) Slaked lime c) Plain lime d) White lime*

Description : The commonly used lime in white washing is a) Hydraulic lime b) Slaked lime c) Plain lime d) White lime*

Last Answer : d) White lime*

The survey instrument used for reconnaissance survey (a) Theodelite & Dumpty level (b) Prismatic compass & Aneriod barometer* (c) All the above (d) None of them

Description : The survey instrument used for reconnaissance survey (a) Theodelite & Dumpty level (b) Prismatic compass & Aneriod barometer* (c) All the above (d) None of them

Last Answer : (b) Prismatic compass & Aneriod barometer*

Which of the following in theodolite work is imperfect adjustment of the instrument (a) Error due to line of collimation being perpendicular to the horizontal axis (b) Error due to axis not to perpendicular of the vertical axis (c) Error due to imperfect graduation (d) Error due to eccentricity of vernires (e) All of the above*

Description : Which of the following in theodolite work is imperfect adjustment of the instrument (a) Error due to line of collimation being perpendicular to the horizontal axis (b) Error due to axis not to perpendicular ... to imperfect graduation (d) Error due to eccentricity of vernires (e) All of the above*

Last Answer : (e) All of the above*

Theodolite is an instrument used for (a) Tightening the capstan-headed nuts of level tube (b) Measurement of horizontal angles only (c) Measurement of vertical angles only (d) Measurement of both horizontal and vertical angles*

Description : Theodolite is an instrument used for (a) Tightening the capstan-headed nuts of level tube (b) Measurement of horizontal angles only (c) Measurement of vertical angles only (d) Measurement of both horizontal and vertical angles*

Last Answer : (d) Measurement of both horizontal and vertical angles*

Dumpy level is most suitable when (a) The instrument is to be shifted frequently (b) Fly leveling is being done over long distance (c) Many readings are to be taken from a single setting of the instrument* (d) All of the above

Description : Dumpy level is most suitable when (a) The instrument is to be shifted frequently (b) Fly leveling is being done over long distance (c) Many readings are to be taken from a single setting of the instrument* (d) All of the above

Last Answer : (c) Many readings are to be taken from a single setting of the instrument*

The following instrument is used to set out a right angle (a) Cross staff (b) Optical staff (c) Prism square (d) None of the above (e) All the above*

Description : The following instrument is used to set out a right angle (a) Cross staff (b) Optical staff (c) Prism square (d) None of the above (e) All the above*

Last Answer : e) All the above*

As per norms for desirable amenity as given to model station, the retiring rooms should be provided on stations classified as --- (a) A & B* (b) A,B & C (c) A,B,C & D (d) A, B,C, D & E (e) A

Description : As per norms for desirable amenity as given to model station, the retiring rooms should be provided on stations classified as --- (a) A & B* (b) A,B & C (c) A,B,C & D (d) A, B,C, D & E (e) A

Last Answer : a) A & B*

As per norms for desirable amenity as given to model station, the clock rooms should be provided on stations classified as --- (a) A & B * (b) A,B & C (c) A,B,C & D (d) A, B,C, D & E (e) A

Description : As per norms for desirable amenity as given to model station, the clock rooms should be provided on stations classified as --- (a) A & B * (b) A,B & C (c) A,B,C & D (d) A, B,C, D & E (e) A

Last Answer : (a) A & B *

As per norms for desirable amenity as given to model station, the water coolers should be provided on stations classified as --- (a) A & B (b) A,B & C (c) A,B,C & D* (d) A, B,C, D & E (e) A

Description : As per norms for desirable amenity as given to model station, the water coolers should be provided on stations classified as --- (a) A & B (b) A,B & C (c) A,B,C & D* (d) A, B,C, D & E (e) A

Last Answer : (c) A,B,C & D*

As per norms for desirable amenity as given to model station, the parking facility/circulating area should be provided on stations classified as --- (a) A & B (b) A,B & C (c) A,B,C & D* (d) A, B,C, D & E

Description : As per norms for desirable amenity as given to model station, the parking facility/circulating area should be provided on stations classified as --- (a) A & B (b) A,B & C (c) A,B,C & D* (d) A, B,C, D & E

Last Answer : (c) A,B,C & D*

As per norms for desirable amenity as given to model station, the public address system should be provided on stations classified as --- (a) A & B (b) A,B & C* (c) A,B,C & D (d) A, B,C, D & E (e) A

Description : As per norms for desirable amenity as given to model station, the public address system should be provided on stations classified as --- (a) A & B (b) A,B & C* (c) A,B,C & D (d) A, B,C, D & E (e) A

Last Answer : (b) A,B & C*

As per norms for desirable amenity as given to model station, the book stalls should be provided on stations classified as --- (a) A & B (b) A,B & C* (c) A,B,C & D (d) A, B,C, D & E (e) A

Description : As per norms for desirable amenity as given to model station, the book stalls should be provided on stations classified as --- (a) A & B (b) A,B & C* (c) A,B,C & D (d) A, B,C, D & E (e) A

Last Answer : (b) A,B & C*

As per norms for desirable amenity as given to model station, the refreshment rooms should be provided on stations classified as --- (a) A & B* (b) A,B & C (c) A,B,C & D (d) A, B,C, D & E (e) A

Description : As per norms for desirable amenity as given to model station, the refreshment rooms should be provided on stations classified as --- (a) A & B* (b) A,B & C (c) A,B,C & D (d) A, B,C, D & E (e) A

Last Answer : (a) A & B*

“B” class station is provided only on (a) Single lines (b) Double line (c) On both single as well as double line* (d) None of them

Description : “B” class station is provided only on (a) Single lines (b) Double line (c) On both single as well as double line* (d) None of them

Last Answer : c) On both single as well as double line*

Height of platform of a flag station in cutting above rail level is (a) Same height as Rail level (b) 305 mm above rail level (c) 455 mm above rail level (d) 840mm above rail level*

Description : Height of platform of a flag station in cutting above rail level is (a) Same height as Rail level (b) 305 mm above rail level (c) 455 mm above rail level (d) 840mm above rail level*

Last Answer : (d) 840mm above rail level*

Which of the facilities do not exist at halt station? (a) Facilities for stopping the train (b) Facilities for a small waiting (c) Facilities for crossing of train* (d) Facilities for book of passengers

Description : Which of the facilities do not exist at halt station? (a) Facilities for stopping the train (b) Facilities for a small waiting (c) Facilities for crossing of train* (d) Facilities for book of passengers

Last Answer : (c) Facilities for crossing of train*