In PVC insulated cables, PVC stands for___________.

In PVC insulated cables, PVC stands for___________. A. Ploy Voltage Capacitor B. Poly Vinyl Capacitor C. Primary Voltage Capacitor D. Polyvinyl chloride
by

1 Answer

Answer :

In PVC insulated cables, PVC stands for Polyvinyl chloride.

by

Related questions

What are the advantages of PVC insulated cable?

Description : What are the advantages of PVC insulated cable? 

Last Answer : a. Plumbing is not required. Joints can be made easily. b. As PVC is light the injury caused to it while laying is less. c. It is corrosion resistant. d. It has high fire retarding property. e. It does not break down even if moisture enters. 

Cables for 220 kV lines are invariably (a) mica insulated (b) paper insulated (c) compressed oil or compressed gas insulated (d) rubber insulated (e) none of the above

Description : Cables for 220 kV lines are invariably (a) mica insulated (b) paper insulated (c) compressed oil or compressed gas insulated (d) rubber insulated (e) none of the above

Last Answer : (c) compressed oil or compressed gas insulated

In the cables, the location of fault is usually found out by comparing (a) the resistance of the conductor (b) the inductance of conductors (c) the capacitances of insulated conductors (d) all above parameters

Description : In the cables, the location of fault is usually found out by comparing (a) the resistance of the conductor (b) the inductance of conductors (c) the capacitances of insulated conductors (d) all above parameters

Last Answer : (c) the capacitances of insulated conductors

For LV applications (below 1 kV), ______________ cables are used. (A) Paper insulated. (B) Plastic. (C) Single core cables. (D) Oil filled.

Description : For LV applications (below 1 kV), ______________ cables are used. (A) Paper insulated. (B) Plastic. (C) Single core cables. (D) Oil filled.

Last Answer : Ans: C For low voltage applications single core cables are suitable.

What material is most often used for the outer covering of coaxial cables? A. PVC B. Teflon C. PE D. Polystyrene

Description : What material is most often used for the outer covering of coaxial cables? A. PVC B. Teflon C. PE D. Polystyrene

Last Answer : A. PVC

Why fuses with fusing factor more than 1.5 is not allowed in PVC cables?

Description : Why fuses with fusing factor more than 1.5 is not allowed in PVC cables? 

Last Answer : Because PVC cables have low thermal capacity than paper cables. Full loading of PVC only possible if it has close excess current protection (i.e.) Fusing Factor = 1.5 

Conduit pipes are normally used to protect _____ cables. (a) unsheathed cables (b) armoured (c) PVC sheathed cables (d) all of the above

Description : Conduit pipes are normally used to protect _____ cables. (a) unsheathed cables (b) armoured (c) PVC sheathed cables (d) all of the above

Last Answer : (a) unsheathed cables

In M.I. cables, M.I. stands for ______________-.

Description : In M.I. cables, M.I. stands for ______________-. A. Modulation Index B. Multiple Insulation C. Metal Insulation D. Mineral Insulation 

Last Answer : In M.I. cables, M.I. stands for Mineral Insulation.

The term PVC used in the plastic industry stands for

Description : The term PVC used in the plastic industry stands for

Last Answer : polyvinyl chloride

The term PVC used in the plastic industry stands for - (1) polyvinyl chloride (2) polyvinyl carbonate (3) phosphor vanadium chloride (4) phosphavinyl chloride

Description : The term PVC used in the plastic industry stands for - (1) polyvinyl chloride (2) polyvinyl carbonate (3) phosphor vanadium chloride (4) phosphavinyl chloride

Last Answer : (1) polyvinyl chloride Explanation: Polyvinyl chloride is the world's third-most widely produced synthetic plastic polymer, after polyethylene and polypropylene. About 40 million tones are produced per year.

The term PVC used in the plastic industry stands for-------? A. Phosphavinyl chloride B. Phosphor vanadiu chloride C. Polyvinyl chloride (Answer) D. Polyvinyl carbobate

Description : The term PVC used in the plastic industry stands for-------? A. Phosphavinyl chloride B. Phosphor vanadiu chloride C. Polyvinyl chloride (Answer) D. Polyvinyl carbobate

Last Answer : C. Polyvinyl chloride (Answer)

PVC stands for (A) Plastic very compact (B) Polythene vinyl chloride (C) Polythene vinyl carbon (D) Polythene vanadium carbide

Description : PVC stands for (A) Plastic very compact (B) Polythene vinyl chloride (C) Polythene vinyl carbon (D) Polythene vanadium carbide

Last Answer : Answer: Option B

PVC stands for (a) polyvinyl chloride (b) post varnish conductor (c) pressed and varnished cloth (d) positive voltage conductor (e) none of the above

Description : PVC stands for (a) polyvinyl chloride (b) post varnish conductor (c) pressed and varnished cloth (d) positive voltage conductor (e) none of the above

Last Answer : (a) polyvinyl chloride

Why are overhead transmission lines not insulated?

Description : Why are overhead transmission lines not insulated?

Last Answer : Insulators are useful to help separate electrical conductors when they come into physical contact. Overhead Transmission Lines Are Not Insulated: The overhead transmission line is carrying extreme high voltage and ... a whole lot of thick insulation to absorb the heat produced by such high voltage.

State the function of (i) Neutral section, (ii) Section insulator, (iii) Un-insulated overlap, (iv) Insulated overlap.

Description : State the function of (i) Neutral section, (ii) Section insulator, (iii) Un-insulated overlap, (iv) Insulated overlap.

Last Answer : i) Neutral section: Passing of pantograph under insulated overlap will cause short circuit between two phases of the supply system, damaging OHE & pantograph. To avoid this bridging of two ... belong to two elementary sections. Located at feeding posts, sub sectioning posts and booster sections.

Give purpose and location of i) Uninsulated overlap. ii) Insulated overlap. iii) Neutral section. iv) Section insulator.

Description : Give purpose and location of i) Uninsulated overlap. ii) Insulated overlap. iii) Neutral section. iv) Section insulator.

Last Answer : Ans: i) Insulated overlap: To isolate for operation and maintenance of OHE if two lengths of OHE belong to two elementary sections. Located at feeding posts, sub sectioning posts and booster sections.  ... elementary section. Located at cross over from one track to other, from main line to siding.

State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material.

Description : State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material. 

Last Answer :  (i) Application of PVC paper : 1. It is used in slot lining or motor winding insulation purpose 2. For Insulation of Transformer winding (ii) Application of Porcelain : 1. Mainly used for manufacturing ... on withstand temperature : * H' & C' Class of insulation i e. 180° and above 180°C 

Write one application for the give dielectric material. (i) Polyvinyl Carbide(PVC) (ii) Glass (iii) Mica (iv) Cotton and Silk

Description : Write one application for the give dielectric material. (i) Polyvinyl Carbide(PVC) (ii) Glass (iii) Mica (iv) Cotton and Silk

Last Answer : (i) Polyvinyl Carbide(PVC):it is used in insulation of wires and cables in domestic wiring as well as in aircraft and factory wiring (any one)  (ii) Glass: 1) Alkaline glasses are used for ... with wax or varnishes are used in windings of magnet coils and small medium sized mechanics (any one) 

Does anyone know where I can find an insulated coffee mug that is not made for a cup holder?

Description : Does anyone know where I can find an insulated coffee mug that is not made for a cup holder?

Last Answer : Amazon has a few. There are a lot of those tall narrow ones, but I saw a few more “portly” mugs.

How low can the temperature go in an unheated but insulated cabin in order to damage LCD TV, phone, and computer?

Description : How low can the temperature go in an unheated but insulated cabin in order to damage LCD TV, phone, and computer?

Last Answer : answer:Are you the only one closing in on ten thousand Lurve? That is impressive! I think the computer can survive in very low tempts.. Not sure about the rest. I’m an IT girl and I know we have the AC on the severs 24/7.

In twisted pair cable, two insulated wires are twisted around each other which provides protection against noise. Explain. -Technology

Description : In twisted pair cable, two insulated wires are twisted around each other which provides protection against noise. Explain. -Technology

Last Answer : Twisting the cables keep them close together so that, any external magnetic fields must cross both cable at the same time, so the interference created in one cable is cancelled by the almost exact opposite amount of interference in the other.

Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Description : Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Last Answer : 1. Twisted pair cable2. Crosstalk3. Radiowave4. Wired communication channel5. Resource sharing

Can a panel apartment be insulated?

Description : Can panel homes be insulated?

Last Answer : Thermal insulation is usually applied from the outside. If you are thinking of soundproofing, they are usually used with a soundproofing sponge. You can try, but I don’t think it will insulate much.

Should the house be insulated? 45 cm wall thickness

Description : The situation is that the wall thickness is 45 cm (ytong), we can not dismantle the insulated house. Thank you in advance for your help.

Last Answer : I supposedly don't need to insulate it anymore, its thermal insulation is so good, but if you don't have a problem doing it, I think you should do it. The good can be even better and will definitely pay off over the years. 

Two infinitely long, thin, insulated, straight wires lie in the x-y plane along the x- and y- axis respectively. Each wire carries a current I, respec

Description : Two infinitely long, thin, insulated, straight wires lie in the x-y plane along the x- and y- axis respectively. Each wire carries a current I, respec

Last Answer : Two infinitely long, thin, insulated, straight wires lie in the x-y plane along the x- and y- axis respectively. Each ... x C. y = x-1 D. y = -x+1

Where is the statement of all pipes connected to a storage vessel should be insulated for up to a metre in length is a requirement of Building Regulations Part?

Description : Where is the statement of all pipes connected to a storage vessel should be insulated for up to a metre in length is a requirement of Building Regulations Part?

Last Answer : P

Why are electric wires insulated?

Description : Why are electric wires insulated?

Last Answer : to keep the electricity into keep other things out (e.g. water, people, other wires)to prevent short circuits to nearby wiresto prevent electricutionto prevent firesetc.

In order to find the specific heat capacity of an unknown material a 50 g piece is heated to 80 degrees Celsius and fully immersed in a well insulated calorimeter filled with 100 g of water at 10 degr?

Description : In order to find the specific heat capacity of an unknown material a 50 g piece is heated to 80 degrees Celsius and fully immersed in a well insulated calorimeter filled with 100 g of water at 10 degr?

Last Answer : Assuming that the full question, which the questioner failed to post, is given in the Discussion, below.Taking the specific heat capacity of water as 4.2 Joules per gram per degree C, the metal has a specific heat capacity as approx 0.68 Joules/(g °C).

Should copper pipes be insulated?

Description : Should copper pipes be insulated?

Last Answer : Insulating your copper pipes is a great idea. Insulating with foam will insure less heat loss which save energy and probably take a few bucks off your electricity bill.

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Last Answer : Answer: A

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the machine secured B. millivolt meter and a jumper with the machine running C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the ... C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Last Answer : Answer: B

One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Description : One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Last Answer : Answer: D

One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Description : One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Last Answer : Answer: D

When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes

Description : When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes

Last Answer : Answer: B

When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Description : When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Last Answer : Answer: C

When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Description : When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Last Answer : Answer: D

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

In an impressed current cathodic protection system, the anode is ____________. A. connected to the hull and deteriorates with time B. insulated from the hull and does not waste away C. connected to the hull but does not waste away D. insulated from the hull but deteriorates with time

Description : In an impressed current cathodic protection system, the anode is ____________. A. connected to the hull and deteriorates with time B. insulated from the hull and does not waste away C. connected to the hull but does not waste away D. insulated from the hull but deteriorates with time

Last Answer : Answer: B

A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Description : A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Last Answer : Answer: B

A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Description : A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Last Answer : Answer: D

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

Locations where Gas Insulated Substation is preferred

Description : Locations where Gas Insulated Substation is preferred

Last Answer : Gas Insulated Substations are preferred in the places where land requirement for the substation is difficult such as in populated areas and highly polluted areas where outdoor switchyard is not ... pollution and saline environment. Under such case indoor GIS substation is very much helpful.

Gas Insulated Substations Advantages Disadvantages

Description : Gas Insulated Substations Advantages Disadvantages

Last Answer : Gas Insulated Substations (GIS): Gas Insulated Substations (GIS) are differ from Air Insulated Substations (substations we usually see) such that all the substation equipment such as busbars, circuit breakers ... in the pressure of the SF6 gas in any module results in flash overs and faults

What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Description : What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Last Answer : C. Quad

A long iron rod initially at a temperature of 20°C has one end dipped in boiling water (100°C) at time, t = 0. The curved surface of the rod is insulated so that heat conduction is one dimensional in the axial direction. The temperature at a distance 100 mm from the dipped end becomes 40°C at time, t = 200 s. The same temperature is achieved at a distance of 200 mm from the dipped end at time (A) t = 283 s (B) t = 356 s (C) t = 400 s (D) t = 800 s

Description : A long iron rod initially at a temperature of 20°C has one end dipped in boiling water (100°C) at time, t = 0. The curved surface of the rod is insulated so that heat conduction is one dimensional in the axial direction. The ... = 283 s (B) t = 356 s (C) t = 400 s (D) t = 800 s

Last Answer : (D) t = 800 s

Define insulated wire.

Description : Define insulated wire. 

Last Answer : Insulated wire: A conductor or multi-stranded conductor which has a insulating material on it is called a insulated wire. 

Define unprotected insulated wire.

Description : Define unprotected insulated wire. 

Last Answer : Unprotected insulated wire: Unprotected insulated wire is which the insulation of the wire is not covered by a protective sheathing to prevent it from mechanical damage. 

What are the parts of paper insulated lead covered cable?

Description : What are the parts of paper insulated lead covered cable?

Last Answer : a. Core. b. Insulation of cable. c. Metallic sheath. d. Bedding. e. Armouring. f. Serving.