A network is said to be under resonance when the voltage and the current at the network input terminals are

A network is said to be under resonance when the voltage and the current at the network input terminals are

(A) in phase

(B) out of phase

(C) in phase quadrature

(D) in phase, and have equal magnitudes
by

1 Answer

Answer :

A network is said to be under resonance when the voltage and the current at the network input terminals are in phase

by

Related questions

A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Last Answer : Solution

With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.

A network that consists of at least a voltage source or current source is called

Description : A network that consists of at least a voltage source or current source is called A) Active network B) Ideal network C) Sourced network D) Outsourced network

Last Answer : A network that consists of at least a voltage source or current source is called Active network

In parallel RLC resonance circuit at resonance the current will be

Description : In parallel RLC resonance circuit at resonance the current will be  (1) Minimum (2) Maximum (3) Zero (4) Infinite

Last Answer : In parallel RLC resonance circuit at resonance the current will be Minimum 

Magnitude of current at resonance in R-L-C circuit?

Description : Magnitude of current at resonance in R-L-C circuit?

Last Answer : The current will be maximum if it is a series rlc circuit.

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the

Description : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

Last Answer : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will not change

Which of the following theorems enables a number of voltage (or current) source to be combined directly into

Description : Which of the following theorems enables a number of voltage (or current) source to be combined directly into a single voltage (or current) source. (1) compensation theorem (2) reciprocity theorem (3) superposition theorem (4) Millman's theorem

Last Answer : Which of the following theorems enables a number of voltage (or current) source to be combined directly into a single voltage (or current) source. (1) compensation theorem (2) reciprocity theorem (3) superposition theorem (4) Millman's theorem

The internal resistances of an ideal current source, and an ideal voltage source are, respectively,

Description : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

Last Answer : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, ∞, 0

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

What kills, current or voltage?

Description : What kills, current or voltage?

Last Answer : Current would kill. You can actually have thousands of bolts going through you and not even know it. Yes you probably know already voltage is current times resistance. Since your body is a resistor it would take just a small amount of current to create a very high voltage

Why inductor current lags inductor voltage ?

Description : Why inductor current lags inductor voltage ?

Last Answer : Inductor is a wire wounding structure having a core material it induces emf which is opposite to the voltage supply and proportional to rate of change of current so current lags the voltage in inductor

Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Description : Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

Last Answer : When two alternating quantities attain their respective zero or peak values simultaneously, the quantities are said to be in-phase quantities. When the quantities do not attain their respective zero or ... current is leading the voltage or the voltage is said to be lagging behind the current.

Define: 1) voltage ratio, 2) current ratio, 3) transformation ratio of transformer.

Description : Define: 1) voltage ratio, 2) current ratio, 3) transformation ratio of transformer.

Last Answer : 1) Voltage ratio: The voltages in primary and secondary winding is proportional to number of turns in primary and secondary respectively. So, the voltage ratio is same as transformation ratio. V2/V1 = N2 ... as transformation ratio of transformer. It is denoted by K. K = N2/N1

Write the relation between phase and line current, phase and line voltage for Star connection.

Description : Write the relation between phase and line current, phase and line voltage for Star connection.

Last Answer : Line voltage is equal to root three times of phase voltage and line and phase currents are equal in star connection

A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Step-down transformer converts high voltage and low current into:

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Last Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

Which of the following is the least expensive protection for over current in low voltage system?

Description : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

Last Answer : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

A current controlled voltage source is equivalent to :

Description : A current controlled voltage source is equivalent to :  (A) series voltage feed -back amplifier (B) shunt current feed -back amplifier (C) shunt voltage feed -back amplifier (D) series current feed -back amplifier

Last Answer : A current controlled voltage source is equivalent to : shunt voltage feed -back amplifier

In order that current should flow without causing excessive heating or voltage drop, the relay contacts should?

Last Answer : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should have low contact resistance, be clean and smooth, be of sufficient size and proper shape.

Why does increase in current mean a decrease in voltage?

Description : Why does increase in current mean a decrease in voltage?

Last Answer : This is because current flows from high potential to low potential to bring the two diffrent potential to unity , thus  a reduced potential (voltage)

according to ohms law voltage directly proportional to current but it is reverse in transformer why?

Description : About trnsformer

Last Answer : Acc to Ohms law V=IR but it is only applicable when our resistance R is constant, as in case of transformer we take impedence which is equivalent to resistance is not constant it varies with system parameters that why Ohms law not applicable in case of transformer

Which is the reason to electrical shock voltage/current?

Description : Electrical shock happens for voltage/current?

Last Answer : The severity ofelectric shockdepends on thecurrentflowing through the body, which is a function of the electromotive force (E) involts, and the contact resistance (R) in ohms.

How to Clean Car Battery Terminals

Description : How to Clean Car Battery Terminals

Last Answer : How to Clean Car Battery Terminals How to Paint a Car One of the most common causes of false starts and poor performance in many automobiles is when car battery terminals get dirty or corroded. ... these simple steps, you never have to pay big money to replace your battery and terminals again.

The number of terminals present in IGBT is

Description : The number of terminals present in IGBT is A) 2 B) 3 C) 4 D) 5

Last Answer : The number of terminals present in IGBT is 3

If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded

Description : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) ... side  (D) zero sequence currents are present on the primary side but not on the secondary side

Last Answer : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

____are the conductors, which connect the consumer's terminals to the distribution.

Last Answer : Service mains are the conductors, which connect the consumer's terminals to the distribution.

A MOSFET has how many terminals?

Description : A MOSFET has how many terminals?

Last Answer : A MOSFET having three terminals 1st one is Gate (insulated), 2nd one is Source and 3rd one is Drain.

BJT have how many terminals?

Last Answer : BJT have three terminals Base, emitter and collector.

thyristor have how many terminals?

Last Answer : Thyristor have three terminals anode, cathode and Gate.

Diode have how many terminals?

Last Answer : Diode have two terminals.

Define Resonance.

Description : Define Resonance. 

Last Answer : When the frequency of the external periodic force applied to a body is exactly equal to ( matches) natural frequency of body, the body vibrates with maximum amplitude, the effect is known as resonance 

Which of the following is true at resonance in LC circuits?

Description : Which of the following is true at resonance in LC circuits? A) The series impedance of the two elements is at a maximum and the parallel impedance is at minimum B) The series impedance of the ... D) The series impedance of the two elements is at a minimum and the parallel impedance is at maximum

Last Answer : Which of the following is true at resonance in LC circuits? A) The series impedance of the two elements is at a maximum and the parallel impedance is at minimum B) The series impedance of ... D) The series impedance of the two elements is at a minimum and the parallel impedance is at maximum

The series and parallel resonance on L-C circuit differs in that?

Description : The series and parallel resonance on L-C circuit differs in that?

Last Answer : The series and parallel resonance on L-C circuit differs in that series resistance needs a low-resistance source for sharp rise in current.

A parallel AC. circuit in resonance will?

Description : A parallel AC. circuit in resonance will?

Last Answer : A parallel AC. circuit in resonance will have a high impedance.

The purpose of a parallel circuit resonance is to magnify?

Description : The purpose of a parallel circuit resonance is to magnify?

Last Answer : The purpose of a parallel circuit resonance is to magnify voltage.

In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Description : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Last Answer : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of L or C.

The power factor at resonance in R-L- C parallel circuit is?

Description : The power factor at resonance in R-L- C parallel circuit is?

Last Answer : since a rlc circuit at resonance behaves like a pure resistive circuit, i.e there is no phase difference between current and voltage, hence the power factor is unity.

When a voltage of one volt is applied, a circuit allows one micro ..

Description : When a voltage of one volt is applied, a circuit allows one micro ampere current to flow through it. The conductance of the circuit is?

Last Answer : If v = 1 volt and i = 1 micro amp, i= 10^(-6)   So R = V/I,  R= 1/10^(-6) , R= 10^6  And now Conductance G = 1/R  So G = 10^(-6) mho..... Answer

Explain Briefly The Trap Input For The 8085.?

Description : Explain Briefly The Trap Input For The 8085.?

Last Answer : Answer :The TRAP input is sensitive to both edge and level. The pulse width for this signal should be in excess as compared to the normal noise width. A second trap will never be able to ... to low transition. The pulse widths are wider than normal widths so as to prevent unwanted false triggers.

What Are Input & Output Devices?

Description : What Are Input & Output Devices?

Last Answer : Answer :Keyboards, Floppy disk are the examples of input devices. Printer, LED / LCD display, CRT Monitor are the examples of output devices.

How to Fix a Laptop Power Input

Description : How to Fix a Laptop Power Input

Last Answer : How to Fix a Laptop Power Input Besides extra battery chargers, your laptop charges the battery through the DC jack found at the side of the laptop case. Often, it is not the battery or the ... , it's best to check your warranty for instructions on where you should take the laptop for repair.

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Description : Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Last Answer : 1. In positive half cycle (0 to Π): The end A of the secondary winding becomes positive and end B negative. This makes diode D1 and D4 forward biased while diode D2 and D3 are reverse biased. These two diodes will ... D2 and D3 when it is conducting is as follows.  B - D2 - RL - D3 - A 

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Description : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Last Answer : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be 2 watts

The largest change of input quantity for which there is no output of instrument is called ______

Description : The largest change of input quantity for which there is no output of instrument is called ______ A) Dead time B) Dead input C) Dead output D) Dead zone

Last Answer : The largest change of input quantity for which there is no output of instrument is called Dead zone

Is the input impedance of MOSFET more than BJT and FET?

Description : Is the input impedance of MOSFET more than BJT and FET?

Last Answer : Yes, the input impedance of MOSFET more than BJT and FET.

what is gate turn off thyristor (GTO)?

Description : Draw the structural diagram of GTO. Explain briefly the switching behavior of GTO with the help of appropriate voltage and current waveform.

Last Answer : Gate Turn Off Thyristor (GTO) Conventional Thyristor can be turned on with gate terminal but can not turn off from gate terminal. But in case of Gate Turn Off Thyristor (GTO), we can turn it on and off ... subdivided as storage period (Ts), fall period (Tp) and tail period (Tt).

An a.c series circuit has resistance of 10ohm, inductance of 0.1H and capacitance of 10µf, voltage applied to circuit is 200V. find (i) Resonant frequency (ii) Current at resonance (iii) Power at resonance

Description : An a.c series circuit has resistance of 10ohm, inductance of 0.1H and capacitance of 10µf, voltage applied to circuit is 200V. find (i) Resonant frequency (ii) Current at resonance (iii) Power at resonance 

Last Answer : Solution: For RLC series circuit

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC

Description : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

Last Answer : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the C only

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system