To cover the greatest distance when gliding, the gliding speed must be: a. Near to the stalling speed b. As high as possible within VNE limits c. About 30% faster than Vmd d. The one that gives the highest L/D ratio

To cover the greatest distance when gliding, the gliding speed must be:  
a. Near to the stalling speed  
b. As high as possible within VNE limits  
c. About 30% faster than Vmd  
d. The one that gives the highest L/D ratio
by

1 Answer

Answer :

d. The one that gives the highest L/D ratio
by

Related questions

Which of the following would give the greatest gliding performance? a. Flight at VMD b. Flight at 1.32VMD c. Flight at the best CL/CD ratio d. Flight close to CL MAX

Description : Which of the following would give the greatest gliding performance? a. Flight at VMD b. Flight at 1.32VMD c. Flight at the best CL/CD ratio d. Flight close to CL MAX

Last Answer : d. Flight close to CL MAX

Which of the following would give the greatest gliding performance? a. Flight at VMD b. Flight at 1.32VMD c. Flight at the best CL/CD ratio d. Flight close to CL MAX

Description : Which of the following would give the greatest gliding performance? a. Flight at VMD b. Flight at 1.32VMD c. Flight at the best CL/CD ratio d. Flight close to CL MAX

Last Answer : d. Flight close to CL MAX

A stall warning device must be set to operate: a. At the stalling speed b. At a speed just below the stalling speed c. At a speed about 5% to 10% above the stalling speed d. At a speed about 20% above the stalling speed

Description : A stall warning device must be set to operate: a. At the stalling speed b. At a speed just below the stalling speed c. At a speed about 5% to 10% above the stalling speed d. At a speed about 20% above the stalling speed

Last Answer : c. At a speed about 5% to 10% above the stalling speed

The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce the approach angle to 1.5deg (150ft/mile), add 15kts to all speeds, keep the aeroplane clean (no flaps or gear) and fly it into the surface c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Description : The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce ... d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Last Answer : c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first

The best EAS/Drag ratio is approximately: a. 1.3 VMD b. 1.32 VMD c. 1.6 VMD d. 1.8 VMD

Description : The best EAS/Drag ratio is approximately: a. 1.3 VMD b. 1.32 VMD c. 1.6 VMD d. 1.8 VMD

Last Answer : b. 1.32 VMD

The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Description : The maximum induced drag occurs at a speed of: a. VMD b. VMP c. VSO d. VATO

Last Answer : c. VSO

An aircraft has a stalling speed in level flight of 70kt IAS. In a 60° balanced turn, the stalling speed would be: a. 76kt b. 84kt c. 99kt d. 140kt

Description : An aircraft has a stalling speed in level flight of 70kt IAS. In a 60° balanced turn, the stalling speed would be: a. 76kt b. 84kt c. 99kt d. 140kt

Last Answer : c. 99kt

If the stalling speed in a 15 degree bank turn is 60kt, what would the stall speed be in a 45 degree bank? a. 83kt b. 70kt c. 85kt d. 60kt

Description : If the stalling speed in a 15 degree bank turn is 60kt, what would the stall speed be in a 45 degree bank? a. 83kt b. 70kt c. 85kt d. 60kt

Last Answer : b. 70kt

The stalling speed of an aeroplane is most affected by: a. Changes in air density b. Variations in aeroplane loading c. Variations in flight altitude d. Changes in pitch attitude

Description : The stalling speed of an aeroplane is most affected by: a. Changes in air density b. Variations in aeroplane loading c. Variations in flight altitude d. Changes in pitch attitude

Last Answer : b. Variations in aeroplane loading

If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Description : If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Last Answer : d. Remains the same, but rate of descent increases

A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to caster freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Description : A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to ... freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Last Answer : b. Allows the nosewheel to caster within preset limits about the neutral position

An aeroplane of 110,000kg has its CG at 22.6m aft of the datum. The CG limits are 18m to 22m aft of the datum. How much mass must be removed from a hold 30m aft of the datum to bring the CG to its mid point? a. 26,800 kg b. 28,600 kg c. 86,200 kg d. 62,800 kg

Description : An aeroplane of 110,000kg has its CG at 22.6m aft of the datum. The CG limits are 18m to 22m aft of the datum. How much mass must be removed from a hold 30m aft of the datum to bring the CG to its mid point? a. 26,800 kg b. 28,600 kg c. 86,200 kg d. 62,800 kg

Last Answer : b. 28,600 kg

Where is wind shear the greatest? a. Near a strong low level inversion and in the region of a thunderstorm b. Near a valley with wind speeds greater than 35kts c. On the windward side of a mountain d. When the wind is greater than 35kts

Description : Where is wind shear the greatest? a. Near a strong low level inversion and in the region of a thunderstorm b. Near a valley with wind speeds greater than 35kts c. On the windward side of a mountain d. When the wind is greater than 35kts

Last Answer : a. Near a strong low level inversion and in the region of a thunderstorm

Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Description : Which stall has the greatest angle of attack? a. Low speed stall b. High speed stall (shock stall) c. Deep stall d. Accelerated stall

Last Answer : c. Deep stall

t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Description : t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Last Answer : a. will be unchanged but ground speed will be faster

By what percentage should V2 be greater than VMCA? a. 30% b. 10% c. 20% d. 15%

Description : By what percentage should V2 be greater than VMCA? a. 30% b. 10% c. 20% d. 15%

Last Answer : b. 10%

A flight is planned from L to M, distance 850 nm. Wind component out is 35 kt(TWC), TAS 450kt. Mean fuel flow out is 2500kg/hr, mean fuel flow inbound is 1900kg/hr and the fuel available is 6000kg. The time and distance to PSR is: a. 1hr 30 min, 660nm b. 1hr 30 min, 616nm c. 1hr 15 min, 606nm d. 1hr 16 min, 616nm

Description : A flight is planned from L to M, distance 850 nm. Wind component out is 35 kt(TWC), TAS 450kt. Mean fuel flow out is 2500kg/hr, mean fuel flow inbound is 1900kg/hr and the fuel available is 6000kg. The time ... 30 min, 660nm b. 1hr 30 min, 616nm c. 1hr 15 min, 606nm d. 1hr 16 min, 616nm

Last Answer : d. 1hr 16 min, 616nm

What is the rule concerning level or height the aircraft should maintain when flying IFR outside controlled airspace unless otherwise directed? a. 2,000 feet above the highest obstacle within 8kms of the heading b. 1,000 feet above the highest obstacle within 8kms of the estimated position of the aircraft c. 1,000 feet above the highest obstacle within 8kms of the planned track d. 2,000 feet above the highest obstacle within 8kms of the planned track

Description : What is the rule concerning level or height the aircraft should maintain when flying IFR outside controlled airspace unless otherwise directed? a. 2,000 feet above the highest obstacle within 8kms of ... planned track d. 2,000 feet above the highest obstacle within 8kms of the planned track

Last Answer : b. 1,000 feet above the highest obstacle within 8kms of the estimated position of the aircraft

What are the VMC limits for Class B airspace? a. 8km flight visibility, clear of cloud and in sight of the surface b. 8km flight visibility, 1000ft vertically and 1500m horizontally from cloud c. 5km flight visibility, 1000ft vertically and 1500m horizontally from cloud d. The same as Class D

Description : What are the VMC limits for Class B airspace? a. 8km flight visibility, clear of cloud and in sight of the surface b. 8km flight visibility, 1000ft vertically and 1500m horizontally from ... . 5km flight visibility, 1000ft vertically and 1500m horizontally from cloud d. The same as Class D

Last Answer : d. The same as Class D

When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Description : When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Last Answer : a. Rapid descent when AC descends below cabin altitude

An aircraft has a L/D ratio of 15:1 at 50kts in calm air. What would the L/D ratio be with a direct headwind of 25kts? a. 30:1 b. 15:1 c. 25:1 d. 7.5:1

Description : An aircraft has a L/D ratio of 15:1 at 50kts in calm air. What would the L/D ratio be with a direct headwind of 25kts? a. 30:1 b. 15:1 c. 25:1 d. 7.5:1

Last Answer : b. 15:1

The normal serum value for potassium is a) 3.5-5.5 mEq/L. Serum potassium must be within normal limits to prevent cardiac dysrhythmias. b) 135-145 mEq/L. Normal serum sodium is 135-145 mEq/L. c) 96-106 mEq/L. Normal serum chloride is 96-106 mEq/L. d) 8.5-10.5 mg/dL. Normal total serum calcium is 8.5-10.5mg/dL.

Description : The normal serum value for potassium is a) 3.5-5.5 mEq/L. Serum potassium must be within normal limits to prevent cardiac dysrhythmias. b) 135-145 mEq/L. Normal serum sodium is 135-145 mEq/L. c) 96-106 mEq/L. ... is 96-106 mEq/L. d) 8.5-10.5 mg/dL. Normal total serum calcium is 8.5-10.5mg/dL.

Last Answer : a) 3.5-5.5 mEq/L. Serum potassium must be within normal limits to prevent cardiac dysrhythmias.

To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Description : To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Last Answer : b. Increase angle of attack to maintain the correct lift force

If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Description : If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Last Answer : b. increased

If the centre distance of the mating gears having involute teeth is varied within limits, the velocity ratio (A) Increases (B) Decreases (C) Remains unchanged (D) None of these

Description : If the centre distance of the mating gears having involute teeth is varied within limits, the velocity ratio (A) Increases (B) Decreases (C) Remains unchanged (D) None of these

Last Answer : (C) Remains unchanged

An aeroplane is starting a non-precision approach with an MDH of 250ft and minimum visibility of 800 meters. ATC gives threshold, mid-runway and final third RVRs. When may the approach be started? a. When threshold and mid-runway RVRs are greater than 800m b. When all 3 RVRs are greater than 800m c. When the met viz is greater than 800m. RVR is for precision approaches only. d. When threshold RVR is greater than 800m

Description : An aeroplane is starting a non-precision approach with an MDH of 250ft and minimum visibility of 800 meters. ATC gives threshold, mid-runway and final third RVRs. When may the approach be started? ... than 800m. RVR is for precision approaches only. d. When threshold RVR is greater than 800m

Last Answer : d. When threshold RVR is greater than 800m

The illusion that the aircraft is taxiing too fast can be caused by: a. Snow and a tailwind b. Snow and a headwind c. Rain and a headwind d. An unaccustomed high distance of the cockpit from the ground

Description : The illusion that the aircraft is taxiing too fast can be caused by: a. Snow and a tailwind b. Snow and a headwind c. Rain and a headwind d. An unaccustomed high distance of the cockpit from the ground

Last Answer : c. Rain and a headwind

Which of the following would give the greatest gliding endurance?

Description : Which of the following would give the greatest gliding endurance?

Last Answer : Flight close to CL MAX

Which of the following conditions is worst with regard to wake vortex turbulence? a. Lights winds near the surface b. Strong winds near the surface c. Marked vertical wind shear d. Marked atmospheric turbulence near the ground

Description : Which of the following conditions is worst with regard to wake vortex turbulence? a. Lights winds near the surface b. Strong winds near the surface c. Marked vertical wind shear d. Marked atmospheric turbulence near the ground

Last Answer : a. Lights winds near the surface

The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Description : The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Last Answer : c. The elevators

True track 215; mountain elevation 11,600ft; local airfield gives QNH as 1035mb; required terrain clearance 1500ft; temperature ISA -15C. Which of the following is the minimum flight level considering the temperature? a. FL150 b. FL140 c. FL120 d. FL110

Description : True track 215; mountain elevation 11,600ft; local airfield gives QNH as 1035mb; required terrain clearance 1500ft; temperature ISA -15C. Which of the following is the minimum flight level considering the temperature? a. FL150 b. FL140 c. FL120 d. FL110

Last Answer : b. FL140

A cylinder head temperature gauge measures: a. The temperature of the hottest cylinder b. The temperature of all the cylinders and gives an average reading c. The temperature of the coolest cylinder d. The temperature of the two cylinders furthest away from each other divided by two

Description : A cylinder head temperature gauge measures: a. The temperature of the hottest cylinder b. The temperature of all the cylinders and gives an average reading c. The temperature of the coolest cylinder d. The temperature of the two cylinders furthest away from each other divided by two

Last Answer : a. The temperature of the hottest cylinder

After an act of unlawful interference a report is to be made. When and to whom? a. Within 10 days and to the Authority of the State of Registry b. Immediately and to the Authority of the State of the airspace in which the event occurred c. Without delay, to the designated local authority and the Authority of the State of Registration d. Without delay, to the designated local authority and the Authority of the State of the Operator

Description : After an act of unlawful interference a report is to be made. When and to whom? a. Within 10 days and to the Authority of the State of Registry b. Immediately and to the Authority of ... d. Without delay, to the designated local authority and the Authority of the State of the Operator

Last Answer : d. Without delay, to the designated local authority and the Authority of the State of the Operator

What is the currency requirement for a pilot? a. 3 take-offs and landings on an aeroplane of the same type within the last 90 days b. 3 take-offs and landings on an aeroplane of the same type within the last 60 days c. 3 take-offs and landings on an aeroplane of the same type or approved simulator within the last 90 days d. 3 take-offs and landings on an aeroplane of the same type or approved simulator within the last 60 days

Description : What is the currency requirement for a pilot? a. 3 take-offs and landings on an aeroplane of the same type within the last 90 days b. 3 take-offs and landings on an aeroplane of the same ... 3 take-offs and landings on an aeroplane of the same type or approved simulator within the last 60 days

Last Answer : c. 3 take-offs and landings on an aeroplane of the same type or approved simulator within the last 90 days

The range indicated by DME is considered to be accurate within: a. 3% of range b. 1.25% of range c. 0.5nm d. ±0.25nm ±1.25% of range

Description : The range indicated by DME is considered to be accurate within: a. 3% of range b. 1.25% of range c. 0.5nm d. ±0.25nm ±1.25% of range

Last Answer : d. ±0.25nm ±1.25% of range

Where do you find the majority of the air within the atmosphere? a. Troposphere b. Stratosphere c. Tropopause d. Mesosphere

Description : Where do you find the majority of the air within the atmosphere? a. Troposphere b. Stratosphere c. Tropopause d. Mesosphere

Last Answer : a. Troposphere

You make a diversion from the route given in the flight plan and land at an uncontrolled airfield. Within what time after landing should you inform ATC? a. 10 mins b. 20 mins c. 30 mins d. 45 mins

Description : You make a diversion from the route given in the flight plan and land at an uncontrolled airfield. Within what time after landing should you inform ATC? a. 10 mins b. 20 mins c. 30 mins d. 45 mins

Last Answer : c. 30 mins

Following a communications failure, the time at which the aircraft should aim to leave the hold is: a. Within 10 minutes of the EAT or ETA b. Within 30 minutes of the EAT or ETA c. EAT or ETA d. Before it runs out of fuel

Description : Following a communications failure, the time at which the aircraft should aim to leave the hold is: a. Within 10 minutes of the EAT or ETA b. Within 30 minutes of the EAT or ETA c. EAT or ETA d. Before it runs out of fuel

Last Answer : c. EAT or ETA

The MSA provides 300m obstacle clearance within how many miles radius of the navigation facility at the aerodrome? a. 20nm b. 30nm c. 25nm d. 15nm

Description : The MSA provides 300m obstacle clearance within how many miles radius of the navigation facility at the aerodrome? a. 20nm b. 30nm c. 25nm d. 15nm

Last Answer : c. 25nm

During a straight departure, the initial track is to be: a. Within 5° of runway centre-line b. Within 10 of runway centre-line c. Within 15° of runway centre-line d. Within 25° of runway centre-line

Description : During a straight departure, the initial track is to be: a. Within 5° of runway centre-line b. Within 10 of runway centre-line c. Within 15° of runway centre-line d. Within 25° of runway centre-line

Last Answer : c. Within 15° of runway centre-line

Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless of the direction from which B approaches b. Aircraft B, regardless of the direction from which A approaches c. Aircraft A, if B is to the right of him d. Aircraft B, if A is to the left of him

Description : Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless ... , if B is to the right of him d. Aircraft B, if A is to the left of him

Last Answer : d. Aircraft B, if A is to the left of him

The Vertical Separation Minimum (VSM) for flights in accordance with IFR within controlled airspace below FL290 is: a. 500 feet (150m) b. 2500 feet (750 m) c. 1000 feet (300m) d. 2000 feet (600m)

Description : The Vertical Separation Minimum (VSM) for flights in accordance with IFR within controlled airspace below FL290 is: a. 500 feet (150m) b. 2500 feet (750 m) c. 1000 feet (300m) d. 2000 feet (600m)

Last Answer : c. 1000 feet (300m)

When the aircraft carries serviceable Mode C transponder, the pilot shall continuously operate this mode: a. Only when directed by ATC b. Unless otherwise directed by ATC c. Only when the aircraft is flying within controlled airspace d. Regardless of ATC instructions

Description : When the aircraft carries serviceable Mode C transponder, the pilot shall continuously operate this mode: a. Only when directed by ATC b. Unless otherwise directed by ATC c. Only when the aircraft is flying within controlled airspace d. Regardless of ATC instructions

Last Answer : b. Unless otherwise directed by ATC

Pilots are not allowed to use the indent function on their SSR, unless: a. They operate outside controlled airspace b. If asked by ATC c. Within controlled airspace d. They operate a transponder with mode C

Description : Pilots are not allowed to use the indent function on their SSR, unless: a. They operate outside controlled airspace b. If asked by ATC c. Within controlled airspace d. They operate a transponder with mode C

Last Answer : b. If asked by ATC

A DISTRESS message differs from an URGENCY message because: a. There is grave and imminent danger which requires immediate assistance b. The aeroplane has suffered damage that endangers the ability to fly c. The aeroplane will not be able to reach a suitable aerodrome d. The situation concerns the safety of passengers on board or within sight

Description : A DISTRESS message differs from an URGENCY message because: a. There is grave and imminent danger which requires immediate assistance b. The aeroplane has suffered damage that endangers the ... suitable aerodrome d. The situation concerns the safety of passengers on board or within sight

Last Answer : a. There is grave and imminent danger which requires immediate assistance

If the track on an instrument departure is published, the pilot is expected to: a. Correct for the correct wind so as to stay within controlled airspace b. Ask ATC for another heading to steer correcting for wind c. Ignore the wind and proceed with a heading equal to the track d. Ask ATC for permission to correct heading for wind

Description : If the track on an instrument departure is published, the pilot is expected to: a. Correct for the correct wind so as to stay within controlled airspace b. Ask ATC for another heading to steer ... proceed with a heading equal to the track d. Ask ATC for permission to correct heading for wind

Last Answer : a. Correct for the correct wind so as to stay within controlled airspace

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

The purpose of a trim tab is: a. To assist the pilot in initiating movement of the controls b. To zero the load on the pilot controls in the flight attitude required c. To provide feel to the controls at high speed d. To increase the effectiveness of the controls

Description : The purpose of a trim tab is: a. To assist the pilot in initiating movement of the controls b. To zero the load on the pilot controls in the flight attitude required c. To provide feel to the controls at high speed d. To increase the effectiveness of the controls

Last Answer : b. To zero the load on the pilot controls in the flight attitude required

What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Description : What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Last Answer : d. To reduce wing twist at high speed

Where a medium category aeroplane is landing behind a heavy category aeroplane, the minimum separation distance in NM is: a. 3 b. 4 c. 5 d. 6

Description : Where a medium category aeroplane is landing behind a heavy category aeroplane, the minimum separation distance in NM is: a. 3 b. 4 c. 5 d. 6

Last Answer : c. 5