A post weld heat treatment may also be of benefit in minimizing the risk of weld decay, this heat treatment would be called? a) Stress relief b) Normalizing c) Quench and Tempering d) Solution treatment over 1000 °C

A post weld heat treatment may also be of benefit in minimizing the risk of weld decay, this heat treatment would be  called?
a) Stress relief b) Normalizing c) Quench and Tempering d) Solution treatment over 1000 °C
by

1 Answer

Answer :

d) Solution treatment over 1000 °C
by

Related questions

Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Description : Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Last Answer : (B) Stress relieving

Explain: i) Normalizing ii) Tempering

Description : Explain: i) Normalizing ii) Tempering

Last Answer : Normalizing:- It is similar to annealing. The process consists of heating the steel to a definite temperature about 500C above the critical temperature. Then it is allowed to cool freely in air. The cooling ... to a definite temperature (200 - 6000C) & then cooling it at a suitable rate.

Why is post-weld heat treatment (stress relieving) sometimes necessary for welded vessels?

Description : Why is post-weld heat treatment (stress relieving) sometimes necessary for welded vessels?

Last Answer : During the welding process, the two metal pieces being joined are subject to extreme temperatures and can cause the crystalline structure of the metal to pass through various metallurgical phases. As a ... composition of the metals. Holding temperatures can range from 1100-1350 °F (593- 732 °C).

What is meant by the term PWHT? a) Pipe weld heat treatment b) Pre weld heat treatment c) Post weld hydrogen tearing d) Post weld het treatment

Description : What is meant by the term PWHT? a) Pipe weld heat treatment b) Pre weld heat treatment c) Post weld hydrogen tearing d) Post weld het treatment

Last Answer : d) Post weld het treatment

The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing

Description : The heat treatment process applied to cold formed steel parts is (A) Normalising (B) Tempering (C) Artificial ageing (D) Solution annealing

Last Answer : (D) Solution annealing

Weld decay can be minimized by specifying steel with: a) Higher carbon level b) higher chromium level c) lower carbon level d) lower chromium level

Description : Weld decay can be minimized by specifying steel with: a) Higher carbon level b) higher chromium level c) lower carbon level d) lower chromium level

Last Answer : c) lower carbon level

Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Description : Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Last Answer : a) A reduced resistance to corrosion

Weld decay is caused by the formation of a compound with carbon. The other element in this compound is: a) Manganese b) Sulphur c) Chromium d) Nickel

Description : Weld decay is caused by the formation of a compound with carbon. The other element in this compound is: a) Manganese b) Sulphur c) Chromium d) Nickel

Last Answer : c) Chromium

Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Description : Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Last Answer : d) Austenitic stainless steels

When welding medium carbon steel plates over 100mm in thickness would the basic electrodes require any pre treatment before use? a) None if they were in a vacuum pack opened 8 hours prior to use b) None if they were in a sealed vacuum pack prior to use c) Heat to 500 °C for 2 hours if used outside d) Baked at 150°C for 4hours prior to use

Description : When welding medium carbon steel plates over 100mm in thickness would the basic electrodes require any pre treatment before use? a) None if they were in a vacuum pack opened 8 hours prior to use b) None if ... ) Heat to 500 °C for 2 hours if used outside d) Baked at 150°C for 4hours prior to use

Last Answer : b) None if they were in a sealed vacuum pack prior to use

What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600

Description : What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600

Last Answer : (B) 200-300

Which of the following heat treatment processes is used for softening the hardened material? (A) Normalising (B) Tempering (C) Annealing (D) None of these

Description : Which of the following heat treatment processes is used for softening the hardened material? (A) Normalising (B) Tempering (C) Annealing (D) None of these

Last Answer : (B) Tempering

The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these

Description : The heat treatment process to which castings and the steel balls produced by cold heading are subjected is (A) Tempering (B) Normalising (C) Annealing (D) None of these

Last Answer : (B) Normalising

Which of the following heat treatment processes is usually applied to castings? (A) Tempering (B) Annealing (C) Normalising (D) Carburising

Description : Which of the following heat treatment processes is usually applied to castings? (A) Tempering (B) Annealing (C) Normalising (D) Carburising

Last Answer : (D) Carburising

In order to quench the are quickly and also optimize the dimensions generally

Description : In order to quench the are quickly and also optimize the dimensions generally   (a) Air blast C.B. is preferred (b) Oil C.B. is preferred (c) SF6 C.B. is preferred (d) Minimum oil C.B. is preferred  

Last Answer : In order to quench the are quickly and also optimize the dimensions generally SF6 C.B. is preferred

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

The main problem with such a heat treatment of stainless steel pipe spools and the reason why it is not regularly employed is: a) Controlling the rate of the temperature rise b) Controlling the cooling c) The length of the soak period d) High risk of distortion

Description : The main problem with such a heat treatment of stainless steel pipe spools and the reason why it is not regularly employed is: a) Controlling the rate of the temperature rise b) Controlling the cooling c) The length of the soak period d) High risk of distortion

Last Answer : d) High risk of distortion

Tempering of a material does not improve its (A) Machinability (B) Toughness (C) Internal stress level (D) Softness

Description : Tempering of a material does not improve its (A) Machinability (B) Toughness (C) Internal stress level (D) Softness

Last Answer : A) Machinability

In Herbert Simon's theory, a manager who accepts the first satisfactory solution to a problem has made a ______ decision, while a manager who continues to search for the best possible solution is seeking to find a ______ decision (a) Maximising; satisficing ; (b) Minimising; maximizing ; (c) Satisficing; maximising (d) Maximising; minimizing

Description : In Herbert Simon's theory, a manager who accepts the first satisfactory solution to a problem has made a ______ decision, while a manager who continues to search for the best possible solution is ... ; satisficing ; (b) Minimising; maximizing ; (c) Satisficing; maximising (d) Maximising; minimizing

Last Answer : (b) Minimising; maximizing ;

Which of the following is not a sulfonylurea but acts by analogous mechanism to bring about quick and brief insulin release that is useful for normalizing meal time glycaemic excursions in type 2 diabetes mellitus: A. Glimepiride B. Miglitol C. Repaglinide D. Rosiglitazone

Description : Which of the following is not a sulfonylurea but acts by analogous mechanism to bring about quick and brief insulin release that is useful for normalizing meal time glycaemic excursions in type 2 diabetes mellitus: A. Glimepiride B. Miglitol C. Repaglinide D. Rosiglitazone

Last Answer : C. Repaglinide

Describe the normalizing process with its purpose.

Description : Describe the normalizing process with its purpose. 

Last Answer : Normalizing: Normalizing is the heat treatment which involves heating of the given steel to austenite temperature range holding it and there after cooling to room temperature at slow rate of cooling, ... To obtain required mechanical properties. To relieve internal stresses in some cases. 

Distinguish between annealing and normalizing process.

Description : Distinguish between annealing and normalizing process.

Last Answer : Annealing Normalizing Less hardness, toughness  Slightly more hardness, toughness.  For plain carbon steel the microstructure shows pearlite  Microstructure shows more pearlite.  ... less uniform. Internal stresses are least.  Internal stresses are slightly more 

When the router runs out of buffer space, this is called ________. * Source Quench * Redirect * Information Request * Low Memory

Description : When the router runs out of buffer space, this is called ________. * Source Quench * Redirect * Information Request * Low Memory

Last Answer : Correct answer: A Source quench is the process where the destination router, or end internetworking device will “quench” the date from the “source”, or the source router. This usually happens when the destination router runs out of buffer space to process packets.

The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C. (A) 768 (B) 908 (C) 1400 (D) 1539

Description : The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C. (A) 768 (B) 908 (C) 1400 (D) 1539

Last Answer : Option A

The following apply to use of spironolactone in CHF except: A. It is indicated only in NYHA class III/IV cases as additional drug to conventional therapy B. It affords prognostic benefit in severe heart failure over and above that afforded by ACE inhibitors C. It helps overcome refractoriness to diuretics D. It affords rapid symptomatic relief

Description : The following apply to use of spironolactone in CHF except: A. It is indicated only in NYHA class III/IV cases as additional drug to conventional therapy B. It affords prognostic benefit in ... by ACE inhibitors C. It helps overcome refractoriness to diuretics D. It affords rapid symptomatic relief

Last Answer : D. It affords rapid symptomatic relief

Why doesn't tea quench my thirst?

Description : Why doesn't tea quench my thirst?

Last Answer : answer:Much of our tea contains the compound tannin - which can cause dryness in your mouth. The astringency of tannin can make your mouth/throat feel dry - this depends on how strong the brew is. It tricks ... I get that as well (also when I drink iced-tea). I hope I explained it sufficiently. :)

Does an e-cigarette quench a regular cigarette?

Description : Does a chromium cigarette have an ojan effect like regular cigarettes?

Last Answer : Yes, it's effective.

Which protocol carries messages such as destination Unreachable, Time Exceeded, Parameter Problem, Source Quench, Redirect, Echo, Echo Reply, Timestamp, Information Request, Information Reply, Address Request, and Address Reply? * ICMP * UDP * TCP * TFTP

Description : Which protocol carries messages such as destination Unreachable, Time Exceeded, Parameter Problem, Source Quench, Redirect, Echo, Echo Reply, Timestamp, Information Request, Information Reply, Address Request, and Address Reply? * ICMP * UDP * TCP * TFTP

Last Answer : Correct answer: A ICMP (Internet Control Message Protocol) is a network layer internet protocol described in RFC # 792. ICMP reports IP packet information such as destination Unreachable, Time ... Echo Reply, Timestamp, Information Request, Information Reply, Address Request, and Address Reply.

Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Description : Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Last Answer : (A) 7 kgf/cm2 and 70 °C

Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000

Description : Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000

Last Answer : (B) 200-330

Ceramic recuperators (made of SiC) is economical, only when used for preheating combustion air above __________ °C. (A) 250 (B) 650 (C) 850 (D) 1000

Description : Ceramic recuperators (made of SiC) is economical, only when used for preheating combustion air above __________ °C. (A) 250 (B) 650 (C) 850 (D) 1000

Last Answer : (B) 650

Fusion point of coal ash generally varies from 1000 to 1700° C. Ash having fusion point less than __________ °C is liable to form clinker. (A) 1100 (B) 1250 (C) 1350 (D) 1400

Description : Fusion point of coal ash generally varies from 1000 to 1700° C. Ash having fusion point less than __________ °C is liable to form clinker. (A) 1100 (B) 1250 (C) 1350 (D) 1400

Last Answer : (A) 1100

Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are normally carried out at about __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Description : Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are ... __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Last Answer : (B) 900-1000

Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Description : Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Last Answer : (A) 700 - 1000

Conversion of yellow phosphorous to red phosphorous is done by heating it in covered retorts at __________ °C in absence of air. (A) 50-80 (B) 250-400 (C) 1000-1200 (D) 800-900

Description : Conversion of yellow phosphorous to red phosphorous is done by heating it in covered retorts at __________ °C in absence of air. (A) 50-80 (B) 250-400 (C) 1000-1200 (D) 800-900

Last Answer : (B) 250-400

Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C. (A) 80-120 (B) 200-300 (C) 600-800 (D) 1000-1100

Description : Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C. (A) 80-120 (B) 200-300 (C) 600-800 (D) 1000-1100

Last Answer : (D) 1000-1100

Temperature attained in soldering of metals is about __________ °C. (A) 150-300 (B) 400-500 (C) 650-800 (D) 1000-1100

Description : Temperature attained in soldering of metals is about __________ °C. (A) 150-300 (B) 400-500 (C) 650-800 (D) 1000-1100

Last Answer : (A) 150-300

Feed water usually at…… °C temperature. a) 70 b) 120 c) 1000 d) 80

Description : Feed water usually at…… °C temperature. a) 70 b) 120 c) 1000 d) 80

Last Answer : d) 80

Eradication of H.pylori along with gastric antisecretory drugs affords the following benefit(s): A. Faster relief of ulcer pain B. Faster ulcer healing C. Reduced chance of ulcer relapse D. Both ‘B’ and ‘C’ are correct

Description : Eradication of H.pylori along with gastric antisecretory drugs affords the following benefit(s): A. Faster relief of ulcer pain B. Faster ulcer healing C. Reduced chance of ulcer relapse D. Both ‘B’ and ‘C’ are correct

Last Answer : D. Both ‘B’ and ‘C’ are correct

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed

Description : Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed

Last Answer : b) 360/t

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Pick out the wrong statement. (A) Cold cracking of a weld is due to the presence of hydrogen gas in the weld (B) True stress is given by, σ = σE (1 + εE), where σE and εE are engineering stress and engineering strain respectively (C) Phosphorous can be easily recovered in the iron blast furnace (D) High residual stress at the surface is beneficial for fatigue properties of a material

Description : Pick out the wrong statement. (A) Cold cracking of a weld is due to the presence of hydrogen gas in the weld (B) True stress is given by, σ = σE (1 + εE), where σE and εE ... in the iron blast furnace (D) High residual stress at the surface is beneficial for fatigue properties of a material

Last Answer : Option C