Description : 8096 write-protected mode, no code can write to memory address between __. a) 2020 to 3FFFH b) 8000 to FFFFH c) 2000 to 3FFFH d) 2020 to 202FH 17. If the __ pin is ___ , then we have the option ... b) EA, low, internal, external c) EA, high, external, internal d) EA, low, external, internal
Last Answer : c) EA, high, external, internal
Description : In modes 2 and 3, if _____ bit of SCON bit is set will causes enable multiprocessor communication and is of ____ bit address. a) SM1, 9EH b) TB8 , 9CH c) SM2 , 9DH d) SM0, 9FH
Last Answer : c) SM2 , 9DH
Description : In an 8085 microprocessor, the instruction CMP B has been executed while the contentsof accumulator is less than that of register B. As a result carry flag and zero flag will berespectively (A) set, reset (B) reset, set (C) reset, reset (D) set, set
Last Answer : (A) set, reset
Description : In 8096, mode ____ of serial port are ___ modes commonly used for ____ communications. a) 1, 8bit, single processor b) 0, 7bit, multiple microcontroller c) 2, 9 bit, multiple processors d) 3, 8 bit, multiple microcontroller
Last Answer : a) 1, 8bit, single processor
Description : In 8096, CCB bit 3 is ____. a) write strobe mode select b) address valid strobe select c) bus width select d) Internal read control mode
Last Answer : c) bus width select
Last Answer : c) 2, 9 bit, multiple processors
Last Answer : b) address valid strobe select
Description : In 8255, under the I/O mode of operation we have __ modes. Under which mode will have the following features i) A 5 bit control port is available. ii) Three I/O lines are available at Port C. a) 3, Mode2 b) 2, Mode 2 c) 4, Mode 3 d) 3, Mode 2
Last Answer : a) 3, Mode2
Description : Which of the following instruction is used to set bit port directly? a) SET P1.0 b) MOV P1.0, bit c) SETB P1.0 d) JB P1.0, bit
Last Answer : JB P1.0, bit
Description : In 8086 the overflow flag is set when a) The sum is more than 16 bits b) Signed numbers go out of their range after an arithmetic operation c) Carry and sign flags are set
Last Answer : b) Signed numbers go out of their range after an arithmetic operation
Description : 8096 write-protected mode, no code can write to memory address between __. a) 2020 to 3FFFH b) 8000 to FFFFH c) 2000 to 3FFFH d) 2020 to 202FH
Last Answer : c) 2000 to 3FFFH
Description : Which of the following statements on DRAM are correct? i) Page mode read operation is faster than RAS read. ii) RAS input remains active during column address strobe. iii) The row and column addresses are strobed into the ... RAS and CAS inputs respectively. a) i & iii b) i & ii c) all d) iii
Last Answer : d) iii
Description : Which is not the main feature of DEC Alpha: a. 64 Bit RISC processor b. Designed to replace 32 VAX(CISC) c. Seven stage split integer/floating point pipeline d. Variable Instruction length
Last Answer : d. Variable Instruction length
Description : How many bit of instruction on our simple computer consist of one____: a. 2-bit b. 6-bit c. 12-bit d. None of these
Last Answer : c. 12-bit
Description : Which of the following instruction is of logical instructions? i) CPL A ii) JC rel iii) DA A iv) ANL A, Rn v) RR A vi) CPL bit a) i, v b) v, iii, I c) iv, ii d) v, iii, ii
Last Answer : c) iv, i
Description : A stack pointer is a. a 16-bit register in the microprocessor that indicate the beginning of the stack memory. b. a register that decodes and executes 16-bit arithmetic expression. c. The first memory location where a subroutine address is stored. d. a register in which flag bits are stored
Last Answer : a. a 16-bit register in the microprocessor that indicate the beginning of the stack memory.
Description : The 16 bit flag of 8086 microprocessor is responsible to indicate ___________ A. the condition of result of ALU operation B. the condition of memory C. the result of addition D. the result of subtraction
Last Answer : The 16 bit flag of 8086 microprocessor is responsible to indicate the condition of result of ALU operation
Description : Single address computer instruction has two parts: a. The operation code b. The operand c. A and B d. None of these
Last Answer : c. A and B
Description : In linear decoding address bus of 16-bit wide can connect only ____ of RAM. a. 16 KB b. 6KB c. 12KB d. 64KB
Last Answer : b. 6KB
Description : If the __ pin is ___ , then we have the option of using the ____ ROM or EPROM together with _____ memory and devices. a) EA, high, internal, external b) EA, low, internal, external c) EA, high, external, internal d) EA, low, external, internal
Last Answer : a) EA, high, internal, external
Description : __ bit in ICW1 indicates whether the 8259A is cascade mode or not? a) LTIM=0 b) LTIM=1 c) SNGL=0 d) SNGL=1
Last Answer : c) SNGL=0
Description : In 8279, a scanned sensor matrix mode, if a sensor changes its state, the ___ line goes ____ to interrupt the CPU. a) CS, high b) A0, high c) IRQ, high d) STB, high
Last Answer : c) IRQ, high
Description : In 8279 Strobed input mode, the control line goes low. The data on return lines is strobed in the ____. a) FIFO byte by byte b) FILO byte by byte c) LIFO byte by byte d) LILO byte by byte.
Last Answer : a) FIFO byte by byte
Description : 8096 has following features fill up the following, i) ____ Register file, ii) ____ I/O Ports iii) ____ architecture. a) 256 byte, five 8bit, register to register b) 256 byte, four 8bit, register ... c) 232 byte, five 8bit, register to register d) 232 byte, six 8 bit, register to register
Last Answer : c) 232 byte, five 8bit, register to register
Description : 8096 has following features fill up the following, i) ____ Register file, ii) ____ I/O Ports iii) ____ architecture. a) 256 byte, five 8bit, register to register b) 256 byte, four 8bit, ... c) 232 byte, five 8bit, register to register d) 232 byte, six 8 bit, register to register
Last Answer : d) 232 byte, six 8 bit, register to register
Description : In 8087, which instruction is used for division real reversed______. a) FDIV b) FIDIVR c) FDIVR d) FDIVRP
Last Answer : c) FDIVR
Description : In Unix, files can be protected by assigning each one a 9-bit mode called rights bits. Now, consider the following two statements: I. A mode of 641 (octal) means that the owner can read and write the file, other ... (B) Only II is correct (C) Both I and II are correct (D) Both I and II are incorrect
Last Answer : (C) Both I and II are correct
Description : How many operations are there in the instruction set of 8085 microprocessor?
Last Answer : There are 74 operations in the 8085 microprocessor.
Description : CISC stands for: a. Complex instruction set computer b. Camper instruct set of computer c. Compared instruction set computer d. None of these
Last Answer : a. Complex instruction set computer
Description : RISC stands for: a. Reduced Instruction set computer b. Reduced Instruct set compare c. Reduced instruction stands computer d. All of these 107. DEC stands for:
Last Answer : a. Reduced Instruction set computer
Description : ISA stands for: a. Instruct set area b. Instruction set architecture c. Both a and b d. None of these
Last Answer : b. Instruction set architecture
Description : RISC stands for: a. Reduced Instruction Set Computer b. Reduced Intergraded Set Computer c. Resource Instruction Set Computer d. Resource Instruction System Computer
Last Answer : a. Reduced Instruction Set Computer
Description : CISC stands for: a. Complex Instruction System Computer b. Complex Instruction Set Car c. Complex Instruction Set Computer d. None of these
Last Answer : c. Complex Instruction Set Computer
Description : 8253, 8257 c) 8257,8251 d)8251,825721.Consider the following set of 8085 instruction.MVI A,82HORA AJP DSPLYXRA ADSPLY:OUT PORT1HLT.The output at PORT1 isa) 00H b) FFH c) 92H d) 11H
Last Answer : a) 00H
Description : Serial port vector address is of _______. And causes an interrupt when ________. a) 0013H, either TI or RI flag is set b) 0023H, either TI or RI flag is reset c) 0013H, either TI or RI flag is reset d) 0023H, either TI or RI flag is set
Last Answer : a) 0013H, either TI or RI flag is set
Description : Motorola introduced _____ processor: a. 2 bit-RISC b. 4 bit-RISC c. 8 bit-RISC d. 32 bit-RISC
Last Answer : d. 32 bit-RISC
Description : In 8087, _______ many register stack are there? And of _____ registers. These registers are used as _________ stack. a) 7, 40 bit, FIFO. b) 8, 60 bit, LILO. c) 8, 80 bit, LIFO d) 7, 80 bit, FILO.
Last Answer : b) 8, 60 bit, LILO.
Description : What is meant by a dedicated computer? a. which is used by one person only b. which is assigned to one and only one task c. which does one kind of software d. which is meant for application software only
Last Answer : d. which is meant for application software only
Description : What is meant by a dedicated computer? a. Which is used by one person only b. Which is assigned one and only one task c. Which uses one kind of software d. Which is meant for application software
Last Answer : d. Which is meant for application software
Description : A stack is a. an 8-bit register in the microprocessor b. a 16-bit register in the microprocessor c. a set of memory locations in R/WM reserved for storing information temporarily during the execution of computer
Last Answer : c. a set of memory locations in R/WM reserved for storing information temporarily during the execution of computer
Description : Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI
Last Answer : a) IE
Last Answer : d) RI, TI
Description : ____ is the mode we use to execute the instruction from a computer. a) Sequential b) Parallel c) Both (a) & (b) d) None of the above
Last Answer : ____ is the mode we use to execute the instruction from a computer. a) Sequential b) Parallel c) Both (a) & (b) d) None of the above
Description : A set of instruction compiled into a program that perform a particular task is known as: A. Hardware. B.CPU C. Motherboard D. Software
Last Answer : D. Software
Description : Which of the following set of statements reflects the basic characteristics of teaching ? Select the correct alternative from the codes : (i) Teaching is the same as training. (ii) There is no difference between instruction and conditioning ... (vi) (C) (ii), (iii) and (v) (D) (i), (iv) and (vi)
Last Answer : Answer: B
Description : IRET stand for. a. Interrupt enter b. Interrupt return c. Interrupt delete d. None of these
Last Answer : b. Interrupt return
Description : The word processing task associated with changing the appearance of a document is a. Editing b. Writing c. Formatting d. All of above
Last Answer : c. Formatting
Description : In which instruction are used to perform Boolean operation on non-numerical data: a. Logical and bit manipulation b. Shift manipulation c. Circular manipulation d. None of these
Last Answer : a. Logical and bit manipulation
Description : How does the microprocessor differentiate between data and instruction
Last Answer : When the first m/c code of an instruction is fetched and decoded in the instruction register, the microprocessor recognizes the number of bytes required to fetch the entire ... will be considered as data & the byte after the data will be treated as the next instruction.
Description : Why do we use XRA A instruction
Last Answer : The XRA A instruction is used to clear the contents of the Accumulator and store the value 00H.