What is the most common method of testing resistive terminations?

What is the most common method of testing resistive  terminations?
by

1 Answer

Answer :

Reading their resistances with a standard ohmmeter
by

Related questions

If an installed optical fiber cable does not have connectors or terminations on both ends, how should the cable be tested?

Description : If an installed optical fiber cable does not have connectors or terminations on both ends, how should the cable be tested?

Last Answer : With an OTDR unless it is less than 50 meters in length. If it is less than 50 meters in length, continuity should be verified with a flashlight.

What is the most common method of testing a fixed rf attenuator?

Description : What is the most common method of testing a fixed rf attenuator?

Last Answer : Rf substitution method.

The energy dissipated by a resistive load is most often in what form?

Description : The energy dissipated by a resistive load is most often in what form?

Last Answer : Heat.

When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Description : When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Last Answer : . Characteristic impedance.

In cable modem internet access, cable modem terminations system (CMTS) is at: a) cable provider's end b) customer end c) Both of Above d) None of The Above

Description : In cable modem internet access, cable modem terminations system (CMTS) is at: a) cable provider's end b) customer end c) Both of Above d) None of The Above

Last Answer : c) Both of Above

Answer the following S. No Statement Chose the correct answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the blanks 3 Non Contact Infrared Thermometer cannot measure temperature of objects placed in hazardous places True/False 4 To measure the RPM of a Flywheel, ______ type of RPM meter is used and for a visible shaft-end _______ type of RPM meter is used. Fill in the blanks 5 In a switch yard, _____ instrument is used to identify the loose joints and terminations Fill in the blanks 6 Every Designated Consumer shall have its first energy audit conducted by ________ Energy Auditor within ______ months of

Description :  Answer the following S. No Statement Chose the correct  answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the ... of RPM  meter is used and for a visible shaft-end _______ type of  RPM meter is used.

Last Answer : Sr  No Statement Chose the correct  answer OR Fill-in-the-blanks Solution 1 Fyrite measures CO2, O2 and  SO2 True/False False 2 Ultrasonic Flow Meter uses the  principle of____& ____ ... ]  10 In a gasification system the  reduction zone is above the  combustion zone True/False False

Describe the resistive method for liquid level measurement. Write its advantages and disadvantages.

Description : Describe the resistive method for liquid level measurement. Write its advantages and disadvantages.

Last Answer : Working: This method uses mercury as a conductor as shown in the figure. A number of contact rods are placed at various liquid levels. As the level of liquid rises in the tank, head h ... connected in series is calibrated in terms of the liquid level and indicates the liquid level directly. 

What is the most common method of terminating and splicing wires?

Description : What is the most common method of terminating and splicing wires?

Last Answer : The use of preinsulated splices and terminal lugs

The most common method of creating a backup for a microcomputer is what?

Description : The most common method of creating a backup for a microcomputer is what?

Last Answer : Use a floppy disk and the diskcopy procedure.

What is the most common method for erasing a hard disk?

Description : What is the most common method for erasing a hard disk?

Last Answer : Reformat the disk.

What is the power factor in pure resistive , capacitive , inductive load ?

Description : What is the power factor in pure resistive , capacitive , inductive load ?

Last Answer : Answer : Power factor cosΦ = 1 in pure resistive load, cosΦ = 0 in capacitive load , cosΦ = 0 in inductive load .

Which resistive value is comparatively higher ?

Description : Which resistive value is comparatively higher ?

Last Answer : The value of equivalent resistance is greater than any resistance

Figure below shows a block of mass 35 kg resting on a table. The table is so rough that it offers a self adjusting resistive force 10%

Description : Figure below shows a block of mass 35 kg resting on a table. The table is so rough that it offers a self adjusting resistive force 10%

Last Answer : Figure below shows a block of mass 35 kg resting on a table. The table is so rough that it ... so that the block does not slide along the table?

Is computer is Resistive load?

Description : Is computer is Resistive load?

Last Answer : It is resistive much load

Capacitors can be used in electric distribution systems to improve power factor. This is accomplished by seesawing energy between the capacitor and the _____________. A. generator B. inductive loads C. resistive loads D. all of the above

Description : Capacitors can be used in electric distribution systems to improve power factor. This is accomplished by seesawing energy between the capacitor and the _____________. A. generator B. inductive loads C. resistive loads D. all of the above

Last Answer : Answer: B

Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Description : Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Last Answer : Answer: B

Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. C. Inductive reactance varies directly with the frequency and the inductance. D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Description : Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. ... . D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Last Answer : Answer: C

The existing resistance of a conductor is dependent upon its length, cross-sectional area, _____________. A. temperature and insulation B. material and insulation C. resistive coefficient and material D. material and temperature

Description : The existing resistance of a conductor is dependent upon its length, cross-sectional area, _____________. A. temperature and insulation B. material and insulation C. resistive coefficient and material D. material and temperature

Last Answer : Answer: D

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

For an Resistive Load and Inductive load considered for switching operation of circuit breaker, Switching of which load is difficult and Why?

Description : For an Resistive Load and Inductive load considered for switching operation of circuit breaker, Switching of which load is difficult and Why?

Last Answer : In case of switching resistive load, current and voltage will be in phase i.e,when during current zero voltage also will be zero in case of resistive load. Hence the voltage at the ... maximum. This results in re-striking of arc once again. Therefore switching inductive load will be difficult

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

How the starting winding is made resistive?

Description : How the starting winding is made resistive?

Last Answer : It consists of only few turns of smaller diameter.

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Description : What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Last Answer : D. Photovoltaic effect

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ A Damping factor B Damping coefficient C Resistive factor D Resistive coefficient

Description : The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ A Damping factor B Damping coefficient C Resistive factor D Resistive coefficient

Last Answer : A Damping factor

The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ ( A ) Damping factor ( B ) Damping coefficient ( C ) Resistive factor ( D ) Resistive coefficient

Description : The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ ( A ) Damping factor ( B ) Damping coefficient ( C ) Resistive factor ( D ) Resistive coefficient

Last Answer : ( A ) Damping factor

The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ a) Damping factor b) Damping coefficient c) Resistive factor d) Resistive coefficient

Description : The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________ a) Damping factor b) Damping coefficient c) Resistive factor d) Resistive coefficient

Last Answer : a) Damping factor

Pick up the correct statement from the following: (A) High percentage of C3S and low percentage of C2S cause rapid hardening (B) High percentage of C3S and low percentage of C2S make the cement less resistive to chemical attack (C) Low percentage of C3S and high percentage of C2S contribute to slow hardening (D) All the above

Description : Pick up the correct statement from the following: (A) High percentage of C3S and low percentage of C2S cause rapid hardening (B) High percentage of C3S and low percentage of C2S make the cement ... ) Low percentage of C3S and high percentage of C2S contribute to slow hardening (D) All the above

Last Answer : Answer: Option D

A four-arm bridge. All arms of which are predominantly resistive; used for measuring resistance

Description : A four-arm bridge. All arms of which are predominantly resistive; used for measuring resistance

Last Answer : Resistance Bridge and Wheatstone Bridge

It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : It is analogous to power dissipation to copper cables, impurities in the fiber absorb the light and covert it to heat. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : B. absorption loss

Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : A. power loss

A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Description : A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Last Answer : Dummy resistor

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Stress is (a)External force (b)Internal resistive force (c)Axial force (d)Radial force

Description : Stress is (a)External force (b)Internal resistive force (c)Axial force (d)Radial forcee

Last Answer : (b)Internal resistive force

Single-phase Midpoint controlled rectifier with Resistive load

Description : Single-phase Midpoint controlled rectifier with Resistive load

Last Answer : Single-phase Midpoint controlled rectifier with Resistive load:  1) During positive half cycle of AC supply, a is positive with respect to b , this makes T1 forward biased and T2 is reverse ... voltage reverses the polarity and T2 is turned off. The operation is as shown in waveforms.

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Description : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Last Answer : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be 4.

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

The core flux of a practical transformer with a resistive load

Description : The core flux of a practical transformer with a resistive load  A) Is strictly constant with load changes B) Increases linearly with load C) Increases as the square root of the load D) Decrease with increased load

Last Answer : The core flux of a practical transformer with a resistive load Is strictly constant with load changes

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the

Description : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and ... reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

Last Answer : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is 2.24A

In a pure resistive circuit, the average power Pavg is _________ the peak power Pmax.

Description : In a pure resistive circuit, the average power Pavg is ______ the peak power Pmax. (1) Double (2) One-half of (3) One-fourth (4) Equal to

Last Answer : In a pure resistive circuit, the average power Pavg is One-half of the peak power Pmax.

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge

Description : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is :  (A) 2.8 (B) 2.6 (C) 4.6 (D) 3.6

Last Answer : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is : 4.6

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

A 10 bit resistive divider is constructed such that the current through...

Description : A 10 bit resistive divider is constructed such that the current through the LSB resistor is 100μA. The maximum current that will flow through the MSB resistor is 

Last Answer : A 10 bit resistive divider is constructed such that the current through the LSB resistor is 100μA. The maximum current that will flow through the MSB resistor is 51.2mA.

A single-phase transmission line of impedance j 0.8 ohm supplies a resistive...

Description :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

Last Answer :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is 0.6 lagging.

At ______ frequencies the parallel R-L circuit behaves as purely resistive.

Description : At ______ frequencies the parallel R-L circuit behaves as purely resistive.

Last Answer : At very high frequencies the parallel R-L circuit behaves as purely resistive.