Description : . What percent of regulation would be ideal?
Last Answer : 0%.
Description : 62)The no-load current drawn by transformer is usually........percent of the full-load current? A. 0.2 to 0.5 % B. 2 to 5% C. 12 to 15 % D. 20 to 30 %
Last Answer : B) 2 to 5%
Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?
Last Answer : 240 volts.
Description : What is the power consumed by 'R3' in the circuit illustrated if the supply is 24 volts and resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 12 watts B. 20 watts C. 24 watts D. 48 watts
Last Answer : Answer: B
Description : What is the power consumed by 'R2' in the circuit illustrated, if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 16 watts B. 20 watts C. 24 watts D. 28 watts
Last Answer : Answer: A
Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts
Last Answer : Answer: D
Description : A compound generator has a no-load voltage of 250 volts and a full-load voltage of 230 volts, and therefore, is considered to be _____________. A. flat compounded B. over compounded C. under compounded D. terminal compounded
Last Answer : Answer: C
Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #
Description : Load regulation is a measure of a power supplies ability keep a constant output under conditions of changing A) Line voltage B) Current demand C) Temperature D) Oscillator frequency.
Last Answer : A) Line voltage
Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?
Last Answer : 63.7 volts.
Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?
Last Answer : 63.6 volts.
Description : A two-winding single phase transformer has a voltage regulation of 4.5% at full-load and unity power-factor. At full-load and 0.80 power-factor lagging load the voltage regulation will be (A) 4.5%. (B) less than 4.5%. (C) more than 4.5%. (D) 4.5% or more than 4.5%.
Last Answer : (C) more than 4.5%.
Description : A two -winding single phase transformer has a voltage regulation of 4.5% at full - load and unity power -factor. At full -load and 0.80 lagging power-factor, the voltage regulation will be: (A) 4.5% (B) less than 4.5% (C) more than 4.5% (D) none of the above
Last Answer : A two -winding single phase transformer has a voltage regulation of 4.5% at full - load and unity power -factor. At full -load and 0.80 lagging power-factor, the voltage regulation will be: more than 4.5%
Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : What is the power consumed by 'R1' in the circuit illustrated if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 watts B. 3 watts C. 6 watts D. 12 watts
Description : What is the total power consumed by the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 watts B. 12 watts C. 48 watts D. 288 watts
Description : What term applies to the use of two or more generators to supply a common load?
Last Answer : Parallel operation.
Description : If the load requirement consists of both positive and negative voltages, what technique is used in the voltage divider to supply the loads from a single voltage source?
Last Answer : The ground (reference point) is placed in the proper point in the voltage divider so that positive and negative voltages are supplied
Description : A resistor placed in parallel to the output of a power supply _____________. A. is a temperature compensator B. corrects power factor C. prevents excessive currents D. aids in output voltage regulation
Description : A commercial power supply has a voltage regulation of: 1. 1% 2.5% 3.20% 4.50%
Last Answer : A commercial power supply has a voltage regulation of: 1%
Description : Voltage can be stepped up from 6 to approximately a) 10,000 volts b) 15.00 0 volts c) 20,000 volts d) 25,000 volts
Last Answer : c) 20,000 volts
Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw
Description : What type of bias (positive or negative) is added to a negative damper for the most positive extremity of the wave shape to be clamped above 0 volts?
Last Answer : Positive bias.
Description : A negative damper damps which extremity of the output waveshape to 0 volts?
Last Answer : Most positive.
Description : A positive damper clamps which extremity of the output signal to 0 volts?
Last Answer : Most negative.
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : What precaution should you take when you use 115 volts to zero a differential?
Last Answer : Never leave the circuit energized for more than 2 minutes.
Description : Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?
Last Answer : Zener effect.
Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage
Last Answer : 15.9 volts.
Description : What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?
Last Answer : There is no effect
Description : Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.
Last Answer : (a) 250 kV, (b) 25 V, (c) 1µV
Description : Convert 2.1 kV to volts.
Last Answer : 2100 volts.
Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?
Last Answer : 340 volts.
Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?
Last Answer : 42.
Description : If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?
Last Answer : 495 mA.
Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?
Last Answer : 50 volts.
Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?
Last Answer : 1.25 amperes.
Description : If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?
Last Answer : 43.3 ohms.
Description : If the alternating source in Q41 is changed to 200 volts peak-to-peak, what is Iavg?
Last Answer : Iavg = 0.636 × Imax = 1.41 amperes.
Description : a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?
Last Answer : a. It is the maximum voltage the capacitor can work without risk of damage. b. 900 volts.
Description : A transformer has negative voltage regulation when its load power factor is- (a) Zero (b) Unity (c) Leading (d) Lagging
Last Answer : Ans: C
Description : 51 A transformer has negative voltage regulation when its load power factor is A. Zero B. Unity C. Leading D. Lagging
Last Answer : C. leading
Description : For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is
Last Answer : For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is 0.707 lead
Description : A transformer has negative voltage regulation when its load power factor is (1) Zero (2) Unity (3) Leading (4) Lagging
Last Answer : 0
Description : Minimum voltage regulation occurs when the power factor of the load is?
Last Answer : Minimum voltage regulation occurs when the power factor of the load is leading.
Description : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is
Last Answer : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is 20 V
Description : The dc motor, which can provide zero speed regulation at full load without any controller is (A) series (B) shunt (C) cumulative compound (D) differential compound
Last Answer : The dc motor, which can provide zero speed regulation at full load without any controller is shunt
Description : In a transformer, zero voltage regulation at full load is (a)Not possible (b) Possible at unity power factor load (c) Possible at leading power factor load (d) Possible at lagging power factor load
Last Answer : In a transformer, zero voltage regulation at full load is Possible at leading power factor load