Waveforms are described in terms of what two functions?

Waveforms are described in terms of what two functions?
by

1 Answer

Answer :

Amplitude and time.
by

Related questions

Waveforms are described in terms of what two functions?

Description : Waveforms are described in terms of what two functions?

Last Answer : Amplitude and time.

Name two instruments used to analyze waveforms.

Description : Name two instruments used to analyze waveforms.

Last Answer : Oscilloscope and spectrum analyzer.

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.

which waveforms on the left have a resultant wave of zero, and what is indicated by these waves?

Description : which waveforms on the left have a resultant wave of zero, and what is indicated by these waves?

Last Answer : 2 and 6 have zero resultant wave and they indicate that the incident and reflected waves are 180 degrees out of phase at all parts.

The waveforms shown below are the input and output of an overdrive

Description : The waveforms shown below are the input and output of an overdrive

Last Answer : a. Cutoff. b. Saturation.

What waveform is the basis of all complex waveforms?

Description : What waveform is the basis of all complex waveforms?

Last Answer : The sine wave.

Name two of the three described uses of a two-wire open line.

Description : Name two of the three described uses of a two-wire open line.

Last Answer : Power lines, rural telephone lines, and telegraph lines

If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts

What is the voltage dropped by each resistor of the circuit described in question 17?

Description : What is the voltage dropped by each resistor of the circuit described in question 17?

Last Answer : E1 = 60 volts. E2 = 180 volts. E3 = 240 volts.

What type of resistor should be used in the circuit described in question 12?

Description : What type of resistor should be used in the circuit described in question 12?

Last Answer : A wirewound resistor.

Positive control of induction is best described as a control system in which an operon functions (A) Unless it is switched off by a derepressed repressor protein (B) Only after a repressor protein is inactivated by an inducer (C) Only after an inducer protein, which can be inactivated by a corepressor, switches it on (D) Only after an inducer protein, which is activated by an inducer, switch it on

Description : Positive control of induction is best described as a control system in which an operon functions (A) Unless it is switched off by a derepressed repressor protein (B) Only after a repressor protein is ... on (D) Only after an inducer protein, which is activated by an inducer, switch it on

Last Answer : Answer : D

Find the area of a right angled triangle with sides of 90 degree unit and the functions described by L = cos y and M = sin x. a) 0 b) 45 c) 90 d) 180

Description : Find the area of a right angled triangle with sides of 90 degree unit and the functions described by L = cos y and M = sin x. a) 0 b) 45 c) 90 d) 180

Last Answer : d) 180

A segment is any object described by GKS commands and data that start with CREATE SEGMENT and Terminates with CLOSE SEGMENT command. What functions can be performed on these segments? (1) Translation and Rotation (2) Panning and Zooming (3) Scaling and Shearing (4) Translation, Rotation, Panning and Zooming

Description : A segment is any object described by GKS commands and data that start with CREATE SEGMENT and Terminates with CLOSE SEGMENT command. What functions can be performed on these segments? (1) Translation ... 2) Panning and Zooming (3) Scaling and Shearing (4) Translation, Rotation, Panning and Zooming

Last Answer : Translation, Rotation, Panning and Zooming

In a two -channel oscilloscope operating in x -y mode, two in -phase 50 Hz sinusoidal waveforms of equal ...

Description : In a two -channel oscilloscope operating in x -y mode, two in -phase 50 Hz sinusoidal waveforms of equal amplitude are fed to the two channels. What will be the resultant pattern on the screen ? (a) An ellipse (b) A parabola (c) Straight line inclined at 45° with respect to x-axis (d) A circle

Last Answer : In a two -channel oscilloscope operating in x -y mode, two in -phase 50 Hz sinusoidal waveforms of equal amplitude are fed to the two channels. What will be the resultant pattern on the screen ? (a) An ellipse (b) A parabola (c) Straight line inclined at 45° with respect to x-axis (d) A circle

Ammeters and voltmeters used in sinusoidal AC power systems indicate which of the following values of the waveforms measured? A. Peak value B. Root-mean-square value C. Average value D. Maximum value

Description : Ammeters and voltmeters used in sinusoidal AC power systems indicate which of the following values of the waveforms measured? A. Peak value B. Root-mean-square value C. Average value D. Maximum value

Last Answer : Answer: B

An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Description : An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Last Answer : B. Phonoscope

Which of the following ECG waveforms characterizes conduction of an electrical impulse through the left ventricle? a) QRS complex The QRS complex represents ventricular depolarization b) P wave The P wave is an ECG characteristic reflecting conduction of an electrical impulse through the atria. c) PR interval The PR interval is a component of an ECG tracing reflecting conduction of an electrical impulse through the AV node. d) QT interval The QT interval is an ECG characteristic reflecting the time from ventricular depolarization to repolarization.

Description : Which of the following ECG waveforms characterizes conduction of an electrical impulse through the left ventricle? a) QRS complex The QRS complex represents ventricular depolarization b) P ... QT interval is an ECG characteristic reflecting the time from ventricular depolarization to repolarization.

Last Answer : a) QRS complex The QRS complex represents ventricular depolarization

What are the different tones used in strowger telephony? Explain with the help of waveforms and the timings.

Description : What are the different tones used in strowger telephony? Explain with the help of waveforms and the timings.

Last Answer : Dial Tone: This tone is used to indicate that the exchange is ready to accept dialed digits from the subscriber. The subscriber should start dialing only after hearing the dialing tone. Sometimes, ... as the call progresses through different exchanges. Fig. shows a routing tone pattern.   

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

With the help of waveforms and phasor diagrams, show the phase relationship between voltage and current in pure inductive circuit.

Description : With the help of waveforms and phasor diagrams, show the phase relationship between voltage and current in pure inductive circuit.

Last Answer : Phasor Diagram:  

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Draw and explain the working of combinational Clipper with waveforms.

Description : Draw and explain the working of combinational Clipper with waveforms.

Last Answer : Explanation:- As shown in figure the combinational clipper is the combination of positive biased and negative biased clipper. The combinational clipper can be used to clip both two independent ... open circuit. Hence the value of output voltage cannot exceed the voltage level of VB2. 

With the help of circuit diagram and waveforms, explain working of RC differentiator.

Description : With the help of circuit diagram and waveforms, explain working of RC differentiator.

Last Answer : Fig: RC differentiating circuit Figure shows a RC differential circuit. It is also known as high pass filter. The reactance of a capacitor decreases with increasing frequency. The higher ... i.e. the output signal is directly proportional to the derivative of the input signal.  

Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram:    

Draw & describe working of bridge rectifier with its input output waveforms

Description : Draw & describe working of bridge rectifier with its input output waveforms

Last Answer : Four diodes are used. a)In positive half cycle Diodes D1 & D3 becomes forward biased they will conduct & current flows at that time D2 and D4 are reverse biased they will not ... at that time D1 and D3 are reverse biased they will not conduct. we get full cycle rectification.

Draw and describe working of series biased clipper with input output waveforms.

Description : Draw and describe working of series biased clipper with input output waveforms. 

Last Answer : Biased series positive clipper: Clipping of the signal takes place as soon as the input signal goes positive. If we want to change/adjust the clipping level of AC voltage, then external biasing voltage must be ... voltage must be used. The figure given below shows a biased (series) clipper.    

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Define PAM, PWM, and PPM. Draw waveforms.

Description : Define PAM, PWM, and PPM. Draw waveforms.

Last Answer : Pulse amplitude modulation is defined as a process of varying the amplitude of the carrier pulse in accordance to the modulating signal variations. Pulse width modulation is defined as a ... of varying the position of the carrier pulse, in accordance to the modulating signal variations.

Explain effect of 'm' on AM with neat waveforms.

Description : Explain effect of 'm' on AM with neat waveforms.

Last Answer : i)m< 1  If m < 1 or if the percentage of modulation is less than 100% the this type of modulation is known as under modulation The amplitude of modulating signal less than carrier ... greater amplitude part of its information is lost in the process of modulation which is undesirable.

Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Last Answer : block diagram of FM super heterodyne radio receiver

Explain the working of MTI radar with the help of block diagram and with suitable waveforms.

Description : Explain the working of MTI radar with the help of block diagram and with suitable waveforms.

Last Answer : Explanation : The echo pulse from the target is received by MTI radar antenna. If echo is due to moving target, the echo pulse undergoes a Doppler frequency. The received echo pulses then pass ... for fixed target magnitude and polarity of output will remain the same as shown in figure.

Explain fast frequency hopping techniques with suitable waveforms. State its advantage and disadvantages.

Description : Explain fast frequency hopping techniques with suitable waveforms. State its advantage and disadvantages. 

Last Answer : In Fast Frequency hopping multiple frequencies or hops are used to transmit one symbol. The hop rate is higher than symbol rate but chip rate is equal to hop rate For each symbol ... at receiver 3. Complex and expensive digital frequency synthesizers are required 4. Data rates are low

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Draw circuit diagram for π filter and explain its working with waveforms.

Description : Draw circuit diagram for π filter and explain its working with waveforms.

Last Answer : Working of a Pi filter: In this circuit, we have a capacitor in parallel, then an inductor in series, followed by another capacitor in parallel. Capacitor C1 − This filter capacitor ... any ac component present in the signal to pass through it, which the inductor has failed to block.

Explain stagger tuned amplifier with the help of waveforms.

Description : Explain stagger tuned amplifier with the help of waveforms.

Last Answer : Circuit Diagram: Above figure shows two-stage tuned voltage amplifier. The stagger tuning in this circuit, may be achieved by resonating the tuned circuits L1C1 and L2C2 to slightly different ... outside the pass-band. Because of the stagger tuning there is a loss of voltage gain.

Classify the power amplifiers on the basis of operation and input/output waveforms.

Description : Classify the power amplifiers on the basis of operation and input/output waveforms.

Last Answer : Depending upon the operation and input/output waveforms power amplifiers are classified into following type. 1) Class A amplifier. 2) Class B amplifier. 3) Class C amplifier. 4) Class AB amplifier. 5) Class D amplifier

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Description : For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Last Answer : Class D commutation: This is also called as auxiliary commutation because it uses an auxiliary SCR to switch the charged capacitor across conducting SCR to turn it off. In this scheme, the main ... make SCR1 forward biased and keep ready for next triggering. The above cyclic process is repeated.

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

State different types of electrical signal and draw all types of waveforms.

Description : State different types of electrical signal and draw all types of waveforms.

Last Answer : Types of electrical signals 1) Sine wave 2) Triangular wave 3) Square wave Waveforms

i) State the significance of modulation index in AM transmission. ii) Explain the effect of modulation index on AM wave with waveforms.

Description : i) State the significance of modulation index in AM transmission. ii) Explain the effect of modulation index on AM wave with waveforms.

Last Answer : Significance of modulation index in AM transmission  It is used to determine the strength and quality of transmitted signal. If the modulation index is small, then the amount of variation in ... amplitude part of its information is lost in the process of modulation which is undesirable.

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

What is Phase sequence? Draw waveforms of 3 phase emf.

Description : What is Phase sequence? Draw waveforms of 3 phase emf.

Last Answer : Phase sequence: It is the order in which the three phases reach their peak or maximum values. It is shown in below fig. the phase sequence is A-B-C (or R-Y-B). In the following waveforms, it is ... 120º, B- phase voltage attains its positive maximum value. So the phase sequence is R-Y-B. 

Define phase sequence of three phase supply with waveforms.

Description : Define phase sequence of three phase supply with waveforms. What is normal phase sequence? Which 3 standard colours are used to denote the phase sequence?

Last Answer : It  is  sunnosoidal  sequence.

In which of the following waveforms is RMS voltage equal to the average voltage?

Description : In which of the following waveforms is RMS voltage equal to the average voltage? A) Triangle wave B) Square wave C) Sine wave D) None of these

Last Answer : In which of the following waveforms is RMS voltage equal to the average voltage? A) Triangle wave B) Square wave C) Sine wave D) None of these

Which of the following waveforms has the lowest form factor?

Description : Which of the following waveforms has the lowest form factor? A) Sine wave B) Square wave C) Sawtooth wave D) Triangle wave

Last Answer : Which of the following waveforms has the lowest form factor? A) Sine wave B) Square wave C) Sawtooth wave D) Triangle wave

Explain the principle of ON OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Description : Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Last Answer : The integral cycle control (on-off control) and phase angle control are the two types of AC voltage controller. The principle of ON-OFF control: The on-off control is also called an integral cycle ... control. In phase control, the switch is on for some period of each cycle.  

The rotational effect of a force on a body about an axis of rotation is described in terms of the (1) Centre of gravity (2) Centripetal force (3) Centrifugal force (4) Moment of force

Description : The rotational effect of a force on a body about an axis of rotation is described in terms of the (1) Centre of gravity (2) Centripetal force (3) Centrifugal force (4) Moment of force

Last Answer : (4) Moment of force Explanation: The rotational effect of a force on a body about an axis of rotation is described in terms of the Moment of force.