An ideal power supply consist of

An ideal power supply consist of 

 (A) Very small output resistance (B) Zero Internal resistance (C) Very large input resistance (D) Very large output resistance
by

1 Answer

Answer :

An ideal power supply consist of Zero Internal resistance 

by

Related questions

A substance whose molecules consist of dissimilar atoms is called?

Description : A substance whose molecules consist of dissimilar atoms is called?

Last Answer : A substance whose molecules consist of dissimilar atoms is called compound.

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

When current flows through heater coil it glows but supply wiring does not glow because?

Description : When current flows through heater coil it glows but supply wiring does not glow because?

Last Answer : When current flows through heater coil it glows but supply wiring does not glow because resistance of heater coil is more than the supply wires.

What does your (regular) breakfast consist of, what is your ideal fantasy breakfast - and what is a healthy breakfast, in your opinion?

Description : What does your (regular) breakfast consist of, what is your ideal fantasy breakfast - and what is a healthy breakfast, in your opinion?

Last Answer : answer:Hm, personally my stomach couldn't handle that right off the bat. The yogurts mixing with the acids of the citrus just wouldn't bode over for me, the banana is great but then the coffee being hot ... off we tend to eat out, its crazy. I think I should just stick to Grape Nuts and berries.

In order to get maximum power transfer from a capacitive source, the load must?

Description : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

Last Answer : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

If it takes 400 ms to use 12,000 J of energy, the power is?

Description : If it takes 400 ms to use 12,000 J of energy, the power is? A.30 kW B.30 W C.3 W D.300 kW

Last Answer : If it takes 400 ms to use 12,000 J of energy, the power is? A.30 kW B.30 W C.3 W D.300 kW

A constant load power means a uniform conversion of?

Description : A constant load power means a uniform conversion of? A.mechanical to electrical energy B.electrical to mechanical energy C.current to voltage D.voltage to current

Last Answer : A constant load power means a uniform conversion of? A.mechanical to electrical energy B.electrical to mechanical energy C.current to voltage D.voltage to current

If you used 600 W of power for 60 h, you have used?

Description : If you used 600 W of power for 60 h, you have used? A.36 kWh B.3.6 kWh C.10 kWh D.1 kWh

Last Answer : If you used 600 W of power for 60 h, you have used? A.36 kWh B.3.6 kWh C.10 kWh D.1 kWh

Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

Description : Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

Last Answer : Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open the other two bulbs will light.

Chandigarh is a city which has roads generally parallel or perpendicular to each other. The ideal water supply system in such a city should be a. Dead and system b. Grid Iron system* c. Ring system d. Any of them

Description : Chandigarh is a city which has roads generally parallel or perpendicular to each other. The ideal water supply system in such a city should be a. Dead and system b. Grid Iron system* c. Ring system d. Any of them

Last Answer : b. Grid Iron system*

A power tiller consist of the following main components a) Engine c) Transmission gear b) Clutch d) All of the above

Description : A power tiller consist of the following main components a) Engine c) Transmission gear b) Clutch d) All of the above

Last Answer : All of the above

Inductance

Description : Inductance

Last Answer : Inductance

Resistance

Description : Resistance

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

For one ac cycles .. alternator needs to rotate??

Description : please answer

Last Answer : 360 degree . 180 Degree Positive and 180 degree negative

When a sine wave has a frequency of 100 Hz in 12 s it goes through?

Description : When a sine wave has a frequency of 100 Hz in 12 s it goes through? A.1/100 cycle B.12 cycles C.120 cycles D.1,200 cycles

Last Answer : When a sine wave has a frequency of 100 Hz in 12 s it goes through? A.1/100 cycle B.12 cycles C.120 cycles D.1,200 cycles

Fourteen milliamperes can be expressed as?

Description : Fourteen milliamperes can be expressed as? A.14 MA B.14 μA C.14 kA D.14 mA

Last Answer : Fourteen milliamperes can be expressed as? A.14 MA B.14 μA C.14 kA D.14 mA

How much voltage is needed to produce 2.5 A of current through a 200 ohms resistor?

Description : How much voltage is needed to produce 2.5 A of current through a 200 ohms resistor? A.50 V B.500 V C.80 V D.8 V

Last Answer : 500 V

When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is?

Description : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

Last Answer : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

How much resistance is needed to draw 17.6 mA from a 12 volt source?

Description : How much resistance is needed to draw 17.6 mA from a 12 volt source? A.212 ohms B.6.8 kohms C.68 ohms D.680 ohms

Last Answer : How much resistance is needed to draw 17.6 mA from a 12 volt source? A.212 ohms B.6.8 kohms C.68 ohms D.680 ohms

When placed close together, two positively charged materials will?

Description : When placed close together, two positively charged materials will? A.attract B.become neutral C.become negative D.repel

Last Answer : When placed close together, two positively charged materials will? A.attract B.become neutral C.become negative D.repel

The colored bands for a 4,700 ohm resistor with a ten percent tolerance are?

Description : The colored bands for a 4,700 ohm resistor with a ten percent tolerance are? A.yellow, violet, red, gold B.yellow, violet, orange, gold C.yellow, violet, red, silver D.orange, violet, red, silver

Last Answer : The colored bands for a 4,700 ohm resistor with a ten percent tolerance are? A.yellow, violet, red, gold B.yellow, violet, orange, gold C.yellow, violet, red, silver D.orange, violet, red, silver

A certain appliance uses 350 W. If it is allowed to run continuously for 24 days, how many kilowatt- hours of

Description : A certain appliance uses 350 W. If it is allowed to run continuously for 24 days, how many kilowatt- hours of energy does it consume? A.20.16 kWh B.201.6 kWh C.2.01 kWh D.8.4 kWh

Last Answer : A certain appliance uses 350 W. If it is allowed to run continuously for 24 days, how many kilowatt- hours of energy does it consume? A.20.16 kWh B.201.6 kWh C.2.01 kWh D.8.4 kWh

When the turns ratio of a transformer is 20 and the primary ac voltage is 12 V, the secondary voltage is?

Description : When the turns ratio of a transformer is 20 and the primary ac voltage is 12 V, the secondary voltage is? A.12 V B.120 V C.240 V D.2,400 V

Last Answer : When the turns ratio of a transformer is 20 and the primary ac voltage is 12 V, the secondary voltage is? A.12 V B.120 V C.240 V D.2,400 V

In a certain loaded transformer, the secondary voltage is one-fourth the primary voltage. The secondary

Description : In a certain loaded transformer, the secondary voltage is one-fourth the primary voltage. The secondary current is? A.one-fourth the primary current B.four times the primary current C.equal to the primary current D.one-fourth the primary current and equal to the primary current

Last Answer : In a certain loaded transformer, the secondary voltage is one-fourth the primary voltage. The secondary current is? A.one-fourth the primary current B.four times the primary current C.equal to the primary current D.one-fourth the primary current and equal to the primary current

In a Y-connected circuit, the magnitude of each line current is?

Description : In a Y-connected circuit, the magnitude of each line current is? A.one-third the phase current B.three times the corresponding phase current C.equal to the corresponding phase current D.zero

Last Answer : In a Y-connected circuit, the magnitude of each line current is? A.one-third the phase current B.three times the corresponding phase current C.equal to the corresponding phase current D.zero

The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330

Description : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

Last Answer : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

The turns ratio required to match an 80 ohms source to a 320 ohms load is?

Description : The turns ratio required to match an 80 ohms source to a 320 ohms load is? A.80 B.20 C.4 D.2

Last Answer : c

When the pointer of an analog ohmmeter reads close to zero, the resistor being measured is?

Description : When the pointer of an analog ohmmeter reads close to zero, the resistor being measured is? A.overheated B.shorted C.open D.reversed

Last Answer : When the pointer of an analog ohmmeter reads close to zero, the resistor being measured is? A.overheated B.shorted C.open D.reversed

A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately?

Description : A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately? A.15.1 μA B.151 μA C.66 mA D.660 mA

Last Answer : A

The formula to find I when the values of V and R are known is?

Description : The formula to find I when the values of V and R are known is? A.I = VR B.I = R/V C.V = IR D.I = V/R

Last Answer : The formula to find I when the values of V and R are known is? A.I = VR B.I = R/V C.V = IR D.I = V/R

When converting 0.16 mA to microamperes, the result is?

Description : When converting 0.16 mA to microamperes, the result is? A.16 μA B.160 μA C.1,600 μA D.0.0016 μA

Last Answer : When converting 0.16 mA to microamperes, the result is? A.16 μA B.160 μA C.1,600 μA D.0.0016 μA

The average value of a 12 V peak sine wave over one complete cycle is?

Description : The average value of a 12 V peak sine wave over one complete cycle is? A.0 V B.1.27 V C.7.64 V D.6.37 V

Last Answer : The average value of a 12 V peak sine wave over one complete cycle is? A.0 V B.1.27 V C.7.64 V D.6.37 V

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

A certain transformer has 400 turns in the primary winding and 2,000 turns in the secondary

Description : A certain transformer has 400 turns in the primary winding and 2,000 turns in the secondary winding. The turns ratio is? A.0.2 B.0.4 C.5 D.25

Last Answer : A certain transformer has 400 turns in the primary winding and 2,000 turns in the secondary winding. The turns ratio is? A.0.2 B.0.4 C.5 D.25

A material that does not allow current under normal conditions is a(n)?

Description : A material that does not allow current under normal conditions is a(n)? A.insulator B.conductor C.semiconductor D.valence

Last Answer : A material that does not allow current under normal conditions is a(n)? A.insulator B.conductor C.semiconductor D.valence

Current flows in a circuit when?

Description : Current flows in a circuit when? A.a switch is opened B.a switch is closed C.the switch is either open or closed D.there is no voltage

Last Answer : Current flows in a circuit when? A.a switch is opened B.a switch is closed C.the switch is either open or closed D.there is no voltage

Four amperes of current are measured through a 24 ohms resistor connected across a voltage

Description : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

Last Answer : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

You are measuring the current in a circuit that is operated on an 18 V battery. The ammeter

Description : You are measuring the current in a circuit that is operated on an 18 V battery. The ammeter reads 40 mA. Later you notice the current has dropped to 20 mA. How much has the voltage changed? A.9 V B.900 mV C.0 V D.18 V

Last Answer : You are measuring the current in a circuit that is operated on an 18 V battery. The ammeter reads 40 mA. Later you notice the current has dropped to 20 mA. How much has the voltage changed? A.9 V B.900 mV C.0 V D.18 V

How much resistance is required to limit the current from a 12 V battery to 3.6 mA?

Description : How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

Last Answer : How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

The number of millivolts in 0.06 kilovolts is?

Description : The number of millivolts in 0.06 kilovolts is? A.600 V B.6,000 mV C.60,000 mV D.600,000 mV

Last Answer : The number of millivolts in 0.06 kilovolts is? A.600 V B.6,000 mV C.60,000 mV D.600,000 mV

A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of?

Description : A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of? B.12 kHz C.18 kHz D.1.3 MHz

Last Answer : A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of? B.12 kHz C.18 kHz D.1.3 MHz

If a transformer has 50 turns in the primary winding and 10 turns in the secondary winding,

Description : If a transformer has 50 turns in the primary winding and 10 turns in the secondary winding, what is the reflective resistance if the secondary load resistance is 250 ohms? A.250 ohms B.25 ohms C.6,250 ohms D.62,500 ohms

Last Answer : 6,250 ohms

How many watt-hours represent 65 W used for 18 h?

Description : How many watt-hours represent 65 W used for 18 h? A.11.7 Wh B.1,170 Wh C.11,700 Wh D.117,000 Wh

Last Answer : How many watt-hours represent 65 W used for 18 h? A.11.7 Wh B.1,170 Wh C.11,700 Wh D.117,000 Wh

In 0.025 W, there are?

Description : In 0.025 W, there are? A.25 kW B.0.00025 mW C.2,500 μW D.25 mW

Last Answer : In 0.025 W, there are? A.25 kW B.0.00025 mW C.2,500 μW D.25 mW

A two-terminal variable resistor is known as a?

Description : A two-terminal variable resistor is known as a? A.potentiometer B.thermistor C.rheostat D.wiper

Last Answer : A two-terminal variable resistor is known as a? A.potentiometer B.thermistor C.rheostat D.wiper

The minimum resistance value for a blue, gray, red, silver resistor is?

Description : The minimum resistance value for a blue, gray, red, silver resistor is? A.612 ohms B.6,120 ohms C.6,800 ohms D.6,460 ohms

Last Answer : The minimum resistance value for a blue, gray, red, silver resistor is? A.612 ohms B.6,120 ohms C.6,800 ohms D.6,460 ohms

Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of

Description : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms

Last Answer : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms

Approximately how many milliamperes of current flow through a circuit with a 40 V source and

Description : Approximately how many milliamperes of current flow through a circuit with a 40 V source and 6.8 k ohms of resistance? A.27.2 mA B.59 mA C.5.9 mA D.590 mA

Last Answer : Approximately how many milliamperes of current flow through a circuit with a 40 V source and 6.8 k ohms of resistance? A.27.2 mA B.59 mA C.5.9 mA D.590 mA

When converting 7,000 nA to microamperes, the result is?

Description : When converting 7,000 nA to microamperes, the result is? A.0.007 μA B.0.7 μA C.700 μA D.7 μA

Last Answer : When converting 7,000 nA to microamperes, the result is? A.0.007 μA B.0.7 μA C.700 μA D.7 μA

If the peak value of a sine wave is 30 V, the rms value is?

Description : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

Last Answer : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V