A rail which is tapered to a toe at one end and has a heel at the other end is called as : a) Stock rail b) Tongue rail c) Wing rail d) Lead rail

A rail which is tapered to a toe at one end and has a heel at the other end is called as :
 a) Stock rail b) Tongue rail c) Wing rail d) Lead rail
by

1 Answer

Answer :

b) Tongue rail
by

Related questions

Minimum clearance between toe of Open switch and stock rail for new works a. 115 mm* b. 120 mm c. 95 mm d. 110 mm

Description : Minimum clearance between toe of Open switch and stock rail for new works a. 115 mm* b. 120 mm c. 95 mm d. 110 mm

Last Answer : a. 115 mm*

The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Description : The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Last Answer : Answer: Option A

Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is provided at the bottom of the slab (C) In the heel slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Description : Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is ... slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Last Answer : Answer: Option D

When the reservoir is full, the maximum compressive force in a gravity dam is produced (A) At the toe (B) At the heel (C) Within the middle third of base (D) At centre of base

Description : When the reservoir is full, the maximum compressive force in a gravity dam is produced (A) At the toe (B) At the heel (C) Within the middle third of base (D) At centre of base

Last Answer : Answer: Option A

The uplift pressure on the face of a drainage gallery in a dam is taken as (A) Hydrostatic pressure at toe (B) Average of hydrostatic pressure at toe and heel (C) Two-third of hydrostatic pressure at toe plus one-third of hydrostatic pressure at heel (D) None of the above

Description : The uplift pressure on the face of a drainage gallery in a dam is taken as (A) Hydrostatic pressure at toe (B) Average of hydrostatic pressure at toe and heel (C) Two-third of hydrostatic pressure at toe plus one-third of hydrostatic pressure at heel (D) None of the above

Last Answer : Answer: Option C

i have narrow heel with regular in toe where can i find shoe store that carries such shoes.?

Description : i have narrow heel with regular in toe where can i find shoe store that carries such shoes.?

Last Answer : where can i find shoes with b width in base but need narrower heel

The low temperature reservoir of the heat reservoirs is known as ______.  A. Source reservoir  B. Heel reservoir  C. Toe reservoir  D. Sink reservoir

Description : The low temperature reservoir of the heat reservoirs is known as ______.  A. Source reservoir  B. Heel reservoir  C. Toe reservoir  D. Sink reservoir

Last Answer : Sink reservoir

.Minimum wing rail clearance opposing nose of crossing on Fan shaped turnout a. 45 mm b. 40 mm c. 41 mm* d. 44 mm

Description : .Minimum wing rail clearance opposing nose of crossing on Fan shaped turnout a. 45 mm b. 40 mm c. 41 mm* d. 44 mm

Last Answer : c. 41 mm*

In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as (A) A key (B) A cut-off wall (C) A rib (D) All the above

Description : In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as (A) A key (B) A cut-off wall (C) A rib (D) All the above

Last Answer : Answer: Option D

They experimented with light transmission cables through bundle of fibers and lead to the development of flexible fiberscope. ∙ A. Townes, Schawlow and Kao ∙ B. Maiman, Kao and Bockham ∙ C. Maurer, Kapron and Keck ∙ D. Van Heel, Hopkins and Kapany

Description : They experimented with light transmission cables through bundle of fibers and lead to the development of flexible fiberscope. ∙ A. Townes, Schawlow and Kao ∙ B. Maiman, Kao and Bockham ∙ C. Maurer, Kapron and Keck ∙ D. Van Heel, Hopkins and Kapany

Last Answer : D. Van Heel, Hopkins and Kapany

Coulomb's wedge theory assumes that (A) Back fill is dry, cohesionless, homogeneous and isotropic (B) Slip surface is the plane which passes through the heel of the wall (C) Position and direction of the resultant earth pressure are known (D) All the above

Description : Coulomb's wedge theory assumes that (A) Back fill is dry, cohesionless, homogeneous and isotropic (B) Slip surface is the plane which passes through the heel of the wall (C) Position and direction of the resultant earth pressure are known (D) All the above

Last Answer : (D) All the above

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

The design of heel slab of a retaining wall is based on the maximum bending moment due to: (A) Its own weight (B) Weight of the soil above it (C) Load of the surcharge, if any (D) All the above

Description : The design of heel slab of a retaining wall is based on the maximum bending moment due to: (A) Its own weight (B) Weight of the soil above it (C) Load of the surcharge, if any (D) All the above

Last Answer : Answer: Option D

The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on (A) Top face perpendicular to wall (B) Bottom face perpendicular to wall (C) Both top and bottom faces perpendicular to wall (D) None of these

Description : The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on (A) Top face perpendicular to wall (B) Bottom face perpendicular to wall (C) Both top and bottom faces perpendicular to wall (D) None of these

Last Answer : Answer: Option A

In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed as a cantilever The correct answer is (A) (i) and (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Description : In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed ... (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option A

Americans roll joints with 2 tapered ends, Europeans roll them like a funnel--how do they do it without the smoke falling out?

Description : Americans roll joints with 2 tapered ends, Europeans roll them like a funnel--how do they do it without the smoke falling out?

Last Answer : The answer is cultural and technological superiority.

Moment of Inertia of triangular section about an axis passing through its base is given by a.bh3/12 b.bh3/32 c.bh3/36 d.None of the above e.Tapered bearing

Description : Moment of Inertia of triangular section about an axis passing through its base is given by a.bh3/12 b.bh3/32 c.bh3/36 d.None of the above e.Tapered bearing

Last Answer : a. bh3/12

A mass of 5 kg moves on a smooth horizontal plane with a speed of 8 m/s attached to a fixed point on the plane by a string of length 4m. Tension in the string is a.785 b.80N c.392.4N d.None of the above e.Tapered bearing

Description : A mass of 5 kg moves on a smooth horizontal plane with a speed of 8 m/s attached to a fixed point on the plane by a string of length 4m. Tension in the string is a.785 b.80N c.392.4N d.None of the above e.Tapered bearing

Last Answer : b. 80N

A man pulls a cart with 100 N force from rest with an acceleration of 10 m/sec2 for 10 seconds. The work done by him is a.500 KJ b.50.96 KJ c.101.92 KJ d.None of the above e.Tapered bearing

Description : A man pulls a cart with 100 N force from rest with an acceleration of 10 m/sec2 for 10 seconds. The work done by him is a.500 KJ b.50.96 KJ c.101.92 KJ d.None of the above e.Tapered bearing

Last Answer : a. 500 KJ

Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Description : Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Last Answer : b. 163.5 KW

A man lifts a stone weighting 300 g from the ground to a height of 2m and throws it horizontally with a velocity of 6 m/sec. The work done by the man is a.7.686 J b.11.286 J c.5.886 J d.8.343 J e.Tapered bearing

Description : A man lifts a stone weighting 300 g from the ground to a height of 2m and throws it horizontally with a velocity of 6 m/sec. The work done by the man is a.7.686 J b.11.286 J c.5.886 J d.8.343 J e.Tapered bearing

Last Answer : b. 11.286 J

Which of the following bearing will have least coefficient of friction a.Single ball bearing b.Cylinderical roller bearing c.Self aligury bearing d.Thrust ball bearing e.Tapered bearing

Description : Which of the following bearing will have least coefficient of friction a.Single ball bearing b.Cylinderical roller bearing c.Self aligury bearing d.Thrust ball bearing e.Tapered bearing

Last Answer : e. Tapered bearing

Work done by a body of mass 100 kg moving along a circular path of radius 2 m with a uniform velocity of 10 m/sec is a.5000 J b.2500 J c.509.68 J d.None of the above e.Tapered bearing

Description : Work done by a body of mass 100 kg moving along a circular path of radius 2 m with a uniform velocity of 10 m/sec is a.5000 J b.2500 J c.509.68 J d.None of the above e.Tapered bearing

Last Answer : d. None of the above

M.I. of sphere of 0.5 m radius about a mutually perpendicular axis (Z-axis) when its M.I. about X-axis and Y-axis are 50 kgm2 and 50 kgm2 is a.50 Kgm2 b.Tapered bearing c.100 Kgm2 d.25 Kgm2 e.12.5 Kgm2

Description : M.I. of sphere of 0.5 m radius about a mutually perpendicular axis (Z-axis) when its M.I. about X-axis and Y-axis are 50 kgm2 and 50 kgm2 is a.50 Kgm2 b.Tapered bearing c.100 Kgm2 d.25 Kgm2 e.12.5 Kgm2

Last Answer : a. 50 Kgm2

Minimum horsepower of pump required for filling 50m3 water tank, 20 metres high from ground in 30 minutes by lifting water from a well 5 metres below the ground level is a.5.45 KW b.7.5 KW c.6.81 KW d.Tapered bearing e.66.8 KW

Description : Minimum horsepower of pump required for filling 50m3 water tank, 20 metres high from ground in 30 minutes by lifting water from a well 5 metres below the ground level is a.5.45 KW b.7.5 KW c.6.81 KW d.Tapered bearing e.66.8 KW

Last Answer : c. 6.81 KW

The Leaning Tower of Pisa does not fall because (a) It is tapered at the top (b) It covers a large base area (c) Its centre of gravity remains at the lowest position (d) The vertical line through the centre of gravity of the tower falls within its base

Description : The Leaning Tower of Pisa does not fall because (a) It is tapered at the top (b) It covers a large base area (c) Its centre of gravity remains at the lowest position (d) The vertical line through the centre of gravity of the tower falls within its base

Last Answer : Ans:(d)

Air gap readings should be periodicly taken for electrical generation equipment. The best tool to use to take these measurements is a ___________. A. cloth (non-metalic) tape measure B. dial indicator C. inside micrometer D. tapered, long blade, feeler gage

Description : Air gap readings should be periodicly taken for electrical generation equipment. The best tool to use to take these measurements is a ___________. A. cloth (non-metalic) tape measure B. dial indicator C. inside micrometer D. tapered, long blade, feeler gage

Last Answer : Answer: D

The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Description : The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Last Answer : (a) needle roller bearings

The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Description : The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Last Answer : (b) separable

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads

What is a tapered-land thrust bearing?

Description : What is a tapered-land thrust bearing?

Last Answer : The babbitt face of a tapered-land thrust bearing has a series of fixed pads divided by radial slots. The leading edge of each sector is tapered, allowing an oil wedge to build up and carry the thrust between the collar and pad.

The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.

Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.

Last Answer : B. Tapered roller bearing.

6 A patient of chronic bronchial asthma was maintained on oral prednisolone 20 mg/day for 3 months. It was decided to switch him over to inhaled beclomethasone dipropionate 200 μg 4 times a day. What should be done to the oral prednisolone medication after starting inhaled beclomethasone: A. It should be stopped immediately B. Its dose should be tapered from the next day C. It should be given at the same dose for one week and then tapered D. Its dose should be doubled for one week and then tapered (p. 2

Description : 6 A patient of chronic bronchial asthma was maintained on oral prednisolone 20 mg/day for 3 months. It was decided to switch him over to inhaled beclomethasone dipropionate 200 μg 4 times a day. What should ... week and then tapered D. Its dose should be doubled for one week and then tapered (p. 2

Last Answer : C. It should be given at the same dose for one week and then tapered

The wheels of a train, engine as well as bogies, are slightly tapered to?

Last Answer : The wheels of a train, engine as well as bogies, are slightly tapered to facilitate in taking turns.

If the failure of a finite slope occurs through the toe, it is known as (A) Slope failure (B) Face failure (C) Base failure (D) Toe failure

Description : If the failure of a finite slope occurs through the toe, it is known as (A) Slope failure (B) Face failure (C) Base failure (D) Toe failure

Last Answer : (D) Toe failure

In a purely cohesive soil, the critical centre lies at the intersection of (A) Perpendicular bisector of slope and the locus of the centre (B) Perpendicular drawn at 1/3rd slope from toe and the locus of the centre (C) Perpendicular drawn at 2/3rd slope from toe and the locus of the centre (D) Directional angles

Description : In a purely cohesive soil, the critical centre lies at the intersection of (A) Perpendicular bisector of slope and the locus of the centre (B) Perpendicular drawn at 1/3rd slope from toe and the ... C) Perpendicular drawn at 2/3rd slope from toe and the locus of the centre (D) Directional angles

Last Answer : Answer: Option D

The shearing force acting along the slice of a curved surface of slippage, causes the soil to slide (A) Down at the centre (B) Down at the toe (C) Upward at the centre (D) None of these

Description : The shearing force acting along the slice of a curved surface of slippage, causes the soil to slide (A) Down at the centre (B) Down at the toe (C) Upward at the centre (D) None of these

Last Answer : Answer: Option A

Seepage through foundation in an earthen dam is controlled by providing (A) Rock toe (B) Horizontal blanket (C) Impervious cut off (D) Chimney drain

Description : Seepage through foundation in an earthen dam is controlled by providing (A) Rock toe (B) Horizontal blanket (C) Impervious cut off (D) Chimney drain

Last Answer : Answer: Option C

The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) Bottom face perpendicular to the wall The correct answer is (A) Only (ii) is correct (B) (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Description : The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) ... (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct

Last Answer : Answer: Option D

A station where the rail lines end, is called? A. Terminal station B. Junction Station C. Block Station D. Way-side-station

Description : A station where the rail lines end, is called? A. Terminal station B. Junction Station C. Block Station D. Way-side-station

Last Answer : A [Terminal station] Explanation: A "terminus" or "terminal" is a station at the end of a railway line. Trains arriving there have to end their journeys (terminate) or reverse out of the station.

A station where the rail lines end, is called (a) junction station (b) way-side-station (c) block station (d) terminal station

Description : A station where the rail lines end, is called (a) junction station (b) way-side-station (c) block station (d) terminal station

Last Answer : (d) terminal station

In new Rail as well as second hand rails how much end bends of the rails in lateral direction are permitted when checked with one metre straight edge before welding? (i) ± 0.2 mm in lateral direction (ii) ± 0.3 mm in lateral direction (iii) ± 0.5 mm in latera

Description : In new Rail as well as second hand rails how much end bends of the rails in lateral direction are permitted when checked with one metre straight edge before welding? (i) ± 0.2 mm in lateral direction (ii) ± 0.3 mm in lateral direction (iii) ± 0.5 mm in latera

Last Answer : (iii) ± 0.5 mm in latera

In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Description : In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Last Answer : (i) +0.5mm, -0 mm in vertical *

The rail joint should be located at ----------- from the end of level crossing a) 2 meters b) 3 meters * c) 5 meters d)6 meters

Description : The rail joint should be located at ----------- from the end of level crossing a) 2 meters b) 3 meters * c) 5 meters d)6 meters

Last Answer : b) 3 meters

If we had claws/wings/tails/horns/etc we would have to go to a claw/wing/tail/horn/etc salon when we had a fancy party or wanted to look nice. How would fashion trends, daily life inconveniences, clothes design change if we had other animal body parts?

Description : If we had claws/wings/tails/horns/etc we would have to go to a claw/wing/tail/horn/etc salon when we had a fancy party or wanted to look nice. How would fashion trends, daily life inconveniences, clothes design change if we had other animal body parts?

Last Answer : Having horns would give a brand new meaning to giving head

If we had claws/wings/tails/horns/etc we would have to go to a claw/wing/tail/horn/etc salon when we had a fancy party or wanted to look nice. How would fashion trends, daily life inconveniences, clothes design change if we had other animal body parts?

Description : If we had claws/wings/tails/horns/etc we would have to go to a claw/wing/tail/horn/etc salon when we had a fancy party or wanted to look nice. How would fashion trends, daily life inconveniences, clothes design change if we had other animal body parts?

Last Answer : Having horns would give a brand new meaning to giving head

Two aircrafts, one with a sharp wing profile (S) and the other with a thick profile (T), are flying through the same cloud with the same true airspeed. The cloud consists of small supercooled droplets. Which of the following statements is most correct concerning ice accretion? a. Aircraft T experiences more icing than S b. Aircraft S and T experience the same amount of icing c. Neither of the aircrafts accumulate ice due to the small size of droplets d. Aircraft S experiences more icing than T

Description : Two aircrafts, one with a sharp wing profile (S) and the other with a thick profile (T), are flying  through the same cloud with the same true airspeed. The cloud consists of small  ... aircrafts accumulate ice due to the small size of droplets  d. Aircraft S experiences more icing than T

Last Answer : d. Aircraft S experiences more icing than T