A cylinder rotor generator delivers 0.5 pu power in the steady-state to an infinite bus through a transmission

A cylinder rotor generator delivers 0.5 pu power in the steady-state to an infinite bus through a transmission line of reactance 0.5 pu. The generator no-load voltage is 1.5 pu and the infinite bus voltage is 1 pu. The inertia constant of the generator is 5 MW -s MVA / and the generator reactance is 1 pu. The critical clearing angle, in degrees, for a three-phase dead short circuit fault at the generator terminal is 

(A) 53.5 (B) 60.2 (C) 70.8 (D) 79.6
by

1 Answer

Answer :

A cylinder rotor generator delivers 0.5 pu power in the steady-state to an infinite bus through a transmission line of reactance 0.5 pu. The generator no-load voltage is 1.5 pu and the infinite bus voltage is 1 pu. The inertia constant of the generator is 5 MW -s MVA / and the generator reactance is 1 pu. The critical clearing angle, in degrees, for a three-phase dead short circuit fault at the generator terminal is 79.6

by

Related questions

A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals

Description : A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals. Assuming the prime mover input and the voltage behind the transient reactance to remain constant immediately after the fault, acceleration of the generator rotor is

Last Answer : A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals. Assuming the prime mover input and the voltage behind the transient reactance ... , acceleration of the generator rotor is inversely proportional to the moment of inertia of the machine

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage

Description : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

Last Answer : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he 0.52

The inertia constant of a 100 MVA, 11 kV water wheel generator is 4. The energy stored in the rotor at the

Description : The inertia constant of a 100 MVA, 11 kV water wheel generator is 4. The energy stored in the rotor at the synchronous speed is: A) 400 Mega Joule B) 400 Kilo Joule C) 25 Mega Joule D) 25 Kilo Joule

Last Answer : The inertia constant of a 100 MVA, 11 kV water wheel generator is 4. The energy stored in the rotor at the synchronous speed is: 400 Mega Joule

A synchronous generator is feeding power to infinite bus bars at unity power factor. Its excitation is now...

Description : A synchronous generator is feeding power to infinite bus bars at unity power factor. Its excitation is now increased. It will feed (a) The same power but at a leading power factor (b) The same power ... a lagging power factor (c) More power at unity power factor (d) Less power at unity power factor

Last Answer : A synchronous generator is feeding power to infinite bus bars at unity power factor. Its excitation is now increased. It will feed The same power but at a lagging power factor 

The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu

Description : The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are (A) 0.5 pu ... pu, 0.5 pu (C) 0.707 pu, 0.707 pu (D) 0.5 pu, 0.5 pu

Last Answer : The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are 0.866 pu, 0.5 pu

A generator is connected through a 20 MVA, 13.8/138 kV step down transformer, to a transmission line.

Description : A generator is connected through a 20 MVA, 13.8/138 kV step down transformer, to a transmission line. At the receiving end of the line a load is supplied through a step down transformer of 10 MVA, 138/69 kV rating. A 0.72 ... load (in per unit) in generator will be (A) 36 (B) 1.44 (C) 0.72 (D) 0.18

Last Answer : A generator is connected through a 20 MVA, 13.8/138 kV step down transformer, to a transmission line. At the receiving end of the line a load is supplied through a step down transformer of 10 MVA, 138/ ... MVA and 69 kV in load circuit, the value of the load (in per unit) in generator will be 36 

If a 5-bus test system contains 6 transmission lines and one transformer, how many non- zero elements are

Description : If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19

Last Answer : If a 5-bus test system contains 6 transmission lines and one transformer, 19 non-zero elements are there in the system Y-bus.

A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each...

Description : A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each conductor is 0.5 ohm / km. Receiving end voltage is 33 kV. If the line loss is not to exceed 10%, determine the length of the line.  (A) 7 km (B) 27.9 km (C) 56.8 km (D) 13.9 km

Last Answer : B

The steady state stability of the power system can be improved by

Description : The steady state stability of the power system can be improved by (A) using machines of high impedance (B) connecting transmission lines in series. (C) connecting lines in parallel. (D) reducing, the excitation of the machines.

Last Answer : The steady state stability of the power system can be improved by connecting lines in parallel.

A 3-phase 11 kV generator feeds power to a constant power unity power factor load of 100 MW through a

Description : A 3-phase 11 kV generator feeds power to a constant power unity power factor load of 100 MW through a 3-phase transmission line. The line-to line voltage at the terminals of the machine is maintained constant at 11 kV. The per ... 11 kV is  (A) 100 MVAR (B) 10.1 MVAR (C) -100 MVAR (D) -10.1 MVAR

Last Answer : A 3-phase 11 kV generator feeds power to a constant power unity power factor load of 100 MW through a 3-phase transmission line. The line-to line voltage at the terminals of the machine is maintained ... load to increase the line-to-line voltage at the load terminals to 11 kV is -10.1 MVAR

The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the bearings C. strictly converted to heat generated by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Description : The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the ... by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Last Answer : Answer: A

The steady state stability limit as compared to the transient state stability limit is always

Description : The steady state stability limit as compared to the transient state stability limit is always

Last Answer : The steady state stability limit as compared to the transient state stability limit is always Greater

A 50 Hz, 4-pole, 500 MVA, 22 kV turbo-generator is delivering rated megavolt amperes at 0.8 power factor.

Description : A 50 Hz, 4-pole, 500 MVA, 22 kV turbo-generator is delivering rated megavolt amperes at 0.8 power factor. Suddenly a fault occurs reducing in electric power output by 40%. Neglect losses and assume constant power input to the ... the time of fault will be  (A) 1.528 (B) 1.018 (C) 0.848 (D) 0.509

Last Answer : A 50 Hz, 4-pole, 500 MVA, 22 kV turbo-generator is delivering rated megavolt amperes at 0.8 power factor. Suddenly a fault occurs reducing in electric power output by 40%. Neglect losses and assume ... the shaft. The accelerating torque in the generator in MNm at the time of fault will be 1.018 

If shunt generator delivers 100 A at 200 V, and the resistance of the shunt field and armature are...

Description :  If shunt generator delivers 100 A at 200 V, and the resistance of the shunt field and armature are 100 ohm and 0.01 ohm respectively, the generated e.m.f. will be : -  a) 212 V b) 205 V c) 210 V d) 201.02 V

Last Answer :  If shunt generator delivers 100 A at 200 V, and the resistance of the shunt field and armature are 100 ohm and 0.01 ohm respectively, the generated e.m.f. will be : - 201.02 V

Pick out the correct statement. (A) Higher hold up of the solid in the rotary dryer results in better exposure of the solids to the gas (B) The 'Hatta number' is important in problems involving gas absorption without chemical reaction (C) For a non-reacting binary mixture of ideal gases, the partial pressure distribution of both components is linear in the case of steady state equimolal counter-diffusion (D) Total reflux in case of distillation operation requires infinite number of plates for a binary system separation

Description : Pick out the correct statement. (A) Higher hold up of the solid in the rotary dryer results in better exposure of the solids to the gas (B) The 'Hatta number' is ... reflux in case of distillation operation requires infinite number of plates for a binary system separation

Last Answer : (C) For a non-reacting binary mixture of ideal gases, the partial pressure distribution of both components is linear in the case of steady state equimolal counter-diffusion

The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Description : The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a (A) dc machine. (B) 3 phase induction machine. (C) synchronous machine. (D) single phase induction machine.

Last Answer : Ans: all options are correct

During a disturbance on a synchronous machine, the rotor swings form A to B before finally setting down to

Description : During a disturbance on a synchronous machine, the rotor swings form A to B before finally setting down to steady state at point C on the power angle curve. The speed of the machine during oscillation is synchronous at point(s)

Last Answer : During a disturbance on a synchronous machine, the rotor swings form A to B before finally setting down to steady state at point C on the power angle curve. The speed of the machine during oscillation is synchronous at point(s) only at C

A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady

Description : A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady short-circuit line current of   (a) 250A (b) 50 A (c) 150 A (d) 350 A 

Last Answer : A 10 kVA, 400 V/200 V single phase transformer with 10% impedance draws a steady short-circuit line current of 250A

If the reference bus is changed in two load flow runs with same system data and power obtained for

Description : If the reference bus is changed in two load flow runs with same system data and power obtained for reference bus taken as specified P and Q in the latter run, the system losses  A) Will be ... C) As well as complex bus voltage will changed D) As well as complex bus voltage will be unchanged

Last Answer : If the reference bus is changed in two load flow runs with same system data and power obtained for reference bus taken as specified P and Q in the latter run, the system losses Will be unchanged but complex bus voltages will change

The number of natural frequency in two rotor system is A Zero B Infinite C Two D One

Description : The number of natural frequency in two rotor system is A Zero B Infinite C Two D One

Last Answer : C Two

The number of natural frequencies in a two rotor system is A. Infinite B. Zero C. Two D. Four

Description : The number of natural frequencies in a two rotor system is A. Infinite B. Zero C. Two D. Four

Last Answer : C. Two

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

The zero sequence current of a generator for line to ground fault is j 2.4 p.u. The current through the neutral

Description : The zero sequence current of a generator for line to ground fault is j 2.4 p.u. The current through the neutral during the fault is (a) j 0.8 p.u (b) j 2.4 p.u. (c) j 0.24 p.u. (d) j 7.2 p.u. 

Last Answer : j7.2

For optimum generator scheduling for different power plants, the minimum fuel cost is obtained when

Description : For optimum generator scheduling for different power plants, the minimum fuel cost is obtained when

Last Answer : For optimum generator scheduling for different power plants, the minimum fuel cost is obtained when The incremental fuel cost of each plant multiplied by the penalty factor is the same

The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and

Description : The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is (A) 0.25 pu (B) 0.5 pu (C) 1.0 pu (D) 1.5 pu

Last Answer : The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is 0.5 pu

In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Description : In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Last Answer : Answer: A

In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Last Answer : Answer: C

An 800 kV transmission line has a maximum power transfer capacity of P. If it is operated at 400 kV with the

Description : An 800 kV transmission line has a maximum power transfer capacity of P. If it is operated at 400 kV with the series reactance unchanged, the new maximum power transfer capacity is approximately (A) P (B) 2P (C) P / 2 (D) P / 4

Last Answer : An 800 kV transmission line has a maximum power transfer capacity of P. If it is operated at 400 kV with the series reactance unchanged, the new maximum power transfer capacity is approximately P / 4

For enhancing the power transmission in along EHV transmission line, the most preferred method is to

Description : For enhancing the power transmission in along EHV transmission line, the most preferred method is to connect a  (A) Series inductive compensator in the line (B) Shunt inductive compensator at the ... (C) Series capacitive compensator in the line (D) Shunt capacitive compensator at the sending end

Last Answer : For enhancing the power transmission in along EHV transmission line, the most preferred method is to connect a Series capacitive compensator in the line

For a fixed value of complex power flow in a transmission line having a sending and voltage V, the real

Description : For a fixed value of complex power flow in a transmission line having a sending and voltage V, the real power loss will be proportional to  A) V B) v2 C) 1/V2 D)1/V

Last Answer : For a fixed value of complex power flow in a transmission line having a sending and voltage V, the real power loss will be proportional to 1/V2

The power flow problem mathematical model for a linear transmission network

Description : The power flow problem mathematical model for a linear transmission network (A) is non-linear (B) is linear (C) considers time variation of generation (D) does not consider tap-changing transformers

Last Answer : The power flow problem mathematical model for a linear transmission network is non-linear

The transmission line feeding power on either side of the main transmission line is called?

Description : The transmission line feeding power on either side of the main transmission line is called?

Last Answer : The transmission line feeding power on either side of the main transmission line is called Secondary transmission.

For a transmission line with negligible losses, the lagging reactive power...

Description : For a transmission line with negligible losses, the lagging reactive power (VAR) delivered at The receiving end, for a given receiving end voltage, is directly proportional to the?

Last Answer : For a transmission line with negligible losses, the lagging reactive power (VAR) delivered at The receiving end, for a given receiving end voltage, is directly proportional to the line voltage drop.

Filling of gas from a high pressure cylinder into small bottles is an example of a/an __________ process. (A) Equilibrium (B) Adiabatic (C) Steady (D) Unsteady

Description : Filling of gas from a high pressure cylinder into small bottles is an example of a/an __________ process. (A) Equilibrium (B) Adiabatic (C) Steady (D) Unsteady

Last Answer : (D) Unsteady

A single-phase transmission line of impedance j 0.8 ohm supplies a resistive...

Description :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

Last Answer :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is 0.6 lagging.

If a voltage-controlled bus is treated as load bus, then which one of the following limits would be

Description : If a voltage-controlled bus is treated as load bus, then which one of the following limits would be violated?   (a) Active power (b) Reactive power (c) Voltage (d) Phase angle 

Last Answer : If a voltage-controlled bus is treated as load bus, then which one of the following limits would be violated?   (a) Active power (b) Reactive power (c) Voltage (d) Phase angle 

In load flow Study, a PV bus is treated as a PQ bus when

Description : In load flow Study, a PV bus is treated as a PQ bus when

Last Answer : Voltage at the bus becomes high 

In load flow analysis, the load connected at a bus is represented as?

Description : In load flow analysis, the load connected at a bus is represented as?

Last Answer : constant real and reactive powers drawn from bus

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Description : As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Last Answer : Answer: C

The steady-state fault current during a 3 phase terminal fault on a generator is limited by:

Description : The steady-state fault current during a 3 phase terminal fault on a generator is limited by: (1) Transient reactance of the generator (2) Sub-transient reactance of the generator (3) Synchronous reactance of the generator (4) DC off—set during the instant of the fault

Last Answer : 1

A 4 bus power system consists of 4 transmission lines, then find the sparsity of Y bus matrix? a) 0.75 b) 0.25 c) 0.4 d) 0.5

Description : A 4 bus power system consists of 4 transmission lines, then find the sparsity of Y bus matrix? a) 0.75 b) 0.25 c) 0.4 d) 0.5

Last Answer : b) 0.25

How does increase in steam input of the Alternator connected to infinite bus-bars affect this operation?

Description : How does increase in steam input of the Alternator connected to infinite bus-bars affect this operation?

Last Answer : KW output power of alternator increase with increase in steam input keeping excitation constant.

How does increase in excitation of the Alternator connected to infinite bus-bars affect this operation?

Description : How does increase in excitation of the Alternator connected to infinite bus-bars affect this operation?

Last Answer : Increase in excitation level of the synchronous generator will effectively increase the reactive power supplied by the generator keeping steam input constant.

What is meant by infinite bus-bars?

Description : What is meant by infinite bus-bars?

Last Answer : The source or supply lines with non-variable voltage and frequency are called infinite bus-bars. The source lines are said to have zero source impedance and infinite rotational inertia.

A three phase, salient pole synchronous motor is connected to an infinite bus. It is operated at no load a

Description : A three phase, salient pole synchronous motor is connected to an infinite bus. It is operated at no load a normal excitation. The field excitation of the motor is first reduced to zero ... First increases and then decreases steeply (C) First decreases and then increases steeply (D) Remains constant

Last Answer : B

The steam input in to a turbogenerator connected to infinite bus is increased. Which of the events will take...

Description : The steam input in to a turbogenerator connected to infinite bus is increased. Which of the events will take place? (a) The generator will feed more leading KVAR to bus bar and power angle will not ... decrease (d) The generator will feed more lagging KVAR to bus bar and power angle will not change

Last Answer : The steam input in to a turbogenerator connected to infinite bus is increased. Which of the events will take place? (a) The generator will feed more leading KVAR to bus bar and power angle will ... decrease (d) The generator will feed more lagging KVAR to bus bar and power angle will not change

An alternator with frequency f1 is to be synchronized with an infinite bus of frequency f....

Description : An alternator with frequency f1 is to be synchronized with an infinite bus of frequency f. For proper synchronization (1) f1=f (2) f1<f (3)f1>f (4) either (b) or (c) 

Last Answer : A