Which of the following is a device used on a tractor or stationary engine for maintaining nearly constant engine speed under varying loads? 1. Volatility of fuel 2. Governor 3. Pre-ignition 4. carburetor

Which of the following is a device used on a tractor or stationary engine for maintaining nearly constant engine speed under varying loads? 1. Volatility of fuel 2. Governor 3. Pre-ignition 4. carburetor
by

1 Answer

Answer :

<!-- [if !supportLists] -->1.   <!-- [endif] -->ans 2

 


by

Related questions

In tractor engine which of the following is a device in which liquid fuel is converted into gaseous fuel? 1. Piston 2. Carburetor 3. Both 1 and 2 4. none of these ans 1

Description : In tractor engine which of the following is a device in which liquid fuel is converted into gaseous fuel? 1. Piston 2. Carburetor 3. Both 1 and 2 4. none of these ans 1

Last Answer : ans 1

Pressure in a Pressurised Water Reactor (PWR) is used for (A) Maintaining constant pressure in the primary cooling circuit under varying loads (B) Superheating the steam (C) Pressurising the water in the primary coolant circuit (D) None of these

Description : Pressure in a Pressurised Water Reactor (PWR) is used for (A) Maintaining constant pressure in the primary cooling circuit under varying loads (B) Superheating the steam (C) Pressurising the water in the primary coolant circuit (D) None of these

Last Answer : (A) Maintaining constant pressure in the primary cooling circuit under varying loads

Rate of burning in the compression ignition engine can be controlled by a. rate of injection of fuel b. rate of air taken into carburetor c. both a. and b. d. none of the above

Description : Rate of burning in the compression ignition engine can be controlled by a. rate of injection of fuel b. rate of air taken into carburetor c. both a. and b. d. none of the above

Last Answer : ANSWER a. rate of injection of fuel

The air-fuel ratio of the petrol engine is governed by A. fuel pump B. governor C. carburetor D. injector

Description : The air-fuel ratio of the petrol engine is governed by A. fuel pump B. governor C. carburetor D. injector

Last Answer : ANSWER : C

Which section of the circuit is responsible for maintaining a nearly constant voltage for all loads within its operating range? EL-0085 A. I B. II C. III D. IV

Description : Which section of the circuit is responsible for maintaining a nearly constant voltage for all loads within its operating range? EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: D

The violent noises heard in an engine during the process of combustion after the position has passed over the top dead center is known as? 1. Stationary 2. Spark ignition 3. Detonation 4. all of these

Description : The violent noises heard in an engine during the process of combustion after the position has passed over the top dead center is known as? 1. Stationary 2. Spark ignition 3. Detonation 4. all of these

Last Answer :     <!-- [endif] -->ans 3

Which of the following types of internal combustion engine is generally used as portable engine for pumping and electricity generation? 1. Spark ignition 2. Stationary 3. Vertical single cylinder 3. all of these

Description : Which of the following types of internal combustion engine is generally used as portable engine for pumping and electricity generation? 1. Spark ignition 2. Stationary 3. Vertical single cylinder 3. all of these

Last Answer : ans 2

By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Description : By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Last Answer : Ans : d

In the illustration, the contacts between terminals 26 and 27 should be closed when _________. EL-0046 A. using one generator in isochronous mode only B. using two or more generators in parallel only C. the prime mover speed is to remain constant through varying loads in parallel or single operation D. the circuit breaker is closed for that generator

Description : In the illustration, the contacts between terminals 26 and 27 should be closed when _________. EL-0046 A. using one generator in isochronous mode only B. using two or more generators in ... through varying loads in parallel or single operation D. the circuit breaker is closed for that generator

Last Answer : Answer: C

Suggest the different methods to control the speed of rotation of steam turbine constant at all varying loads.

Description : Suggest the different methods to control the speed of rotation of steam turbine constant at all varying loads.

Last Answer : Following are the different methods to control the speed of rotation of steam turbine constant at all varying loads;  a) Throttle governing b) Nozzle control governing c) By pass governing d) Combine throttle and nozzle control governing e) Combine throttle and by pass governing

onstant speed governors are used on ∙ Tractor engine diesel ∙ Stationary diesel engine ∙ Petrol engine ∙ None of the above

Description : onstant speed governors are used on ∙ Tractor engine diesel ∙ Stationary diesel engine ∙ Petrol engine ∙ None of the above

Last Answer : Stationary diesel engine

variable speed governors are used on ∙ Tractor engine(diesel) ∙ Stationary engine (diesel) ∙ Petrol engine ∙ None of the above

Description : variable speed governors are used on ∙ Tractor engine(diesel) ∙ Stationary engine (diesel) ∙ Petrol engine ∙ None of the above

Last Answer : ∙ Tractor engine(diesel)

The fuel air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as compared to clean filter will be A. higher B. lower C. remain unaffected D. unpredictable

Description : The fuel air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as compared to clean filter will be A. higher B. lower C. remain unaffected D. unpredictable

Last Answer : ANSWER : A

Vapour lock is a. complete or partial stoppage of fuel supply due to vaporization of the fuel b. locking of carburetor due to high vapor pressure c. excess fuel supply to the engine d. supply of liquid fuel to the engine

Description : Vapour lock is a. complete or partial stoppage of fuel supply due to vaporization of the fuel b. locking of carburetor due to high vapor pressure c. excess fuel supply to the engine d. supply of liquid fuel to the engine

Last Answer : ANSWER a. complete or partial stoppage of fuel supply due to vaporization of the fuel

Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold

Description : Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold

Last Answer : ANSWER c. engine cylinder

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

Tractor drawn disc harrows have concave discs of size varying from… diameter. a. 55-90cm b. 60-100cm d. None of the above

Description : Tractor drawn disc harrows have concave discs of size varying from… diameter. a. 55-90cm b. 60-100cm d. None of the above

Last Answer : Ans - c. 35-70cm

The change in flux linkages can be caused in which ofthe following ways ? (a) The flux is constant with respect to time and is stationary and the coil moves through it (b) The coil is stationary with respect to flux and the flux varies in magnitude with respect to time (c) Both the changes mentioned above occure together, i.e., the coil moves through a time varying field (d) All ofthe above

Description : The change in flux linkages can be caused in which ofthe following ways ? (a) The flux is constant with respect to time and is stationary and the coil moves through it (b) The coil is stationary with ... above occure together, i.e., the coil moves through a time varying field (d) All ofthe above

Last Answer : (d) All ofthe above

The speed of a 4-pole induction motor is controlled by varying the supply frequency while maintaining the

Description : The speed of a 4-pole induction motor is controlled by varying the supply frequency while maintaining the ratio of supply voltage to supply frequency (V/f ) constant. At rated frequency of 50 Hz and rated voltage of 400 V ... load torque is constant  (A) 882 rpm (B) 864 rpm (C) 840 rpm (D) 828 rpm

Last Answer : The speed of a 4-pole induction motor is controlled by varying the supply frequency while maintaining the ratio of supply voltage to supply frequency (V/f ) constant. At rated frequency of 50 Hz and rated voltage of 400 ... torque is constant  (A) 882 rpm (B) 864 rpm (C) 840 rpm (D) 828 rpm

The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. all of the above

Description : The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. all of the above

Last Answer : ANSWER d. all of the above

The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. All of the above

Description : The probability of knocking in diesel engines is increased by a. High self-ignition temperature. b. Low volatility. c. High viscosity. d. All of the above

Last Answer : ANSWER d. all of the above

The speed of a series wound winch motor is controlled by ____________. A. varying the voltage applied to the motor B. the weight of the load on the cargo boom C. overcurrent protection devices in the motor D. a hydraulic speed-limiting governor

Description : The speed of a series wound winch motor is controlled by ____________. A. varying the voltage applied to the motor B. the weight of the load on the cargo boom C. overcurrent protection devices in the motor D. a hydraulic speed-limiting governor

Last Answer : Answer: A

Which of the following statement is incorrect?  A. The liquid fuels consist of hydrocarbons.  B. The liquid fuels have higher calorific value than solid fuels.  C. The solid fuels have higher calorific value than liquid fuels.  D. A good fuel should have low ignition point.

Description : Which of the following statement is incorrect?  A. The liquid fuels consist of hydrocarbons.  B. The liquid fuels have higher calorific value than solid fuels.  C. The solid fuels have higher calorific value than liquid fuels.  D. A good fuel should have low ignition point.

Last Answer : Answer: C

The tendency of knocking in CI engine reduces by (a) High self ignition temperature of fuel (b) Decrease in jacket water temperature (c) Injection of fuel just before TDC (d) Decrease in injection pressure

Description : The tendency of knocking in CI engine reduces by (a) High self ignition temperature of fuel (b) Decrease in jacket water temperature (c) Injection of fuel just before TDC (d) Decrease in injection pressure

Last Answer : Ans :c

Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Description : Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Last Answer : ANSWER a. fuel injector

Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Description : Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Last Answer : ANSWER d. all of the above

The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Description : The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Last Answer : ANSWER d. all the above

In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD winding through the voltage regulator. C. the controller to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Description : In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to ... from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Last Answer : Answer: A

If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but governor will not operate (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Description : If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but ... (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Last Answer : (A) The governor will not operate but flywheel will be acting

If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Description : If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Last Answer : b) Governor

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

What is the function of boiler? • To burn the fuel in a confined closed system With the supply of air • To generate steam in varying pressure • To generate steam at constant pressure • To produce flue gases by burning fuel at a given pressure

Description : What is the function of boiler? • To burn the fuel in a confined closed system With the supply of air • To generate steam in varying pressure • To generate steam at constant pressure • To produce flue gases by burning fuel at a given pressure

Last Answer : • To generate steam at constant pressure

In a simple carburetor, the air-fuel ratio increases when the A. density of air increases B. velocity of air increases C. velocity of air decreases D. density of air decreases

Description : In a simple carburetor, the air-fuel ratio increases when the A. density of air increases B. velocity of air increases C. velocity of air decreases D. density of air decreases

Last Answer : ANSWER : B

In a carburetor the level of the fuel in the float chamber as compared to the level of the main jet in the venture is A. lower B. same C. higher D. same or higher

Description : In a carburetor the level of the fuel in the float chamber as compared to the level of the main jet in the venture is A. lower B. same C. higher D. same or higher

Last Answer : ANSWER : A

Corresponding to Fig. (3), the loading on the portion AD of the beam will be (a) Uniformly distributed load (b) Uniformly varying load (c) Point loads (d) Cannot be said

Description : Corresponding to Fig. (3), the loading on the portion AD of the beam will be (a) Uniformly distributed load (b) Uniformly varying load (c) Point loads (d) Cannot be said

Last Answer : (a) Uniformly distributed load

When the bending moment is parabolic curve between two points, it indicates that there is (a) No loading between the two points (b) Point loads between the two points (c) U.D.L. between the two points (d) Uniformly varying load between the two points

Description : When the bending moment is parabolic curve between two points, it indicates that there is (a) No loading between the two points (b) Point loads between the two points (c) U.D.L. between the two points (d) Uniformly varying load between the two points

Last Answer : (c) U.D.L. between the two points

The degree of the B-spline with varying knot vectors a.Increases with knot vectors b.Decreases with knot vectors c.Remains constant d.none of the above

Description : The degree of the B-spline with varying knot vectors a.Increases with knot vectors b.Decreases with knot vectors c.Remains constant d.none of the above

Last Answer : a.Increases with knot vectors

Even though the main engine runs at varying speeds, how does the alternator maintain constant frequency?

Description : Even though the main engine runs at varying speeds, how does the alternator maintain constant frequency?

Last Answer : By use of thyristor controlled frequency (rpm) converters.

Which engine has carburetor ?

Last Answer : Petrol engine has carburetor

Choke in a I.C. engine is used to control a) Camshaft speed b) Specific fuel consumption c) Air fuel mixture d) Crankshaft speed Ans. c

Description : Choke in a I.C. engine is used to control a) Camshaft speed b) Specific fuel consumption c) Air fuel mixture d) Crankshaft speed Ans. c

Last Answer : ans c

Compare detonation and diesel knock on the basis of (i) Fuel Ignition Temperature (ii) Compression Ratio (iii) Speed (iv) inlet temperature (v) inlet pressure (vi) cylinder wall temperature (vii) cylinder size

Description : Compare detonation and diesel knock on the basis of (i) Fuel Ignition Temperature (ii) Compression Ratio (iii) Speed (iv) inlet temperature (v) inlet pressure (vi) cylinder wall temperature (vii) cylinder size 

Last Answer : Comparison between detonation and diesel knock: Parameter To avoid Detonation in SI Engine  To avoid Diesel knock i) Fuel Ignition Temperature High Low ii) Compression Ratio ... Cylinder wall temperature Low High viii) Cylinder size Small Large

In tractor engine the complete path of power from the engine to the wheel is called 1. Power train 2. Power wheel 3. Both 1 and 2 4. none of these

Description : In tractor engine the complete path of power from the engine to the wheel is called 1. Power train 2. Power wheel 3. Both 1 and 2 4. none of these

Last Answer :     <!-- [endif] -->ans 1

Tractor engine oil should be changed and all grease points should be lubricated after every working hrs 1. 15 2. 30 3. 60 4. 120

Description : Tractor engine oil should be changed and all grease points should be lubricated after every working hrs 1. 15 2. 30 3. 60 4. 120

Last Answer : ans 4

Tractor engine is used as A. General purpose C. Special purpose B. Prime mover. D. None of the above

Description : . Tractor engine is used as A. General purpose C. Special purpose B. Prime mover. D. None of the above

Last Answer : Prime mover

Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Description : Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Last Answer : ANSWER : A

In a battery ignition system, the intensity of spark is A. minimum at low engine speed B. minimum at low engine speed and increases with engine speed C. maximum al low engine speed and decreases with engine speed D. maximum at low engine speed

Description : In a battery ignition system, the intensity of spark is A. minimum at low engine speed B. minimum at low engine speed and increases with engine speed C. maximum al low engine speed and decreases with engine speed D. maximum at low engine speed

Last Answer : ANSWER : C

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Last Answer : ANSWER c. Both a and b.

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Last Answer : ANSWER c. Both a and b

With increase in __________ Knocking tendency in a spark ignition petrol engine decreases. (A) Supercharging (B) Wall temperature (C) Compression ratio (D) Engine speed

Description : With increase in __________ Knocking tendency in a spark ignition petrol engine decreases. (A) Supercharging (B) Wall temperature (C) Compression ratio (D) Engine speed

Last Answer : Option D