Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code calls for a 4t bend. Which of the following rollers should be selected for the testing? a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter

Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code  calls for a 4t bend. Which of the following rollers should be selected for the testing?
a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter
by

1 Answer

Answer :

d) 32mm diameter
by

Related questions

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°? a) They should be acceptable as the standard refers to minimum forming angle b) The bends should be considered as fail c) New bends should be produced and bent to 180° then re-examined d) They should be rejected as the angle is not close enough to be acceptable

Description : When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°? a) They should be acceptable as ... then re-examined d) They should be rejected as the angle is not close enough to be acceptable

Last Answer : c) New bends should be produced and bent to 180° then re-examined

In welder qualification testing of 45mm plates, why are side bends used instead of root and face bends? a) They are easier to produce b) The testing equipment cannot handle thick root/face bends c) Root defects are not important for welder qualification d) They give more accurate indications

Description : In welder qualification testing of 45mm plates, why are side bends used instead of root and face bends? a) They are easier to produce b) The testing equipment cannot handle thick root/face bends c) Root defects are not important for welder qualification d) They give more accurate indications

Last Answer : d) They give more accurate indications

Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable

Description : Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable

Last Answer : a) The welding engineer

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

Which of the following pipe bends will incur the largest head loss?(A) U-bend (B) 30° bend (C) 45° bend (D) 90° bend

Description : Which of the following pipe bends will incur the largest head loss? (A) U-bend (B) 30° bend (C) 45° bend (D) 90° bend

Last Answer : (A) U-bend

The radius of a bar bend to form a hook, should not be less than (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Five times the diameter

Description : The radius of a bar bend to form a hook, should not be less than (A) Twice the diameter (B) Thrice the diameter (C) Four times the diameter (D) Five times the diameter

Last Answer : Answer: Option A

One end of a cylindrical rod is grounded to a hemispherical surface of radius`R=20mm`.It is immersed in water`(mu=4//3)`.If the refractive index of th

Description : One end of a cylindrical rod is grounded to a hemispherical surface of radius`R=20mm`.It is immersed in water`(mu=4//3)`.If the refractive index of th

Last Answer : One end of a cylindrical rod is grounded to a hemispherical surface of radius`R=20mm`.It is immersed in water`(mu ... is ................(determine)

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

Which of the following in NOT a quantitative test? a) Root bend b) Macro hardness c) Charpy d) Tensile

Description : Which of the following in NOT a quantitative test? a) Root bend b) Macro hardness c) Charpy d) Tensile

Last Answer : a) Root bend

A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Last Answer : (a) butt weld

The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (b) Throat of weld

If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Last Answer : (A) pd/2t

_________ of test specimens is not involved in any hardness testing method. (A) Fracture (B) Indentation (C) Wear (D) Scratch

Description : _________ of test specimens is not involved in any hardness testing method. (A) Fracture (B) Indentation (C) Wear (D) Scratch

Last Answer : (A) Fracture

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

What length of an alloy wire of resistivity 5.0x10^-7 Ωm and diameter 0.50mm is required to make a standard 6.0Ω resistor?

Description : What length of an alloy wire of resistivity 5.0x10^-7 Ωm and diameter 0.50mm is required to make a standard 6.0Ω resistor?

Last Answer : Interesting homework question. I’m not knowledgeable about physics, but putting myself in the shoes of someone who is.. Why don’t you post the answer that you got, and show your work, and ask us where you went wrong on the problem.

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Explain the different recording techniques used in method study. Also outline process chart for checking diameter of 50mm of shaft.

Description : Explain the different recording techniques used in method study. Also outline process chart for checking diameter of 50mm of shaft.

Last Answer : Different recording techniques used in method study: Process charts are used to record the data systematically so that none of the information needed for study and analysis is missed. A. Chart indicating ... area. However, there is no indication of the direction or speed of motion.

Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Last Answer : (b) False

The needle rollers are a maximum of _______ millimeter in diameter. (a) 4 (b) 5 (c) 6 (d) 7

Description : The needle rollers are a maximum of _______ millimeter in diameter. (a) 4 (b) 5 (c) 6 (d) 7

Last Answer : (b) 5

Needles bearing consist of rollers of small diameter and very small length. a) True b) False

Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False

Last Answer : b) False

The length/diameter ratio of cylindrical specimens used in triaxial test, is generally (A) 1 (B) 1.5 (C) 2 (D) 2.5

Description : The length/diameter ratio of cylindrical specimens used in triaxial test, is generally (A) 1 (B) 1.5 (C) 2 (D) 2.5

Last Answer : Answer: Option C

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

The diameter of bars used for distribution reinforcement in slabs, may vary from (a) 2 to 4mm (b) 4 to 6mm (c) 6mm to 8mm (d) 8 to 12mm

Description : The diameter of bars used for distribution reinforcement in slabs, may vary from (a) 2 to 4mm (b) 4 to 6mm (c) 6mm to 8mm (d) 8 to 12mm

Last Answer : (c) 6mm to 8mm

The diameter of bars for main reinforcement in slabs, may be (a) 2 to 4mm (b) 4 to 8mm (c) 8 to 14mm (d) 14 to 18mm

Description : The diameter of bars for main reinforcement in slabs, may be (a) 2 to 4mm (b) 4 to 8mm (c) 8 to 14mm (d) 14 to 18mm

Last Answer : (c) 8 to 14mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Description : These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Last Answer : C. constant-radius bending

Instructions for the patient with low back pain include which of the following? a) When lifting, avoid overreaching. Instructions for the patient with low back pain should include that when lifting, the patient should avoid overreaching. The patient should also keep the load close to the body, bend the knees and tighten the abdominal muscles, use a wide base of support, and use a back brace to protect the back.

Description : Instructions for the patient with low back pain include which of the following? a) When lifting, avoid overreaching. Instructions for the patient with low back pain should include that when lifting, ... lifting, the patient with low back pain should bend the knees and tighten the abdominal muscles.

Last Answer : a) When lifting, avoid overreaching. Instructions for the patient with low back pain should include that when lifting, the patient should avoid overreaching. The patient should also keep the load close to the ... muscles, use a wide base of support, and use a back brace to protect the back.

In case of a hair pin bend of a highway, (A) Minimum radius of inner curve is 14 m (B) Minimum radius of transition is 15 m (C) Circular compound curve may be provided (D) All the above

Description : In case of a hair pin bend of a highway, (A) Minimum radius of inner curve is 14 m (B) Minimum radius of transition is 15 m (C) Circular compound curve may be provided (D) All the above

Last Answer : Answer: Option D

A waveguide bend must have what minimum radius?

Description : A waveguide bend must have what minimum radius?

Last Answer : Greater than 2 wavelengths.

Type of bend that occurs as a result of differences in thermal contraction rates between the core and the cladding material. ∙ A. Macrobending ∙ B. Microbending ∙ C. Quad bending ∙ D. Constant-radius bending

Description : Type of bend that occurs as a result of differences in thermal contraction rates between the core and the cladding material. ∙ A. Macrobending ∙ B. Microbending ∙ C. Quad bending ∙ D. Constant-radius bending

Last Answer : B. Microbending

A flitched beam has a. Common neutral axis & both materials bend independently b. Common neutral axis & both materials has common R (Radius of curvature) c. Two neutral axis & both materials has common R (Radius of curvature) d. Two neutral axis & both materials bend independently

Description : A flitched beam has a. Common neutral axis & both materials bend independently b. Common neutral axis & both materials has common R (Radius of curvature) c. Two neutral axis & both materials has common R (Radius of curvature) d. Two neutral axis & both materials bend independently

Last Answer : b. Common neutral axis & both materials has common R (Radius of curvature)

In a recent research study initiated by Tel-E-Fone Telecommunications, survey calls were made to a randomly selected group in which every member has an equal chance of selection. This type of sample selection is called A. Probability sample B. Convenience sample C. Judgment sample D. Quota sample E. Area sample

Description : In a recent research study initiated by Tel-E-Fone Telecommunications, survey calls were made to a randomly selected group in which every member has an equal chance of selection. This type of sample selection ... sample B. Convenience sample C. Judgment sample D. Quota sample E. Area sample

Last Answer : A. Probability sample

Is there an Android app that prevents butt dialing and does not require many permissions?

Description : Is there an Android app that prevents butt dialing and does not require many permissions?

Last Answer : Something else you might try is to go into SETTINGS -> ACCESSIBILITY and set “Power button ends call”. This way, you don’t have to press the “end call” screen button, and you might not accidentally then hit another contact.

What is the diameter a hand bender can bend copper pipe?

Description : What is the diameter a hand bender can bend copper pipe?

Last Answer : Feel Free to Answer

The anchorage value of a hook is assumed sixteen times the diameter of the bar if the angle of the bend, is (A) 30° (B) 40° (C) 45° (D) All the above

Description : The anchorage value of a hook is assumed sixteen times the diameter of the bar if the angle of the bend, is (A) 30° (B) 40° (C) 45° (D) All the above

Last Answer : Answer: Option D

The Radius (or diameter) of bright rings in Newton’s rings is (a) Directly proportional to the square root of odd numbers (b) Inversely proportional to the square root of natural numbers (c) Directly proportional to the square root of even numbers (d) Directly proportional to the square root of natural numbers

Description : he Radius (or diameter) of bright rings in Newton's rings is (a) Directly proportional to the square root of odd numbers (b) Inversely proportional to the square root of natural numbers (c) ... to the square root of even numbers (d) Directly proportional to the square root of natural numbers

Last Answer : (a) Directly proportional to the square root of odd numbers

Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Description : Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Last Answer : b) False

During periodic testing of an AT weld with 700 probe, a bunch of moving signals of less than 40% but more than 10% is observed in the head of weld, the joint will be. (i) Good joint.* (ii) DFWR (iii) DFWO (iv) OBSW

Description : During periodic testing of an AT weld with 700 probe, a bunch of moving signals of less than 40% but more than 10% is observed in the head of weld, the joint will be. (i) Good joint.* (ii) DFWR (iii) DFWO (iv) OBSW

Last Answer : i) Good joint.*

By 00 probe in AT weld testing with normal gain setting. (i) Area below N.axis can be tested. (ii) Area below N.axis can not be tested.* (iii) Only web below N.axis can be tested. (iv) All above are correct.

Description : By 00 probe in AT weld testing with normal gain setting. (i) Area below N.axis can be tested. (ii) Area below N.axis can not be tested.* (iii) Only web below N.axis can be tested. (iv) All above are correct.

Last Answer : (ii) Area below N.axis can not be tested.*

USFD testing of new AT weld will be done by ? (i) JE/SSE sectional (ii) Incharge SSE (iii) USFD machine operator* (iv) None of the above

Description : USFD testing of new AT weld will be done by ? (i) JE/SSE sectional (ii) Incharge SSE (iii) USFD machine operator* (iv) None of the above

Last Answer : (iv) None of the above

After declare good in USFD testing what is the joggling criteria ? (i) Joggle will be open from the AT weld* (ii) Joggling with two far end bolting (iii) joggling with four tight bold (iv) None of the above

Description : After declare good in USFD testing what is the joggling criteria ? (i) Joggle will be open from the AT weld* (ii) Joggling with two far end bolting (iii) joggling with four tight bold (iv) None of the above

Last Answer : (i) Joggle will be open from the AT weld*

What is the testing frequency of new AT weld ? (i) Just after the welding (ii) After 7 days of welding (iii) With in the one month of welding* (iv) None of the above

Description : What is the testing frequency of new AT weld ? (i) Just after the welding (ii) After 7 days of welding (iii) With in the one month of welding* (iv) None of the above

Last Answer : iii) With in the one month of welding*

Till USFD testing of new AT weld what is criteria for joggling ? (i) Joggling with two far end bold (ii) Joggling with two tight clamps* (iii) Leave without joggling till its testing (iv) None of the above

Description : Till USFD testing of new AT weld what is criteria for joggling ? (i) Joggling with two far end bold (ii) Joggling with two tight clamps* (iii) Leave without joggling till its testing (iv) None of the above

Last Answer : (ii) Joggling with two tight clamps*

From a circular plate of diameter 6 cm is cut out a circle whose diameter is a radius of the plate. Find the e.g. of the remainder from the center of circular plate (A) 0.5 cm (B) 1.0 cm (C) 1.5 cm (D) 2.5 cm

Description : From a circular plate of diameter 6 cm is cut out a circle whose diameter is a radius of the plate. Find the e.g. of the remainder from the center of circular plate (A) 0.5 cm (B) 1.0 cm (C) 1.5 cm (D) 2.5 cm

Last Answer : (A) 0.5 cm

When having to squeeze past other people to get to your seat should you face them so your crotch is in their face or away from them so they get a face full of your butt?

Description : When having to squeeze past other people to get to your seat should you face them so your crotch is in their face or away from them so they get a face full of your butt?

Last Answer : answer:Good question. This happens regularly in theaters, airplanes, and so on. I've always presented my butt in these situations. I figured that 100% of all people have butts, while only 50% of people have ... that on a plane or in a theater, things are not going to be comfortable at all times.