For a base failure of a slope, depth factor (A) Df = 1(B) Df < 1 (C) Df > 1 (D) None of these

For a base failure of a slope, depth factor
(A) Df = 1
(B) Df < 1
(C) Df > 1
(D) None of these
by

1 Answer

Answer :

(C) Df > 1
by

Related questions

If the failure of a finite slope occurs through the toe, it is known as (A) Slope failure (B) Face failure (C) Base failure (D) Toe failure

Description : If the failure of a finite slope occurs through the toe, it is known as (A) Slope failure (B) Face failure (C) Base failure (D) Toe failure

Last Answer : (D) Toe failure

Failure of a slope occurs only when total shear force is A) Equal to total shearing strength (B) Greater than total shearing strength (C) Less than total shearing strength (D) None of these

Description : Failure of a slope occurs only when total shear force is A) Equal to total shearing strength (B) Greater than total shearing strength (C) Less than total shearing strength (D) None of these

Last Answer : Answer: Option B

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

The slope of isochrone at any point at a given time indicates the rate of change of(A) Effective stress with time (B) Effective stress with depth (C) Pore water pressure with depth (D) Pore water pressure with time

Description : The slope of isochrone at any point at a given time indicates the rate of change of (A) Effective stress with time (B) Effective stress with depth (C) Pore water pressure with depth (D) Pore water pressure with time

Last Answer : Answer: Option C

Coefficient of discharge of an ogee spillway (A) Depends on depth of approach and upstream slope (B) Depends on downstream apron interference and downstream submergence (C) Remains constant (D) Both (A) and (B

Description : Coefficient of discharge of an ogee spillway (A) Depends on depth of approach and upstream slope (B) Depends on downstream apron interference and downstream submergence (C) Remains constant (D) Both (A) and (B

Last Answer : Answer: Option D

According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Description : According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Last Answer : Answer: Option C

According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Description : According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water (F.S.D.) (B) Area of canal in cutting = BD + Sd 2 where B = bed width, d = depth of cutting and S is the side slope (C) If F.S.L. is above N.S.L the canal is called partly in cutting and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Description : Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water ... and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Last Answer : (D) All the above

In ΔABC and ΔDEF, AB = DE, AB || DE, BC = EF and BC || EF. Vertices A, B and C are joined to vertices D, E and F respectively (see Fig. 8.22). Show that (i) quadrilateral ABED is a parallelogram (ii) quadrilateral BEFC is a parallelogram (iii) AD || CF and AD = CF (iv) quadrilateral ACFD is a parallelogram (v) AC = DF (vi) ΔABC ≅ ΔDEF. -Maths 9th

Description : In ΔABC and ΔDEF, AB = DE, AB || DE, BC = EF and BC || EF. Vertices A, B and C are joined to vertices D, E and F respectively (see Fig. 8.22). Show that (i) quadrilateral ABED is a parallelogram ( ... CF and AD = CF (iv) quadrilateral ACFD is a parallelogram (v) AC = DF (vi) ΔABC ≅ ΔDEF. -Maths 9th

Last Answer : . Solution: (i) AB = DE and AB || DE (Given) Two opposite sides of a quadrilateral are equal and parallel to each other. Thus, quadrilateral ABED is a parallelogram (ii) Again BC = EF and BC || EF ... (Given) BC = EF (Given) AC = DF (Opposite sides of a parallelogram) , ΔABC ≅ ΔDEF [SSS congruency]

In figure, AB || DE, AB = DE, AC|| DF and AC = OF. Prove that BC || EF and BC = EF. -Maths 9th

Description : In figure, AB || DE, AB = DE, AC|| DF and AC = OF. Prove that BC || EF and BC = EF. -Maths 9th

Last Answer : Given In figure AB || DE and AC || DF, also AB = DE and AC = DF To prove BC ||EF and BC = EF Proof In quadrilateral ABED, AB||DE and AB = DE So, ABED is a parallelogram. AD || BE and AD = BE Now, ... = CF and BE||CF [from Eq. (iii)] So, BCFE is a parallelogram. BC = EF and BC|| EF . Hence proved.

In figure, AB || DE, AB = DE, AC|| DF and AC = OF. Prove that BC || EF and BC = EF. -Maths 9th

Description : In figure, AB || DE, AB = DE, AC|| DF and AC = OF. Prove that BC || EF and BC = EF. -Maths 9th

Last Answer : Given In figure AB || DE and AC || DF, also AB = DE and AC = DF To prove BC ||EF and BC = EF Proof In quadrilateral ABED, AB||DE and AB = DE So, ABED is a parallelogram. AD || BE and AD = BE Now, ... = CF and BE||CF [from Eq. (iii)] So, BCFE is a parallelogram. BC = EF and BC|| EF . Hence proved.

In Fig. 8.53,ABCD is a parallelogram and E is the mid - point of AD. A line through D, drawn parallel to EB, meets AB produced at F and BC at L.Prove that (i) AF = 2DC (ii) DF = 2DL -Maths 9th

Description : In Fig. 8.53,ABCD is a parallelogram and E is the mid - point of AD. A line through D, drawn parallel to EB, meets AB produced at F and BC at L.Prove that (i) AF = 2DC (ii) DF = 2DL -Maths 9th

Last Answer : Given, E is mid point of AD Also EB∥DF ⇒ B is mid point of AF [mid--point theorem] so, AF=2AB (1) Since, ABCD is a parallelogram, CD=AB ⇒AF=2CD AD∥BC⇒LB∥AD In ΔFDA ⇒LB∥AD ⇒LDLF​=ABFB​=1 from (1) ⇒LF=LD so, DF=2DL

Consider the following DataFrame df and answer questions. rollno name UT1 UT2 UT3 UT4 1 Prerna Singh 24 24 20 22 -Technology

Description : Consider the following DataFrame df and answer questions. rollno name UT1 UT2 UT3 UT4 1 Prerna Singh 24 24 20 22 -Technology

Last Answer : (i) (b)print(df.max())(ii) (a)df1=df[df[‘rollno’]==4]print(df1)(d)df1=df[df.rollno==4]print(df1)(iii)(a)both (i) and (ii)(iv)(d) both (i) and (ii)(v)(b)df [‘Grade’]=[’A’,’B’,’A’,’A’,’B’,’A’]

Mexico City, DF, Mexico?

Description : Mexico City, DF, Mexico?

Last Answer : Mexico City is the capital of Mexico and the largest city in theworld. Filled with vast historical markers and cutting edge modernarchitecture, this cultural melting pot where old meets new ... a natural wonder.Aside from glorious beauty and historical landmarks, Mexico Cityoffers every modern c

The treatment df for 3 factors each at 2 levels is

Description : The treatment df for 3 factors each at 2 levels is

Last Answer : Ans. 2 3 = 6-1 = 5

ECE Board Exam April 1997 Sound intensity is given as A. df/dP B. dE/dp C. dA/dP D. dP/dA

Description : ECE Board Exam April 1997 Sound intensity is given as A. df/dP B. dE/dp C. dA/dP D. dP/dA

Last Answer : D. dP/dA

Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Last Answer : (A) cos α = (dr + dp)/(dr + df)

In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Description : In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Last Answer : (A) Db 2 = K.Df

The reduction ratio for grinders is defined as (where, Df and Dp are average diameters of feed and product respectively). (A) Df /Dp (B) Dp /Df (C) Df - Dp (D) None of these

Description : The reduction ratio for grinders is defined as (where, Df and Dp are average diameters of feed and product respectively). (A) Df /Dp (B) Dp /Df (C) Df - Dp (D) None of these

Last Answer : (A) Df /Dp

In given figure, AD = 3 cm, AE = 5 cm, BD = 4 cm, CE = 4 cm, CF = 2 cm, BF = 2.5 cm, then (a) DE || BC (b) DF || AC (c) EF || AB (d) none of

Description : In given figure, AD = 3 cm, AE = 5 cm, BD = 4 cm, CE = 4 cm, CF = 2 cm, BF = 2.5 cm, then (a) DE || BC (b) DF || AC (c) EF || AB (d) none of

Last Answer : (c) EF || AB

Which of the following relationship is valid for the equilibrium position of the float in a Rotameter? (Where, Df= Drag force on the float Bf = Buoyant force on the float Wf = Weight of the float). (A) Df + Bf = Wf (B) Df = Bf + Wf (C) Df + Bf + Wf =0 (D) None of these

Description : Which of the following relationship is valid for the equilibrium position of the float in a Rotameter? (Where, Df= Drag force on the float Bf = Buoyant force on the float Wf = Weight of the float). (A) Df + Bf = Wf (B) Df = Bf + Wf (C) Df + Bf + Wf =0 (D) None of these

Last Answer : (A) Df + Bf = Wf

For an irreversible process involving only pressure-volume work (A) (dF)T, p <0 (B) (dF)T, p = 0 (C) (dF)T, p > 0 (D) (dA)T, v >0

Description : For an irreversible process involving only pressure-volume work (A) (dF)T, p 0 (D) (dA)T, v >0

Last Answer : (A) (dF)T, p

For a reversible process involving only pressure-volume work (A) (dF)T, p < 0 (B) (dF)T, p > 0 (C) (dF)T, p = 0 (D) (dA)T, v < 0

Description : For a reversible process involving only pressure-volume work (A) (dF)T, p < 0 (B) (dF)T, p > 0 (C) (dF)T, p = 0 (D) (dA)T, v < 0

Last Answer : (C) (dF)T, p = 0

State the use of OF and DF flags of 8086 microprocessor.

Description : State the use of OF and DF flags of 8086 microprocessor.

Last Answer : Overflow Flag: This flag is set if an overflow occurs, i.e. if the result of a signed operation is large enough to be accommodated in destination register. Direction Flag: It selects either increment or decrement mode for DI &/or SI register during string instructions.

If the cohesive force (c), is 1.5 t/m2 , the density ) of the soil is 2.0 t/m3 , factor of safety (F) is 1.5 and stability factor (Sn) is 0.05, the safe height of a slope, is (A) 5 metres (B) 8 metres (C) 10 metres (D) 12 metres

Description : If the cohesive force (c), is 1.5 t/m2 , the density ) of the soil is 2.0 t/m3 , factor of safety (F) is 1.5 and stability factor (Sn) is 0.05, the safe height of a slope, is (A) 5 metres (B) 8 metres (C) 10 metres (D) 12 metres

Last Answer : (C) 10 metres

Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The rolling resistance of the road will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Description : A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The ... will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Last Answer : (C) 40 kg/tonne

Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) The net amount of water which joins the surface streams in a catchment, is known as surface run-off (B) The amount of water which joins the stream from the underground water, is called base flow (C) The yearly run off in cm depth over the catchment, is termed as the yield of the drainage basin(D) None of these

Description : Pick up the incorrect statement from the following:  (A) The net amount of water which joins the surface streams in a catchment, is known as  surface run-off  (B) The amount of water which ... over the catchment, is termed as the yield of the drainage  basin  (D) None of these

Last Answer : (D) None of these

A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Description : A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Last Answer : (A) 3S/bh

Hydrodynamic pressure due to earthquake acts at a height of (A) 3H/4 above the base (B) 3H/4 below the water surface (C) 4H/3 above the base (D) 4H below the water surface, where H is the depth of water.

Description : Hydrodynamic pressure due to earthquake acts at a height of (A) 3H/4 above the base (B) 3H/4 below the water surface (C) 4H/3 above the base (D) 4H below the water surface, where H is the depth of water.

Last Answer : Answer: Option C

Grillage foundation (A) Is used to transfer heavy structural loads from steel columns to a soil having low bearing capacity (B) Is light and economical (C) Does not require deep cutting as the required base area with required pressure intensity is obtained at a shallow depth (D) All the above

Description : Grillage foundation (A) Is used to transfer heavy structural loads from steel columns to a soil having low bearing capacity (B) Is light and economical (C) Does not require deep cutting as the required base area with required pressure intensity is obtained at a shallow depth (D) All the above

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) The width of the wall is constructed thicker at the base in a stepped fashion (B) A long vertical load transferring concrete structure is called a concrete pile (C) In pile which transfers the load to the soil by the friction between the pile and the surrounding soil is called friction pile (D) The pile which transfers the load to a hard rock bed at certain depth is called load bearing

Description : Pick up the incorrect statement from the following: (A) The width of the wall is constructed thicker at the base in a stepped fashion (B) A long vertical load transferring concrete structure is ... ) The pile which transfers the load to a hard rock bed at certain depth is called load bearing

Last Answer : Answer: Option D

Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Description : Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Last Answer : Answer: Option C

weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Description : weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Last Answer : ANS: A

If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Description : If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of (A) 2 (B) 1/2 (C) 8 (D) 1/8

Last Answer : (D) 1/8

A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 , the area of steel required, is (A) 14 cm(B) 15 cm2(C) 16 cm2(D) 17 cm

Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm

Last Answer : Answer: Option C

The main factor which affects the infiltration capacity, is (A) Thickness of saturated layer (B) Depth of surface detention (C) Soil moisture (D) All the above

Description : The main factor which affects the infiltration capacity, is (A) Thickness of saturated layer (B) Depth of surface detention (C) Soil moisture (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) When water table is above the base of a footing, the dry weight m should be used for soil below water table (B) When water table is located somewhat below the base of a footing, the elastic wedge is partly of moist soil and partly of submerged soil, and a suitable reduction factor is used (C) When water table is just at the base of the footing, no reduction factor is used (D) None of these

Description : Pick up the correct statement from the following: (A) When water table is above the base of a footing, the dry weight m should be used for soil below water table (B) When water table is located ... water table is just at the base of the footing, no reduction factor is used (D) None of these

Last Answer : (B) When water table is located somewhat below the base of a footing, the elastic wedge is partly of moist soil and partly of submerged soil, and a suitable reduction factor is used

‘L/mG’ is the expression for (A) Absorption factor (B) Brinkman number (C) Slope of operating line in absorber (D) Slope of operating line in stripper

Description : ‘L/mG’ is the expression for (A) Absorption factor (B) Brinkman number (C) Slope of operating line in absorber (D) Slope of operating line in stripper

Last Answer : (A) Absorption factor

. The absorption factor is defined as (where, L = liquid flow rate, G = gas flow rate and, m = slope of the equilibrium line). (A) L/mG (B) G/mL (C) mL/G (D) LG/m

Description : . The absorption factor is defined as (where, L = liquid flow rate, G = gas flow rate and, m = slope of the equilibrium line). (A) L/mG (B) G/mL (C) mL/G (D) LG/m

Last Answer : (A) L/mG

Following the six-tenth factor rule, if a log-log plot of capacity of the equipment vs. cost of the equipment is made, then a straight line is obtained, whose slope is equal to (A) 0.1 (B) 0.6 (C) 0.2 (D) 0.8

Description : Following the six-tenth factor rule, if a log-log plot of capacity of the equipment vs. cost of the equipment is made, then a straight line is obtained, whose slope is equal to (A) 0.1 (B) 0.6 (C) 0.2 (D) 0.8

Last Answer : (B) 0.6

Which one of the following is not an internal factor affects in slope processes? (A) Lithology of the materials on the slope (B) Ground water or rain water (run off) (C) Geological Structures (D) Earthquakes (Tectonic activity)

Description : Which one of the following is not an internal factor affects in slope processes? (A) Lithology of the materials on the slope (B) Ground water or rain water (run off) (C) Geological Structures (D) Earthquakes (Tectonic activity)

Last Answer : (D) Earthquakes (Tectonic activity) 

According to traditional approach the factor responsible for operation of downward slope of demand curve are (a) Change in number of consumers ; (b) Law of decreasing marginal utility (c) Alternative uses of goods ; (d) All the three

Description : According to traditional approach the factor responsible for operation of downward slope of demand curve are (a) Change in number of consumers ; (b) Law of decreasing marginal utility (c) Alternative uses of goods ; (d) All the three

Last Answer : (d) All the three

A young child presents with respiratory distress, worsening over 2 days. Blood gases show a pH of 7.25, a PCO2 of 7.5kPa, a PO2 of 8.5kPa, and a base excess of -4. Which of the following interpretations is correct? 1) Results are consistent with bronchopulmonary dysplasia. 2) Blood gases suggest type 1 respiratory failure. 3) Immediate intubation is required. 4) Results are consistent with late severe asthma. 5) Bicarbonate may be necessary to correct the acidosis.

Description : A young child presents with respiratory distress, worsening over 2 days. Blood gases show a pH of 7.25, a PCO2 of 7.5kPa, a PO2 of 8.5kPa, and a base excess of -4. Which of the ... required. 4) Results are consistent with late severe asthma. 5) Bicarbonate may be necessary to correct the acidosis.

Last Answer : Answers-4 In interpreting blood gas results, the following sequence may be useful: Inspect the pH: Is it low, normal or high? Inspect the CO2: Is it low, normal or high? Inspect the PO2: Is ... excess and normal pH. Bicarbonate is usually only considered if the base deficit exceeds about -8 or 00.

Misstatements must be compared to some measurement base before a decision can be made about the materiality of the failure to follow GAAP. A commonly accepted measurement base would be a. Net income. b. Total assets. c. Working capital. d. All of the above.

Description : Misstatements must be compared to some measurement base before a decision can be made about the materiality of the failure to follow GAAP. A commonly accepted measurement base would be a. Net income. b. Total assets. c. Working capital. d. All of the above.

Last Answer : All of the above.

A cylindrical vessel can hold 154 g of water. If the radius of its base is 3.5 cm, and 1 cm3 of water weighs lg,find the depth of water. -Maths 9th

Description : A cylindrical vessel can hold 154 g of water. If the radius of its base is 3.5 cm, and 1 cm3 of water weighs lg,find the depth of water. -Maths 9th

Last Answer : Since 1 cm3 of water weighs 1 g. ∴ Volume of cyclinder vessel = 154 cm3 πr2h = 154 h = 154 × 7 / 22 × 3.5 × 3.5 h ;= 4 cm Hence, the depth of water is 4 cm.

A cylindrical vessel can hold 154 g of water. If the radius of its base is 3.5 cm, and 1 cm3 of water weighs lg,find the depth of water. -Maths 9th

Description : A cylindrical vessel can hold 154 g of water. If the radius of its base is 3.5 cm, and 1 cm3 of water weighs lg,find the depth of water. -Maths 9th

Last Answer : Since 1 cm3 of water weighs 1 g. ∴ Volume of cyclinder vessel = 154 cm3 πr2h = 154 h = 154 × 7 / 22 × 3.5 × 3.5 h ;= 4 cm Hence, the depth of water is 4 cm.

The wall of a dam is broader at the base (1) because streamlining is required (2) to withstand pressure that increases with depth (3) to withstand pressure that increases in a horizontal plane (4) to withstand pressure that is increased with atmospheric pressure

Description : The wall of a dam is broader at the base (1) because streamlining is required (2) to withstand pressure that increases with depth (3) to withstand pressure that increases in a horizontal plane (4) to withstand pressure that is increased with atmospheric pressure

Last Answer : (2) to withstand pressure that increases with depth Explanation: Darns are built broader at the base for two reasons. The first is because it needs to be stable enough to support the dam, and two, ... the structure the lower levels of water are at higher pressure than the upper levels of the water.

The wall of a dam is broader at the base (1) because streamlining is required (2) to withstand pressure that increases with depth (3) to withstand pressure that increases in a horizontal plane (4) to withstand pressure that is increased with atmospheric pressure

Description : The wall of a dam is broader at the base (1) because streamlining is required (2) to withstand pressure that increases with depth (3) to withstand pressure that increases in a horizontal plane (4) to withstand pressure that is increased with atmospheric pressure

Last Answer : (2) to withstand pressure that increases with depth Explanation: Darns are built broader at the base for two reasons. The first is because it needs to be stable enough to support the dam, and two, ... the structure the lower levels of water are at higher pressure than the upper levels of the water.