Explain the following energy conservation techniques: (i) By reducing I2R losses in Trans. system (ii) By optimizing distribution voltage.

Explain the following energy conservation techniques: (i) By reducing I2R losses in Trans. system (ii) By optimizing distribution voltage.
by

1 Answer

Answer :

i) By reducing I2R losses in Trans: 

1. Opting for low resistance All Aluminum Alloy conductors (AAAC) in place of conventional aluminum cored steel reinforced (ACSR) lines. 2. Increasing the system voltage leads to reduction in the line current transmitted that leads to lower I2R losses. 3. Using relevantly suitable means to reduce the line currents to lowest possible values by maintaining the power factor near unity ( reactive power control, power factor improvement) 4. Use of voltage controllers to maintain the voltage level at rated levels (not allowing the voltage to fall that leads to higher line currents) 5. Marinating proper distance (as low as economically possible) between consumer and distribution transformer.


(ii) By optimizing distribution voltage: 

Optimization of system voltage is maintaining the voltage of the system at the rated/specified level such that the related load requirements are most satisfactorily fulfilled and at the same time the losses/abnormal conditions related to over voltages/ under voltages are eliminated/reduced. There is fall in efficiency and quality of output with both these adverse/abnormal voltage conditions. For example; High voltages to resistance loads such as ovens etc. lead to excessive currents that create unnecessary heating leading to power losses in the supply lines and load. Also over voltages to motors leads to higher iron losses and higher torque that is not needed. Hence these are to be avoided. Under voltages to motors leads to excessive currents being drawn to take up the load resulting in higher supply line power losses. Thus maintaining the voltages at the specified levels leads to energy savings/conservation.

by

Related questions

Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

Description : Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

Last Answer : (i) Balancing Phase currents: Proper (healthy balanced) three phase loads always draw equal currents in all lines but single phase loads in the 3 phase 4 wire system or loads connected between two ... . 11) Minimize I2R losses. 12) Balance the load currents. 13) Regulate the system voltages.

Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses.

Description : Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses. 

Last Answer : Energy conservation techniques to reduce commercial losses:  1. Mitigation of Power Theft: Power theft being the most important issue which all of the service providing utilities ... agricultural sector. Prepaid meters may prove effective measures against unauthorized abstraction of energy. 

List out energy conservation techniques to be adopted to reduce losses in the induction motor.

Description : List out energy conservation techniques to be adopted to reduce losses in the induction motor.

Last Answer : Following are the list of energy conservation techniques in electrical motors:  1) Reduction in iron losses by using low loss silicon steel core material laminated to thinner dimension. 2) Using bigger ... balancing. 11) By improving power quality. 12) Operating motor in star mode at light load.

Suggest the energy conservation techniques in following cases : (i) Motor is running with 70% loaded condition. (ii) Motor is continuously loaded at 50%. (iii) Motor runs with 30% loaded condition but sometimes rises to 50% loading condition. (iv) Motor runs continuously under no-load condition.

Description : Suggest the energy conservation techniques in following cases : (i) Motor is running with 70% loaded condition. (ii) Motor is continuously loaded at 50%. (iii) Motor runs with 30% loaded condition but sometimes rises to 50% loading condition. (iv) Motor runs continuously under no-load condition.

Last Answer : Following are the suggestion the energy conservation techniques in following cases :  (i) Motor is running with 70% loaded condition: Use APFC or IPFC for better power factor improvement. Use ... If possible use low capacity motor for above condition. If possible switch off the motor.

Explain any two energy conservation techniques in fan.

Description : Explain any two energy conservation techniques in fan.

Last Answer : Following are energy conservation techniques in Fans : 1) Use the electronic regulators instead of conventional regulator: Function of regulator is to control the speed of the fan. The conventional regulators ... 't forget to properly maintain your electric fan and keep it in good working order. 

Explain how technical losses can be reduced by use of energy efficient transformer in Transmission and Distribution system.

Description : Explain how technical losses can be reduced by use of energy efficient transformer in Transmission and Distribution system.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

List out the energy conservation techniques in Fans.

Description : List out the energy conservation techniques in Fans.

Last Answer : Following are energy conservation techniques in Fans : Use the electronic regulators instead of conventional regulator. The fan used at low speed instead of high speed. Adjust the direction of the ceiling ... Day / 1000 = Daily Kilowatt-hour (kWh) Consumption (1 kilowatt [kw] = 1000 watts)

Why energy conservation techniques should be adopted in transformers even though its efficiency is 90%?

Description : Why energy conservation techniques should be adopted in transformers even though its efficiency is 90%? 

Last Answer : Reason for energy conservation techniques should be adopted in transformers even though its efficiency is 90% : Transformer performance depends on its efficiency. Transformers used in real-time ... improve the efficiency of the transformer more than 90% as there are no mechanical losses.

State the opportunities for energy conservation techniques in transformers.

Description : State the opportunities for energy conservation techniques in transformers.

Last Answer : Opportunities for energy conservation techniques in transformers: Most of the energy loss that occurs in transformer is due to heat or vibration in the core that also reduces life of ... 9. Use better quality insulation materials to improve overload capacity and decrease dielectric leakages. 

With neat diagram explain use of “reactive power controller” to reduce technical losses in transmission and distribution system.

Description : With neat diagram explain use of “reactive power controller” to reduce technical losses in transmission and distribution system.

Last Answer : Reactive power compensation in Transmission and Distribution systems: The reactive power is present in lines due to the reactive loads and device/ component reactance. This leads to heavy currents for active ... switched to the line as per the requirement of lagging or leading reactive VA. 

State and explain any four commercial losses in transmission and distribution system.

Description : State and explain any four commercial losses in transmission and distribution system.

Last Answer : Skin effects Carvana effect  Core loss  Over current 

Explain scenario of transmission and distribution losses at national level.

Description : Explain scenario of transmission and distribution losses at national level.

Last Answer : Scenario of transmission and distribution losses at national level: i) T & D losses in India are the highest in the world. Inadequate investment in T&D network is one of the main reasons ... . According to planning commission report, the target is to minimize these losses to 18% upto 2018.

State and explain any four technical losses in transmission and distribution systems.

Last Answer : Technical losses: i) Copper losses ii) Unbalance loading iii) Long length of distribution lines iv) Conductor of inadequate size v) Various losses in transformer vi) Long distance between transformer and ... be the season behind this which is due to less interest of the line men in their work.

State the losses in secondary distribution system.

Description : State the losses in secondary distribution system. 

Last Answer : The losses in secondary distribution system: a) Technical losses: 1. Due to poor voltage 2. Due to unbalance load 3. Due poor quality of transformer & its components 4. Due to poor quality ... of induction type of energy meter. 3. Lack of administration. 4. Energy theft 5. Unmetered supply

List out the different technical losses that takes place in Transmission and Distribution system.

Description : List out the different technical losses that takes place in Transmission and Distribution system.

Last Answer : Different technical losses that takes place in Transmission and Distribution system: 1) Losses due to random growth of sub transmission &distribution system. planned growth/expansion maintains ... unsatisfactory reactive power compensation. 6) Losses due to poor quality of equipment used. 

Losses caused by skin effect and the I2R (power) loss are classified as what type of loss?

Description : Losses caused by skin effect and the I2R (power) loss are classified as what type of loss?

Last Answer : Copper losses.

72 Harmonics in transformer result in A. Increased core losses B. Increased I2R losses C. Magnetic interference with communication circuits D. All of the above

Description : 72 Harmonics in transformer result in A. Increased core losses B. Increased I2R losses C. Magnetic interference with communication circuits D. All of the above

Last Answer : D. All of the above

State commercial losses in transmission and distribution systems. Also state the remedies for the same.

Description : State commercial losses in transmission and distribution systems. Also state the remedies for the same.

Last Answer : Following are the commercial losses in Transmission Distribution systems: 1) Make unauthorized extension of loads. ( Direct Hooking) 2) Errors in meter reading & recording (faulty meter). 3) By ... turn reduces the energy requirements by some scale in turn leading to saving in energy sources.

Describe the following energy conservation methods of lighting system. i) By replacing lamp sources ii) Using light control gears.

Description : Describe the following energy conservation methods of lighting system. i) By replacing lamp sources ii) Using light control gears.

Last Answer : Energy conservation methods of lighting system:  i) By replacing lamp sources:  Installation of energy efficient fluorescent lamps in place of Conventional fluorescent lamps. Installation of ... (HF) electronic ballasts in place of conventional ballasts which saves energy up to 35%.

Describe the following energy conservation methods of electrical motor. i) By motor survey ii) By matching loads with motor rating

Description : Describe the following energy conservation methods of electrical motor. i) By motor survey ii) By matching loads with motor rating

Last Answer : Energy conservation methods of electrical motor:  1) By Motor Survey: Large industries have a massive population of LT motors. Load survey of LT motors can be taken-up methodically to ... -speed motors, eddy-current couplings, fluid couplings, and solid-state electronic variable speed drives.

Which of the following techniques can be used for optimizing backed up data space? a) Encryption and Deduplication b) Compression and Deduplication c) Authentication and Deduplication d) Deduplication only

Description : Which of the following techniques can be used for optimizing backed up data space? a) Encryption and Deduplication b) Compression and Deduplication c) Authentication and Deduplication d) Deduplication only

Last Answer : Compression and Deduplication

Which of the following techniques can be used for optimizing backed up data space? a) Encryption and Deduplication b) Compression and Deduplication c) Authentication and Deduplication d) Deduplication only

Description : Which of the following techniques can be used for optimizing backed up data space? a) Encryption and Deduplication b) Compression and Deduplication c) Authentication and Deduplication d) Deduplication only

Last Answer : Compression and Deduplication

With example explain how the replacement of lamps in lighting system contributes for energy conservation?

Description : With example explain how the replacement of lamps in lighting system contributes for energy conservation?

Last Answer : Replacement of lamps in lighting system contributes for energy conservation: i. Replacing incandescent lamps by Compact Fluorescent Lamps (CFL's) ii. Replacing conventional fluorescent lamp by energy efficient fluorescent ... lights in place of all other lamps above as feasible (in terms of cost) 

Explain the role of adequate maintenance of lighting system in energy conservation.

Description : Explain the role of adequate maintenance of lighting system in energy conservation.

Last Answer : Role of adequate maintenance of lighting system in energy conservation: Illumination level reduces due to accumulation of dirt on lamps and luminaries. Further as the lamps get older their ... should be conducted to take advantage of energy conservation opportunities as user requirements change.

Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

Description : Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

Last Answer : Energy conservation techniques by installation of separate transformer / servo stabilizer: The luminous efficiency of lamps depends upon the voltage applied across the terminals. It gives its best ... the voltage constant in that installation for giving best luminous efficiency of lamps.

Explain parallel operation of transformer in context of energy conservation.

Description : Explain parallel operation of transformer in context of energy conservation.

Last Answer : Parallel operation of the transformer in context of energy conservation: The transformers operate near their maximum efficiency around 70 % to 100 % of their rated loads. For huge establishments drawing highly ... thus saving its low load losses. This is done as per the requirements of the loads.

Explain energy conservation technique in induction motor by improving mechanical power and transmission efficiency.

Description : Explain energy conservation technique in induction motor by improving mechanical power and transmission efficiency.

Last Answer : Energy Conservation Technique in Induction Motor: To improve the mechanical power and transmission efficiency, proper selection of belt drives and gear drives suitable for particular application is ... . Energy conservation is achieved by using more efficient gears for particular applications. 

Explain the following Energy conservation methods of electrical motor : (a) Rewinding of motors (b) Operating in star mode

Description : Explain the following Energy conservation methods of electrical motor : (a) Rewinding of motors (b) Operating in star mode

Last Answer : Energy conservation methods of an electric motor:  (a) Rewinding of motors: i) During rewinding by preserving the original winding characteristics (material quality, design and structure). It is ... in the lines also reduces leading to lower copper losses in motor and decrease line losses.

Explain the need of energy conservation in present scenario.

Description : Explain the need of energy conservation in present scenario.

Last Answer : Need of energy conservation in present scenario: 1. Fossil fuels like coal, oil which have taken no. of years to form and now they are on the verge of depleting soon. 2. In last ... protection and integrated economic and social development. 9. Energy saved is as good as energy generated. 

Draw block diagram of microprocessor based centrallized control equipment of energy conservation and explain it.

Description : Draw block diagram of microprocessor based centrallized control equipment of energy conservation and explain it.

Last Answer : Microprocessor based centralized control equipment of energy conservation: The sensors are employed to get the values/levels of quantities to be controlled like intensity of light, speed of machine ... using the RAM. The requisite signals are given to the control gear for controlling loads. 

Explain energy conservation technique in induction motor by minimizing idle and redundant running of motor.

Last Answer : Energy conservation technique in induction motor by minimizing idle and redundant running of motor: 1) Loss of energy as the no load power drawn is approximately about 12% to 16% of rated ... to unnecessary line losses. 4) Reduction in overall system energy efficiency over period of time.

Explain energy conservation technique “by improving power quality” for induction motor.

Description : Explain energy conservation technique “by improving power quality” for induction motor.

Last Answer : Energy conservation method in induction motor by improving power quality: Electrical energy can be conserved by improving the power quality. It can be achieved by avoiding voltage unbalance, maintaining ... losses can be minimized by using harmonic filter thus reducing the harmonics in the system.

List out the energy conservation equipments related to • Lighting system • Induction motor

Description : List out the energy conservation equipments related to • Lighting system • Induction motor

Last Answer : Energy conservation equipments related to:  1. Lighting System:  1. Luxmeter 2. Power Analyzer 3. Voltage Stabilizer 4. Electronic Ballast 5. LED Lamp 6. Control gear or Regulators 7. ... 2. Power Analyzer 3. Digital Voltmeter 4. Digital Ammeter 5. Wattmeter 6. Different types of starter

State the difference between energy conservation and energy audit.

Description : State the difference between energy conservation and energy audit. 

Last Answer : energy conservation Energy audit It is reducing the growth of energy consumption by avoiding unnecessary usage of energy It is an inspection, survey & analysis of energy flows ... Various measuring instruments, with proper sensing elements are required for the energy audit. 

List the energy conservation technique in induction motor.

Description : List the energy conservation technique in induction motor. 

Last Answer : Following are the list of energy conservation techniques in electrical motors: 1) Reduction in iron losses by using low loss silicon steel core material laminated to thinner dimension. 2) Using bigger length ... at light load. 13) By rewinding in induction motor 14) By motor survey

Define Energy conservation.

Description : Define Energy conservation. 

Last Answer : Energy conservation:  Reduction in the amount of energy consumed in a process or system, or by an organization or society, through economy, elimination of waste, and rational use is referred ... electrical power and to increase the efficiency of every machine and material by minimizing the losses.

State how 'parallel operation of transformers' helps in energy conservation.

Description : State how 'parallel operation of transformers' helps in energy conservation.

Last Answer : 'Parallel operation of transformers' helps in energy conservation: The transformers operate near their maximum efficiency at around 70 % to 100 % of their rated loads. For a huge load system drawing highly ... if of higher rating may be put in service while the first one may be switched off.

State salient features of Energy conservation Act-2003

Description : State salient features of Energy conservation Act-2003

Last Answer : Salient features of Energy Conservation Act-2003: i) The Central Government to prepare a National Electricity Policy in consultation with State Governments. ii) Thrust to complete the rural ... to undertake generation and generating companies would be free to take up distribution businesses.

Discuss how power factor tariff results into energy conservation.

Description : Discuss how power factor tariff results into energy conservation.

Last Answer : Power factor tariff results into energy conservation: i) Applying incentives and penalties according to power factor is an effective way, which enables consumer to improve power factor so that he can ... finally leads to reduction in the current drawn by the load and helps for energy conservation.

Discuss the role of replacement of old lamps by new more energy efficient lamps in the conservation of energy.

Description : Discuss the role of replacement of old lamps by new more energy efficient lamps in the conservation of energy.

Last Answer : Role of replacement of old lamps by new more energy efficient lamps in the conservation of energy: i) Replacing incandescent lamps by Compact Fluorescent lamps: High wattage incandescent lamps are ... lamps of same luminous output. By these replacements, much more energy can be conserved.

What is Time of Day tariff? How it help in energy conservation?

Description : What is Time of Day tariff? How it help in energy conservation?

Last Answer : Time-off-day tariff:- In addition to basic tariff (Maximum Demand Tariff / KVA Maximum Demand Tariff / Load factor tariff /also the tariff in which P.F. of industrial consumer is taken ... the rated load for longer times of the day their overall efficiency gets higher helping to conserve energy.

State any four periodical maintenance which is necessary in transformer to achieve energy conservation.

Description : State any four periodical maintenance which is necessary in transformer to achieve energy conservation.

Last Answer : Periodical maintenance necessary in transformer to achieve energy conservation: Proper periodical maintenance leads in Energy conservation 1) Check Voltage, current, temperature and other parameters. 2) ... breather and silica gel. 5) Check cooling arrangement. 6) Check Insulation resistance.

State the need of energy conservation in transformer.

Description : State the need of energy conservation in transformer. 

Last Answer : Need of energy conservation in transformer: In electrical power system, transformers are used to change the voltage levels of different sections as per the need of economic and efficient operation of ... for some other good reason. Therefore, there is need of energy conservation in transformer.

State the need of energy conservation in electrical motor.

Description : State the need of energy conservation in electrical motor.

Last Answer : Need of energy conservation in Electrical motors: 1. Induction motors are used as electrical drives in industrial, commercial and residential sectors. 2. Considering all industrial applications, 70% of ... system. 8. To adopt advanced technology in design and to use better quality materials.

Explain reactive power compensation in Transmission and Distribution systems.

Description : Explain reactive power compensation in Transmission and Distribution systems.

Last Answer : Reactive power compensation in Transmission and Distribution systems: The reactive power is present in lines due to the reactive loads and device/ component reactances. This leads to heavy ... Diagram shows a scheme of reactive power compensation used in transmission and distribution systems. 

Which mode of transportation reduces trans-shipment losses and delays ? -SST 10th

Description : Which mode of transportation reduces trans-shipment losses and delays ? -SST 10th

Last Answer : C - The pipeline mode is used for transporting liquids and gases. It effectively reduces the costs and the deklays.

Line losses in a distribution circuit are kept to a minimum by __________. A. adding rubber insulation conductors to the circuit B. using higher current and lower voltage C. increasing the number of thermal relays in the circuit D. using higher voltage and lower current

Description : Line losses in a distribution circuit are kept to a minimum by __________. A. adding rubber insulation conductors to the circuit B. using higher current and lower voltage C. increasing the number of thermal relays in the circuit D. using higher voltage and lower current

Last Answer : Answer: D

State the working principle and operation of Automatic power factor controller used in Transmission and Distribution system.

Description : State the working principle and operation of Automatic power factor controller used in Transmission and Distribution system.

Last Answer : Diagram of Automatic over factor controller Automatic Power factor control: The pf controller is used to maintain the pf at unity across the lines it is connected. Maintaining the pf at ... the load demand in the system is increased. 8. Check if power transformer compensation is provided.

Indicate the three types oftransmissionline energylosses. a. I2R, R , and temperature b. Radiation, I2R, and dielectric heating c. Dielectric separation, insulation breakdown, and radiation d. Conductor heating, dielectric heating, and radiation resistance.

Description : Indicate the three types oftransmissionline energylosses. a. I2R, R , and temperature b. Radiation, I2R, and dielectric heating c. Dielectric separation, insulation breakdown, and radiation d. Conductor heating, dielectric heating, and radiation resistance.

Last Answer : b. Radiation, I2R, and dielectric heating

Define with respect to FET:- (i) Static drain resistance (ii) Dynamic resistance (iii) Trans conductance (iv) Pinch-off voltage

Description : Define with respect to FET:- (i) Static drain resistance (ii) Dynamic resistance (iii) Trans conductance (iv) Pinch-off voltage

Last Answer : (i) Static drain resistance- It is the ratio of drain source voltage (ΔVDS) to the drain current (ID) at constant gate-source voltage. It can be expressed as, Rd = (VDS)/(ID) at ... of charge carrier and the value of drain current reaches its constant saturation value is called pinch off voltage.