State advantages of electronic ballast compare to electrical ballast.

State advantages of electronic ballast compare to electrical ballast.
by

1 Answer

Answer :

advantages of electronic ballast compare to electrical ballast: 1. Instant light 2. Lighter in weight 3. power saving is up to 35% 4. Heat output is negligible, that reduces load on air conditioning. 5. Improved power factor 6. Operates at low voltage 7. Enhances life of lamp

by

Related questions

State the need of energy conservation in electrical motor.

Description : State the need of energy conservation in electrical motor.

Last Answer : Need of energy conservation in Electrical motors: 1. Induction motors are used as electrical drives in industrial, commercial and residential sectors. 2. Considering all industrial applications, 70% of ... system. 8. To adopt advanced technology in design and to use better quality materials.

State the advantages of cogeneration.

Description : State the advantages of cogeneration. 

Last Answer : Advantages of co-generation: 1) Co-generation can meet both power & heat requirements. 2) Less cost than conventional generation. 3) Higher system efficiency due to energy wastage is highly ... reduces due to cogeneration plant is located in same premises. 10) It can maintain grid stability 

State the advantages of adoption of cogeneration system in an industry.

Description : State the advantages of adoption of cogeneration system in an industry.

Last Answer : The advantages of adoption of cogeneration system in an industry: 1) Co-generation can meet both power & heat needs. 2) Less costly. 3) Very high efficiency. 4) Reduction in ... . 8) Due to decentralization of electricity it avoids transmission losses & makes system more efficient.

State any four advantages of soft starter.

Description : State any four advantages of soft starter.

Last Answer : Advantages of soft starter: 1. Very low line voltage drops on motor operation 2. Reduced energy losses in the lines 3. System efficiency increases 4. Very smooth starting & operation 5. As ... may lead to lower MD billing. 13. Less mechanical maintenance. 14. Saving in operating costs.

List out the factors to be considered to select electrical drives for an application.

Description : List out the factors to be considered to select electrical drives for an application.

Last Answer : Following are the factors to be considered to select electrical drives for an application:  1) Load torque required at normal speed matches with available torque of motor. 2) Break down torque ... selecting an energy efficient motor the cost benefit analysis over the long run must be worked out.

Explain the following Energy conservation methods of electrical motor : (a) Rewinding of motors (b) Operating in star mode

Description : Explain the following Energy conservation methods of electrical motor : (a) Rewinding of motors (b) Operating in star mode

Last Answer : Energy conservation methods of an electric motor:  (a) Rewinding of motors: i) During rewinding by preserving the original winding characteristics (material quality, design and structure). It is ... in the lines also reduces leading to lower copper losses in motor and decrease line losses.

Describe the following energy conservation methods of electrical motor. i) By motor survey ii) By matching loads with motor rating

Description : Describe the following energy conservation methods of electrical motor. i) By motor survey ii) By matching loads with motor rating

Last Answer : Energy conservation methods of electrical motor:  1) By Motor Survey: Large industries have a massive population of LT motors. Load survey of LT motors can be taken-up methodically to ... -speed motors, eddy-current couplings, fluid couplings, and solid-state electronic variable speed drives.

Explain any four advantages of amorphous transformer.

Description : Explain any four advantages of amorphous transformer.

Last Answer : Advantages of amorphous core transformer: 1) Lowest hysteresis loss. 2) Low eddy current loss. 3) Low temperature rise. 4) Up to 75% energy saving using amorphous metal than conventional metal. 5 ... capacity. 9) High Reliability. 10) Excellent short circuit capacity. 11) Less maintenance cost. 

replace florescent ballast

Description : replace florescent ballast

Last Answer : Need Answer

Sand may be used as ballast for A. Wooden sleeper B. Cast iron sleeper C. Steel sleeper D. None of These

Description : Sand may be used as ballast for A. Wooden sleeper B. Cast iron sleeper C. Steel sleeper D. None of These

Last Answer : B [Cast iron sleeper]

Best ballast contains stones varying in size from A. 1 to 4 cm B. 1.5 to 4.5 cm C. 2 to 5 cm D. 3 to 6 cm

Description : Best ballast contains stones varying in size from A. 1 to 4 cm B. 1.5 to 4.5 cm C. 2 to 5 cm D. 3 to 6 cm

Last Answer : C [2 to 5 cm]

Boxing of ballast is done A. Under the rail B. At the rail C. In between two rail D. In between two sleeper

Description : Boxing of ballast is done A. Under the rail B. At the rail C. In between two rail D. In between two sleeper

Last Answer : B [At the rail]

Minimum depth of ballast prescribed of Broad Gauge trunk lines of Indian Railways, is A. 20 cm B. 25 cm C. 30 cm D. 35 cm

Description : Minimum depth of ballast prescribed of Broad Gauge trunk lines of Indian Railways, is A. 20 cm B. 25 cm C. 30 cm D. 35 cm

Last Answer : B [25 cm]

When a fluorescent lamp fails to light, the trouble can be in the _____________. A. lamp B. starter C. ballast D. all of the above

Description : When a fluorescent lamp fails to light, the trouble can be in the _____________. A. lamp B. starter C. ballast D. all of the above

Last Answer : Answer: D

When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, causing glass to fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Description : When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, ... fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Last Answer : Answer: D

Which of the following components are used to assemble a fluorescent lighting system? A. Lamp B. Starter C. Ballast D. All of the above

Description : Which of the following components are used to assemble a fluorescent lighting system? A. Lamp B. Starter C. Ballast D. All of the above

Last Answer : Answer: D

Which component of the circuit shown in the illustration is the ballast? EL-0081 A. A B. B C. C D. D

Description : Which component of the circuit shown in the illustration is the ballast? EL-0081 A. A B. B C. C D. D

Last Answer : Answer: A

The device shown in the illustration is a/an ____________. EL-0083 A. noise filtering choke B. autotransformer C. fluorescent light ballast D. power factor correction inductor

Description : The device shown in the illustration is a/an ____________. EL-0083 A. noise filtering choke B. autotransformer C. fluorescent light ballast D. power factor correction inductor

Last Answer : Answer: B

How does ballast-less track provide safe travel?

Description : How does ballast-less track provide safe travel?

Last Answer : ANSWER I: Ballast is a prime component of the track that acts as a vibrant medium to transmit from the rail surface the weight of the train down to the formation, the wells set on ... cost involved in laying a ballast-less track is more initially but it requires less recurring maintenance cost.

__________ circuit is most commonly used to measure strain with the help of a strain gauge. (A) Ballast (B) Voltage balancing potentiometric (C) Simple current sensitive (D) None of these

Description : __________ circuit is most commonly used to measure strain with the help of a strain gauge. (A) Ballast (B) Voltage balancing potentiometric (C) Simple current sensitive (D) None of these

Last Answer : Option B

The stones obtained by blasting are used as (A) Ballast in railways (B) Aggregates for concrete (C) Road metal (D) All the above

Description : The stones obtained by blasting are used as (A) Ballast in railways (B) Aggregates for concrete (C) Road metal (D) All the above

Last Answer : Answer: Option D

On which Following products is labelling not Voluntary a) Colour TV c) Ceiling fans b) Ballast d) Induction motors

Description : On which Following products is labelling not Voluntary a) Colour TV c) Ceiling fans b) Ballast d) Induction motors

Last Answer : Colour TV

Product on which labelling is mandatory..... iii. Electric Geysers. B) LPG Stoves iv. Ballast. D) Colour TV

Description : Product on which labelling is mandatory..... iii. Electric Geysers. B) LPG Stoves iv. Ballast. D) Colour TV

Last Answer : COLOUR TV

On which Product is Labeling mandatory a) Colour TV b) LPG stoves c) Ballast d) Office Equipments

Description : On which Product is Labeling mandatory a) Colour TV b) LPG stoves c) Ballast d) Office Equipments

Last Answer : colour tv

………….. product on which labeling is voluntary. A. LPG stoves C. laptops B. Ballast D. All of above

Description : ………….. product on which labeling is voluntary. A. LPG stoves C. laptops B. Ballast D. All of above

Last Answer : all of above

Formula for adding weight (ballast) on tractor tyres working in loose wet soil for good traction a)(km/hr × kg/PTO kw)=540 b)( km/hr × kg/PTO kw)=670 c)( km/hr × kg/PTO HP)=540 d)( km/hr × kg/PTO HP)=670

Description : Formula for adding weight (ballast) on tractor tyres working in loose wet soil for good traction a)(km/hr × kg/PTO kw)=540 b)( km/hr × kg/PTO kw)=670 c)( km/hr × kg/PTO HP)=540 d)( km/hr × kg/PTO HP)=670

Last Answer : a)(km/hr × kg/PTO kw)=540

Stone generally preferred for railway ballast is a) Sandstone b) Dolomite c) Marble d) Basalt or trap granite*

Description : Stone generally preferred for railway ballast is a) Sandstone b) Dolomite c) Marble d) Basalt or trap granite*

Last Answer : d) Basalt or trap granite*

For laying a Railway track the prepared surface ready to receive the ballast is called a) Sub ballast b) Formation* c) Blanket d) Cushion

Description : For laying a Railway track the prepared surface ready to receive the ballast is called a) Sub ballast b) Formation* c) Blanket d) Cushion

Last Answer : b) Formation*

Cross slope of the formation to have good drainage of Ballast section is a) 1 in 40* b) 1 in 50 c) 1 in 30 d) 1 in 20

Description : Cross slope of the formation to have good drainage of Ballast section is a) 1 in 40* b) 1 in 50 c) 1 in 30 d) 1 in 20

Last Answer : a) 1 in 40*

In case of LWR track, full ballast section as specified in LWR Manual should be provided up to ……….. from the bridge abutment. a) 200 m b) 50 m c) 300 m d) 100 m*

Description : In case of LWR track, full ballast section as specified in LWR Manual should be provided up to ……….. from the bridge abutment. a) 200 m b) 50 m c) 300 m d) 100 m*

Last Answer : d) 100 m

Wing walls and return walls are provided to retain a) earth on approaches b) ballast c) track on approaches d) none

Description : Wing walls and return walls are provided to retain a) earth on approaches b) ballast c) track on approaches d) none

Last Answer : a) earth on approaches

Track structure for CC+8 t+ 2 t loaded trains is:- (a) 52 Kg 90 UTS;PSC 1540 sleepers/ Km.; 250 mm ballast. (b) 60 Kg 90 UTS;PSC 1660 sleepers/ Km.; 300 mm ballast.* (c) 52 Kg 72 UTS;PSC 1540 sleepers/ Km.; 300 mm ballast. (d) 90 R;PSC 1340 sleepers/ Km.; 250 mm ballast.

Description : Track structure for CC+8 t+ 2 t loaded trains is:- (a) 52 Kg 90 UTS;PSC 1540 sleepers/ Km.; 250 mm ballast. (b) 60 Kg 90 UTS;PSC 1660 sleepers/ Km.; 300 mm ballast.* (c) 52 Kg 72 UTS;PSC 1540 sleepers/ Km.; 300 mm ballast. (d) 90 R;PSC 1340 sleepers/ Km.; 250 mm ballast.

Last Answer : b) 60 Kg 90 UTS;PSC 1660 sleepers/ Km.; 300 mm ballast.*

Minimum depth of ballast cushion below the bottom of sleeper at the rail seat on BG group A route should be :- (a) 350 mm. (b) 250 mm. (c) 300 mm.* (d) 325 mm.

Description : Minimum depth of ballast cushion below the bottom of sleeper at the rail seat on BG group A route should be :- (a) 350 mm. (b) 250 mm. (c) 300 mm.* (d) 325 mm.

Last Answer : (c) 300 mm.*

How to Replace a Fluorescent Light Ballast ?

Description : How to Replace a Fluorescent Light Ballast ?

Last Answer : How to Replace a Fluorescent Light Ballast You can count on fluorescent bulbs to shine brightly for different areas in your home, but they need to be replaced every now and then. Sometimes though, the ... time by replacing the ballast. Just follow these easy tips and you'll do this in no time.

Mickey is fishing from his row boat at his favorite spot in the lake. He has a large rock in the bottom of the boat for stability and ballast. Mickey decides to call it quits. To lighten his load, he tosses the rock overboard before rowing to shore. Does the water level of the lake: w) go up x) go down y) remain the same

Description : Mickey is fishing from his row boat at his favorite spot in the lake. He has a large rock in the bottom of the boat for stability and ballast. Mickey decides to call it quits. To lighten his load, he tosses the ... to shore. Does the water level of the lake: w) go up x) go down y) remain the same

Last Answer : ANSWER: X -- GO DOWN

When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when:

Description : When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when:  a) Static strain are being measured b) Dynamic strain are being measured c) Both Static and dynamic strain are being measured d) None of the above

Last Answer : When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when: Dynamic strain are being measured

Compare electromechanical switching system with electronic switching system.

Description : Compare electromechanical switching system with electronic switching system.

Last Answer : Ans:

Compare Electronic controllers with pneumatic controllers.

Description : Compare Electronic controllers with pneumatic controllers.

Last Answer : Electronic contrllers Pneumatic controller Low power requirements High power requirements Speed of response is substantially instantaneous Speed of response is not substantially ... Difficult maintenance and test kit requirements Essay maintenance and test kit requirements

State the needs and benefits of star labelling.

Description : State the needs and benefits of star labelling. 

Last Answer : Needs of star labelling: * Star labelling is meanly required to recognize quality of product * Star labelling is also required to determine life and efficiency of the product. * Star labels ... emission and air pollution will be reduces. 5. Market efficiency and compilation will be improve. 

State the difference between energy conservation and energy audit.

Description : State the difference between energy conservation and energy audit. 

Last Answer : energy conservation Energy audit It is reducing the growth of energy consumption by avoiding unnecessary usage of energy It is an inspection, survey & analysis of energy flows ... Various measuring instruments, with proper sensing elements are required for the energy audit. 

State the losses in secondary distribution system.

Description : State the losses in secondary distribution system. 

Last Answer : The losses in secondary distribution system: a) Technical losses: 1. Due to poor voltage 2. Due to unbalance load 3. Due poor quality of transformer & its components 4. Due to poor quality ... of induction type of energy meter. 3. Lack of administration. 4. Energy theft 5. Unmetered supply

State the working principle and operation of Automatic power factor controller used in Transmission and Distribution system.

Description : State the working principle and operation of Automatic power factor controller used in Transmission and Distribution system.

Last Answer : Diagram of Automatic over factor controller Automatic Power factor control: The pf controller is used to maintain the pf at unity across the lines it is connected. Maintaining the pf at ... the load demand in the system is increased. 8. Check if power transformer compensation is provided.

State and explain the factors that govern the selection of cogeneration system for an industry.

Description : State and explain the factors that govern the selection of cogeneration system for an industry.

Last Answer : The factors that govern the selection of cogeneration system for an industry: The factors that govern the selection of cogeneration systems are very much site/situation specific. The local factors ... require is generated. If required energy demand is higher electricity purchased from grid. 

State and explain the desirable characteristics of a Tariff.

Description : State and explain the desirable characteristics of a Tariff. 

Last Answer : The desirable characteristics of a Tariff: 1. It should be easy to understand to consumer. 2. Easy to calculate. 3. Tariff should be attractive i.e. It should not be too high or ... industrial consumer, in addition to basic tariff incentives and penalty related to PF and LF should be considered.

State the need of cogeneration in present scenario.

Description : State the need of cogeneration in present scenario.

Last Answer : Need for co-generation in present scenario: 1. In conventional power plant efficiency is only 35% & remaining 65% of energy is lost. 2. The conventional system uses energy of fuel ... economical solution to energy shortages. 4. Increases financial capital. 5. Increases environmental value. 

State and explain "power factor tariff'.

Description : State and explain "power factor tariff'.

Last Answer : Power Factor Tariff:- In addition to basic tariff (Maximum Demand Tariff / KVA Maximum Demand Tariff / Load factor tariff) the tariff in which P.F. of industrial consumer is taken into consideration. ... consumer/H.T/ commercial consumers with contract demand above 80 kw/ 100Kva/107 hp consumer.

State how 'parallel operation of transformers' helps in energy conservation.

Description : State how 'parallel operation of transformers' helps in energy conservation.

Last Answer : 'Parallel operation of transformers' helps in energy conservation: The transformers operate near their maximum efficiency at around 70 % to 100 % of their rated loads. For a huge load system drawing highly ... if of higher rating may be put in service while the first one may be switched off.

State the significant features of Energy Efficient Motor.

Description : State the significant features of Energy Efficient Motor.

Last Answer : Significant features of Energy Efficient Motor: 1. Material used is of high quality. ( High flux density & High current density) 2. Due to high quality material luminous used are ... Less (negligible) maintenance. 7. Operating temperature with standing capacity is more without any problem.

State the different types of tariffs. Explain any one.

Description : State the different types of tariffs. Explain any one.

Last Answer : Different types of tariffs: i) Simple tariff ii) Flat rate tariff iii) Block rate tariff iv) Two part tariff v) Maximum demand tariff vi) Power factor tariff vii) Three part tariff viii) Time- ... the rates are low. So that the consumers are encouraged to use the electricity during non-peak hours.

State two benefits and applications of variable frequency drives.

Description : State two benefits and applications of variable frequency drives. 

Last Answer : Benefits and applications of variable frequency drives: The variable frequency drive helps to conserve electrical energy and gives the following benefits: 1) Energy saving due to optimum use for applications ... 4) Process control drives. 5) Textile industry machines. 6) Paper industry machines.