The capillary rise of mercury is maximum in glass tube of dia __________ mm. (A) 0.5 (B) 1 (C) 2 (D) 5

The capillary rise of mercury is maximum in glass tube of dia
__________ mm.
(A) 0.5
(B) 1
(C) 2
(D) 5
by

1 Answer

Answer :

(A) 0.5
by

Related questions

If two capillary tubes of dia 0.5 mm and 1 mm are dipped in a pot containing mercury, then the rise of mercury is (A) Same in both the tubes (B) Greater in 1 mm dia tube (C) Greater in 0.5 mm dia tube (D) Zero in both the tubes

Description : If two capillary tubes of dia 0.5 mm and 1 mm are dipped in a pot containing mercury, then the rise of mercury is (A) Same in both the tubes (B) Greater in 1 mm dia tube (C) Greater in 0.5 mm dia tube (D) Zero in both the tubes

Last Answer : (C) Greater in 0.5 mm dia tube

The capillary rise at 20°C in a clean glass tube of 1 mm bore containing water is approximately (A) 5 mm (B) 10 mm (C) 20 mm (D) 30 mm

Description : The capillary rise at 20°C in a clean glass tube of 1 mm bore containing water is approximately (A) 5 mm (B) 10 mm (C) 20 mm (D) 30 mm

Last Answer : Answer: Option D

Capillary rise of mercury in a small diameter tube is proportional to (where, d = diameter of the tube, σ = surface tension of mercury) (A) d (B) 1/d (C) σ (D) 1/σ

Description : Capillary rise of mercury in a small diameter tube is proportional to (where, d = diameter of the tube, σ = surface tension of mercury) (A) d (B) 1/d (C) σ (D) 1/σ

Last Answer : (C) σ

A glass tube of smaller diameter is used while performing an experiment for the capillary rise of water because (A) It is easier to see through the glass tube (B) Glass tube is cheaper than a metallic tube (C) It is not possible to conduct this experiment with any other tube (D) All of the above

Description : A glass tube of smaller diameter is used while performing an experiment for the capillary rise of water because (A) It is easier to see through the glass tube (B) Glass tube is cheaper than a metallic ... (C) It is not possible to conduct this experiment with any other tube (D) All of the above

Last Answer : Answer: Option A

. A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these

Description : . A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these

Last Answer : (A) 4.4 KPa

Correction for capillary effect in manometers (used for pressure measurement) need not be applied, if diameter of the manometer tube is __________ mm. (A) < 4 (B) > 4 (C) > 12.5 (D) < 10

Description : Correction for capillary effect in manometers (used for pressure measurement) need not be applied, if diameter of the manometer tube is __________ mm. (A) < 4 (B) > 4 (C) > 12.5 (D) < 10

Last Answer : (C) > 12.5

Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014

Description : Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014

Last Answer : (B) 0.30

Very small pressure difference (< 5 mm water column) can be most conveniently measured by a/an __________ manometer. (A) U-tube water (B) U-tube mercury (C) Inclined tube mercury (D) Inclined tube water

Description : Very small pressure difference (< 5 mm water column) can be most conveniently measured by a/an __________ manometer. (A) U-tube water (B) U-tube mercury (C) Inclined tube mercury (D) Inclined tube water

Last Answer : (D) Inclined tube water

Rise of liquid in a capillary tube is due to (A) Cohesion (B) Adhesion (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Rise of liquid in a capillary tube is due to (A) Cohesion (B) Adhesion (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B

Water rises in a capillary tube to a height h. It will rise to a height more than h. a.in a lift moving up with an acceleration b.in all the above cases c.107 dynes d.at the poles e.on the surface of moon

Description : Water rises in a capillary tube to a height h. It will rise to a height more than h. a.in a lift moving up with an acceleration b.in all the above cases c.107 dynes d.at the poles e.on the surface of moon

Last Answer : e. on the surface of moon

Let a tin capillary tube be replaced with another tube of insufficient length then we find that water (a) Will overflow (b) Will not rise (c) Depress (d) Changes its meniscus

Description : Let a tin capillary tube be replaced with another tube of insufficient length then we find that water (a) Will overflow (b) Will not rise (c) Depress (d) Changes its meniscus

Last Answer : Ans:(b)

What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Description : What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Last Answer : (D) 0.66

Thermometer bulb & capillary in case of mercury filled pressure spring expansion thermometer is normally made of __________ as mercury does not amalgamate with it. (A) Copper (B) Copper alloys (C) Stainless steel (D) Monel

Description : Thermometer bulb & capillary in case of mercury filled pressure spring expansion thermometer is normally made of __________ as mercury does not amalgamate with it. (A) Copper (B) Copper alloys (C) Stainless steel (D) Monel

Last Answer : (C) Stainless steel

If an ordinary glass tube and a glass capillary tube are 'both clipped in a beaker of water, water rises in – (1) both (2) only the glass tube (3) only the capillary tube (4) neither

Description : If an ordinary glass tube and a glass capillary tube are 'both clipped in a beaker of water, water rises in – (1) both (2) only the glass tube (3) only the capillary tube (4) neither

Last Answer : (1) both Explanation: The rise or fall of liquid due to capillarity in a beaker of water depends upon the radius of the bore of the tube (s) which is/are dipped into it. The narrower the bore of ... in the tube. So in this case, water will rise in both the glass tube and the glass capillary tube.

If an ordinary glass tube and a glass capillary tube are both dipped in a beaker of water, water rises in (1) both (2) only the glass tube (3) only the capillary tube (4) neither

Description : If an ordinary glass tube and a glass capillary tube are both dipped in a beaker of water, water rises in (1) both (2) only the glass tube (3) only the capillary tube (4) neither

Last Answer : both

The length of the countersunk head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Description : The length of the countersunk head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Last Answer : a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof *

he length of the snap head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Description : he length of the snap head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Last Answer : a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof *

The diameter of hole for 20 dia rivet shall be a) 23 mm b) 18 mm c) 21.5 mm* d) 22 mm

Description : The diameter of hole for 20 dia rivet shall be a) 23 mm b) 18 mm c) 21.5 mm* d) 22 mm

Last Answer : c) 21.5 mm*

In a residential colony, sewers of diameters 100 mm, 150 mm and 225 mm were laid with a gradient 1 in 120. Which portion of the sewage system does not choke in due course of time? A. 100 mm dia. B. 150 mm dia. C. 225 mm dia. D. All of these

Description : In a residential colony, sewers of diameters 100 mm, 150 mm and 225 mm were laid with a gradient 1 in 120. Which portion of the sewage system does not choke in due course of time? A. 100 mm dia. B. 150 mm dia. C. 225 mm dia. D. All of these

Last Answer : ANS: C

For high level flush the nominal dia of flush pipe shall be (a) 32 mm* (b) 40 mm (c) 25 mm (d) None of these

Description : For high level flush the nominal dia of flush pipe shall be (a) 32 mm* (b) 40 mm (c) 25 mm (d) None of these

Last Answer : a) 32 mm*

What is the dia of thimble ? (i) 14-16 mm (ii) 16-18 mm* (iii) 18-20 mm (iv) None of the above

Description : What is the dia of thimble ? (i) 14-16 mm (ii) 16-18 mm* (iii) 18-20 mm (iv) None of the above

Last Answer : (ii) 16-18 mm*

A liquid flows through a capillary tube. Then the velocity of the liquid is (a) Maximum at the walls of the tubs (b) Constant at all points in the cross section of the tube (c) Maximum along the axis of the tube (d) Independent of the pressure-head

Description : A liquid flows through a capillary tube. Then the velocity of the liquid is (a) Maximum at the walls of the tubs (b) Constant at all points in the cross section of the tube (c) Maximum along the axis of the tube (d) Independent of the pressure-head

Last Answer : Ans:(c)

Mercury is an ideal barometric fluid mainly due to its(A) High density (B) Low compressibility (C) Low capillary action (D) Very low vapor pressure

Description : Mercury is an ideal barometric fluid mainly due to its (A) High density (B) Low compressibility (C) Low capillary action (D) Very low vapor pressure

Last Answer : (D) Very low vapor pressure

A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Description : A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Last Answer : (A) 7

If to torricelli had drilled a little hole at the top of the glass tube holding his mercury column what would have happened to his barometer?

Description : If to torricelli had drilled a little hole at the top of the glass tube holding his mercury column what would have happened to his barometer?

Last Answer : He would not have had a barometer. He would have had a glass tube stuck into a bowl of Mercury, with nothing in it. Because once the hole was made the vacuum would be gone and the Mercury would fall back down to the bowl.It takes the vacuum in the tube to create a barometer.

The surface tension of mercury at normal temperature compared to that of water is (A) More (B) Less (C) Same (D) More or less depending on size of glass tube

Description : The surface tension of mercury at normal temperature compared to that of water is (A) More (B) Less (C) Same (D) More or less depending on size of glass tube

Last Answer : Answer: Option A

Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocity(B) Newton's law of viscosity is not applicable to the turbulent flow of fluidwith linear velocity distribution(C) Laminar flow of viscous liquids is involved in the lubrication of varioustypes of bearings(D) Rise of water in capillary tubes reduces with the increasing diameter ofcapillary tubes

Description : Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocit (B) Newton's law of viscosity is not applicable to the ... types of bearings (D) Rise of water in capillary tubes reduces with the increasing diameter of capillary tubes

Last Answer : (B) Newton's law of viscosity is not applicable to the turbulent flow of fluid with linear velocity distribution

Tray spacing in a distillation column of dia 10-12 ft. used in petroleum refinery may be around __________ inches. (A) 5 (B) 30 (C) 60 (D) 100

Description : Tray spacing in a distillation column of dia 10-12 ft. used in petroleum refinery may be around __________ inches. (A) 5 (B) 30 (C) 60 (D) 100

Last Answer : (B) 30

Capillary tube method of viscosity measurement is based on the (A) Hagen-Poiseuille’s equation (B) Stoke's law (C) Navier-stokes equation (D) None of these

Description : Capillary tube method of viscosity measurement is based on the (A) Hagen-Poiseuille’s equation (B) Stoke's law (C) Navier-stokes equation (D) None of these

Last Answer : (A) Hagen-Poiseuille’s equation

Which of the following statements about septic shock are true? A. A circulating myocardial depressant factor may account for the cardiac dysfunction sometimes seen with shock due to sepsis or SIRS. B. A cardiac index (CI) of 6 liters per minute per square meter of body surface, a pulmonary capillary wedge pressure of 15 mm. Hg, and a systemic vascular resistance index (SVRI) of 800 dynes-sec/(cm 5-m 2) is a hemodynamic profile consistent with septic shock. C. An increase in SvO 2 in septic patients may be explained by the finding of anatomic arteriovenous shunts. D. Results of human trials employing antimediator therapy, such as antiendotoxin antibodies, IL-1 receptor antagonist, and tumor necrosis factor (TNF) antibodies, have confirmed animal studies that demonstrate a significant im

Description : Which of the following statements about septic shock are true? A. A circulating myocardial depressant factor may account for the cardiac dysfunction sometimes seen with shock due to sepsis or ... animal studies that demonstrate a significant improvement in survival with the use of such agents.

Last Answer : Answer: AB DISCUSSION: Shock due to sepsis or SIRS frequently manifests as a hyperdynamic cardiovascular response, consisting of an elevated CI and a decreased SVR or SVRI. Occasionally, ... been encouraging thus far in human clinical trials, despite the promising results from many animal studies

If the diameter of a capillary is doubled, then the rise of water in it will be – (1) two times (2) half (3) four times (4) no change

Description : If the diameter of a capillary is doubled, then the rise of water in it will be – (1) two times (2) half (3) four times (4) no change

Last Answer : (2) half Explanation: Radius of a capillary tube is inversely proportional to the height of the liquid column. So, if radius of the tube is doubled, rise of level of water will becomes half ... to flow in narrow spaces without the assistance of, and in opposition to external forces like gravity.

The capillary rise of water (A) Depends upon the force responsible (B) Increases as the size of the soil particles increases (C) Decreases as the size of the soil particles decreases (D) Is less in wet soil than in dry soil

Description : The capillary rise of water (A) Depends upon the force responsible (B) Increases as the size of the soil particles increases (C) Decreases as the size of the soil particles decreases (D) Is less in wet soil than in dry soil

Last Answer : (A) Depends upon the force responsible

Minimum thickness of a layer of fine sand required to cut off capillary rise of water completely, should be (A) 40 cm(B) 52 cm (C) 64 cm (D) 76 cm

Description : Minimum thickness of a layer of fine sand required to cut off capillary rise of water completely, should be (A) 40 cm (B) 52 cm (C) 64 cm (D) 76 cm

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Sand consists of coarse particles of silica formed due to the disintegration of rocks (B) The grains of sand are not affected by frost (C) Sand beds are permeable and do not allow water to rise up between pores due to capillary action (D) All the above

Description : Pick up the correct statement from the following: (A) Sand consists of coarse particles of silica formed due to the disintegration of rocks (B) The grains of sand are not affected by frost (C) Sand ... and do not allow water to rise up between pores due to capillary action (D) All the above

Last Answer : Answer: Option D

If the diameter of a capillary is doubled, then the rise of water in it will be (1) two times (2) half (3) four times (4) no change

Description : If the diameter of a capillary is doubled, then the rise of water in it will be (1) two times (2) half (3) four times (4) no change

Last Answer : half

__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C. (A) Borosilicate (B) High silica (C) Supermax (D) Lead

Description : __________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C. (A) Borosilicate (B) High silica (C) Supermax (D) Lead

Last Answer : (C) Supermax

A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Description : A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Last Answer : (B) 0.025

Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Description : Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Last Answer : Ans: d

A capillary tube is kept vertical in a beaker containing liquid. The height to which the liquid rises by capillary action is increased if (a) The radius of the capillary is large (b) The radius of the capillary is small (c) The density of the liquid is large (d) The surface tension of the liquid is small

Description : A capillary tube is kept vertical in a beaker containing liquid. The height to which the liquid rises by capillary action is increased if (a) The radius of the capillary is large (b) The radius of the ... small (c) The density of the liquid is large (d) The surface tension of the liquid is small

Last Answer : Ans:(b)

The coefficient of viscosity may be determined by (A) Capillary tube method (B) Orifice type viscometer (C) Rotating cylinder method (D) All of these

Description : The coefficient of viscosity may be determined by (A) Capillary tube method (B) Orifice type viscometer (C) Rotating cylinder method (D) All of these

Last Answer : Answer: Option D

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

The co-efficient of discharge of an orificemeter is a function of (A) Reynolds number at the orifice (B) Ratio of orifice dia to pipe dia (C) Both (A) and (B) (D) None of the above parameters, and has a constant value of 0.61

Description : The co-efficient of discharge of an orificemeter is a function of (A) Reynolds number at the orifice (B) Ratio of orifice dia to pipe dia (C) Both (A) and (B) (D) None of the above parameters, and has a constant value of 0.61

Last Answer : (C) Both (A) and (B)

Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Last Answer : (B) 25

The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm. (A) 0.5 (B) 3 (C) 10 (D) 25

Description : The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm. (A) 0.5 (B) 3 (C) 10 (D) 25

Last Answer : (B) 3

You are given a mercury manometer range 0 -760 mm ? A vacuum gauge reads 60 mm vacuum. The test manometer reads 50 vacuum ? Which of the two in correct.

Description : You are given a mercury manometer range 0 -760 mm ? A vacuum gauge reads 60 mm vacuum. The test manometer reads 50 vacuum ? Which of the two in correct.

Last Answer : The transmitter is correct because 760 - 50 = 710 mm abs.

Pressure difference between two points in vessels, pipelines or in two different pipelines can be measured by a differential manometer. The pressure difference measured as the mm of water column in case of mercury-water, differential manometer is equal to (where, H = difference in height of mercury column in mm). (A) H (B) 12.6 H (C) 13.6 H (D) 14.6 H

Description : Pressure difference between two points in vessels, pipelines or in two different pipelines can be measured by a differential manometer. The pressure difference measured as the mm of water column in case of mercury-water, differential manometer is ... mm). (A) H (B) 12.6 H (C) 13.6 H (D) 14.6 H

Last Answer : (B) 12.6 H

A suspension of glass beads in ethylene glycol has a hindered settling velocity of 1.7 mm/s, while the terminal settling velocity of a single glass bead in ethylene glycol is 17 mm/s. If the Richardson-Zaki hindered settling index is 4.5, the volume fraction of solids in the suspension is (A) 0.1 (B) 0.4 (C) 0.6 (D) None of these

Description : A suspension of glass beads in ethylene glycol has a hindered settling velocity of 1.7 mm/s, while the terminal settling velocity of a single glass bead in ethylene glycol is 17 mm/s. If the Richardson-Zaki hindered settling index ... in the suspension is (A) 0.1 (B) 0.4 (C) 0.6 (D) None of these

Last Answer : (C) 0.6

Maximum permissible limit of mercury in human blood is __________ micrograms/100 c.c. (A) 1 (B) 7 (C) 19 (D) 82

Description : Maximum permissible limit of mercury in human blood is __________ micrograms/100 c.c. (A) 1 (B) 7 (C) 19 (D) 82

Last Answer : (B) 7

Reynolds number for flow of water at room temperature through 2 cm dia pipe at an average velocity of 5 cm/sec is around (A) 2000 (B) 10(C) 100 (D) 1000 Answer:

Description : Reynolds number for flow of water at room temperature through 2 cm dia pipe at an average velocity of 5 cm/sec is around (A) 2000 (B) 10 (C) 100 (D) 1000 Answer:

Last Answer : (D) 1000