Description : (4) water and petrol are immiscible with each other and petrol which forms the upper layer continues to burn Explanation: Water is not effective in extinguishing a fire caused by petrol because water and ... . Water cannot generally be used to extinguish a gasoline fire, unless used in a fine mist.
Last Answer : "All the four quantum numbers of two electrons in an atom are not the same." It is the law of (1) Hund’s (2) Exclusion Principle of Pauli (3) Uncertainty Principle of Giesenberg (4) Avogadro’s law
Description : What is the unit of relative density? (1) kg/m (2) kg/m2 (3) kg/m3 (4) It has no unit
Last Answer : It has no unit
Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ
Last Answer : (A) 3.6 AVS.ρ
Description : The specific volume of air is expressed as the volume of: a. 1 kg of air at 101.325 kPa in cm3 b. 0.833 kg of air at standard pressure and temperature in m3 c. 1 kg of air at 101.325 ... d. 1 g of air occupied at any temperature and pressure e. 1 kg of air, regardless of temperature and pressure
Last Answer : Answer: C
Description : A 30-m vertical column of fluid (density 1878 kg/m3 ) is located where g= 9.65 mps2 . Find the pressure at the base of the column. (Formula: pg= gρhg/k ) a. 543680 N/m2 b. 543.68 kPa (gauge) c. Both a & b d. None of the above
Last Answer : Both a & b
Description : The bulk density of aggregates , is (a) kN/m3 (b) Kg/1tr (c) g/cm3 (d) All the above.
Last Answer : (b) Kg/1tr
Description : The actual mass of water vapour present in a given volume of moist air is — a. Relative humidity b. Absolute humidity c. Specific humidity d. All of these
Last Answer : b. Absolute humidity
Description : The term "relative humidity" applies to a) the percentage of moisture in the air as compared to the amount of moisture the air can hold at a specific temperature b) the weight of the moisture in the air c) ... of the air d) the amount of moisture in the air e) the amount of humidity in the air
Last Answer : ANSWER : A
Description : The humidity of air measured in percentage is called – (1) absolute humidity (2) specific humidity (3) relative humidity (4) all of these
Last Answer : (3) relative humidity Explanation: The relative humidity is the percent of saturation humidity, generally calculated in relation to saturated vapour density.
Description : Relative humidity is expressed as – (1) Grams (2) Kilograms (3) Percentage (4) Ratio
Last Answer : (3) Percentage Explanation: Relative humidity is the amount of moisture in the air compared to what the air can "hold" at that temperature. It signifies the mass of water vapour present in the air ... of the mass that would be present in an equal volume of saturated air at the same temperature.
Description : The percentage humidity is less than the relative humidity only at __________ percent humidity. (A) Zero (B) Hundred (C) Both zero and hundred (D) None of these
Last Answer : (C) Both zero and hundred
Description : Humidity chart is useful for the solution of problems concerning condensation, vaporisation and air conditioning. At a given dry bulb temperature, value of humidity obtained from the humidity chart directly, is in ... (A) Molal (B) Relative (C) Percentage (D) None of these
Last Answer : (A) Mola
Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity
Last Answer : Answer: Option A
Description : Relative humidity is expressed as (1) Grams (2) Kilograms (3) Percentage (4) Ratio
Last Answer : Percentage
Description : The units of moment of inertia of an area are a.kg - m b.m4 c.kg - m4 d.kg - m3 e.(kg - m)2
Last Answer : b. m4
Description : The volume of standard air is _____ m3/kg of dry air. a. 0.533 b. 0.633 c. 0.733 d. 0.833 e. 0.933
Last Answer : Answer: D
Description : SI unit for the surface tension is ____. (1) kg/m2 (2) kg/m3 (3) N/m (4) kg/m
Last Answer : (3) N/m Explanation: Surface tension is measured in force per unit length. Its SI unit is Newton per meter.
Description : Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ
Last Answer : (A) 3.6 W.D.V.ρ
Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ
Last Answer : (A) 3.6 V.W.Dr.ρ
Description : At equilibrium the concentration of water in vapour phase (C* ) in kg/m3 of air space and the amount of water (m) adsorbed per kg of dry silica gel are related by, C* = 0.0667m. To maintain dry conditions in a room ... which the temperature is maintained constant) is (A) 0.0 (B) 0.2 (C) 0.4 (D) 1.0
Last Answer : (C) 0.4
Description : Humid volume is the total volume in m3 of 1 kg of (A) Vapour laden gas at 1 atm. and room temperature (B) Gas plus its accompanying vapour at 1 atm. and room temperature (C) Gas plus its accompanying vapour at 1 atm. and gas temperature (D) Vapour laden gas at 1 atm. and gas temperature
Last Answer : (C) Gas plus its accompanying vapour at 1 atm. and gas temperature
Description : Density of Water is-----? A. 897 kg/m3 B. 997 kg/m3 (Answer) C. 1000 kg/m3 D. 1025 kg/m3
Last Answer : B. 997 kg/m3 (Answer)
Description : The density of Air is-------? A. 0.225 kg/m3 B. 1.025 kg/m3 C. 1.225 kg/m3 (Answer) D. 1.425 kg/m3
Last Answer : C. 1.225 kg/m3 (Answer)
Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50
Last Answer : (A) 32
Description : For spawing of 1 Kg of carp, how much water is required in hatchery (a) 1 m3(b) 10 m3 (c) 50 m3 (d) 80 m3
Last Answer : (a) 1 m3
Description : Calorific value of pitch creosote mixture (PCM) i.e., C.T.F.-200 is about (A) 8800 kcal/m3 (B) 8800 kcal/kg (C) Same as that of coal middling (D) 25000 kcal/kg
Last Answer : (B) 8800 kcal/kg
Description : Bulk density of pulverised coal may be about __________ kg/m3 . (A) 100 (B) 500 (C) 1000 (D) 1500
Last Answer : (B) 500
Description : Unit of mass velocity is (A) kg/hr (B) kg/m2 . hr (C) kg/m2 (D) kg/m3 . hr
Last Answer : (B) kg/m2 . hr
Description : A bed consists of particles of density 2000 kg/m3 . If the height of the bed is 1.5 metres and its porosity 0.6, the pressure drop required to fluidise the bed by air is (A) 25.61 kPa (B) 11.77 kPa (C) 14.86 kPa (D) 21.13 kPa
Last Answer : (B) 11.77 kPa
Description : A gas (density = 1.5 kg/m3 , viscosity = 2 10 -5 kg/m.s) flowing through a packed bed (particle size = 0.5 cm, porosity = 0.5) at a superficial velocity of 2 m/s causes a pressure drop of 8400 Pa/m. The ... flowing at 3 m/s will be (A) 8400 Pa/m (B) 12600 Pa/m (C) 18900 Pa/m (D) 16800 Pa/m
Last Answer : (B) 12600 Pa/m
Description : . A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these
Last Answer : (A) 4.4 KPa
Description : Bed pressure drop in an air fluidised bed of catalyst particles (ρp = 200 kg/m3, Dp = 0.05 cm) of 60 cm bed depth and bed porosity of 0.5 expressed in cm of water (manometer) is (A) 90 (B) 60 (C) 45 (D) 30
Last Answer : (B) 60
Description : For an incompressible fluid, the bulk modulus of elasticity is (A) 5 kg/m3 (B) ∞ N/m2 (C) 1 N (D) 0 N/m
Last Answer : (B) ∞ N/m2
Description : . An irreversible aqueous phase reaction, A + B → P, is carried out in an adiabatic mixed flow reactor. A feed containing 4kmole/m3 of each A and B enters the reactor at 8m3 /hr. If the temperature of ... be assumed to be independent of temperature and composition. (A) 190 (B) 290 (C) 390 (D) 490
Last Answer : (B) 290
Description : The weight of reinforced concrete, is generally taken as (A) 2200 kg/m3 (B) 2300 kg/m3 (C) 2400 kg/m3 (D) 2500 kg/m
Last Answer : Answer: Option C
Description : The live load to be considered for an accessible roof, is (A) Nil (B) 75 kg/m3 (C) 150 kg/m2 (D) 200 kg/cm
Description : 19. The density of a liquid in kg/m3 is numerically equal to its specific gravity. A) True B) False
Last Answer : A
Description : The density of water is 1000 kg/m3 at (A) 0° C (B) 0° K (C) 4° C (D) 20° C
Description : An odd shaped body weighing 7.5 kg and occupying 0.01 m3 volume will be completely submerged in a fluid having specific gravity of (A) 1 (B) 1.2 (C) 0.8 (D) 0.75
Last Answer : Answer: Option D
Description : The mass of 2.5 m3 of a certain liquid is 2 tonnes. Its mass density is (A) 200 kg/m3 (B) 400 kg/m3 (C) 600 kg/m3 (D) 800 kg/m
Description : A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)
Last Answer : Answer: Option B
Description : For melting one tonne of cast iron (A) 700 m3 air is required (B) 20 kg limestone is required (C) One quintal coke is required (D) All the above
Description : The weight of 1 m3 of brick earth, is about (A) 1200 kg (B) 1500 kg (C) 1800 kg (D) 2000 kg
Description : If is the angle of repose of soil of weight w kg/m3 , the horizontal pressure p at a depth of h metres per metre length of wall, is (A) wh × [(1 - sin )/(1 + )] (B) (wh/2) × [(1 - sin )/(1 + )] (C) wh - sin )/(1 + )] (D) wh )/(1 - )
Description : The benchmarking parameter for air conditioning equipment is a) kW/Ton of Refrigeration b) kW/ kg of refrigerant handled c) kcal/m3 of chilled water d) Differential temperature across chiller
Last Answer : kW/Ton of Refrigeration
Description : The benchmarking parameter for air conditioning equipment is a) kW/Ton of Refrigeration b) kW/ kg of refrigerant handled c) kcal/m3 of chilled water d) Differential temperature across chiLLER
Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000
Last Answer : 21600
Description : Utilizing the answer to the previous problem, estimate the overall or average increase in temperature ( ΔT) of the concrete roof from the energy absorbed from the sun during a12hour day. Assume that all of the radiation absorbed goes into ... °C b. 8.9°C c. 9.9°C d. 10.9°C formula: ΔQ = m c ΔT
Last Answer : 7.9 °C
Description : Molecular volume of any perfect gas at 600 x 103 N/m2 and 27°C will be (a) 4.17m3/kgmol (b) 400 m3/kg mol (c) 0.15 m3/kg mol (d) 41.7 m3/kg mol (e) 417m3/kgmol.
Last Answer : Answer : a