Combustion of furnace oil in a furnace (soaking pit) with preheated combustion air at 400°C results in saving of about __________ percentfurnace oil as compared to its combustion with atmospheric air, if the fluegas outlet temperature from the soaking pit is 1200°C.(A) 5(B) 60(C) 20(D) 40

Combustion of furnace oil in a furnace (soaking pit) with preheated
combustion air at 400°C results in saving of about __________ percentfurnace oil as compared to its combustion with atmospheric air, if the flue
gas outlet temperature from the soaking pit is 1200°C.
(A) 5
(B) 60
(C) 20
(D) 40
by

1 Answer

Answer :

(C) 20
by

Related questions

Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Description : Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Last Answer : (C) 20

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating

Last Answer : (A) Cold rolled steel coil annealing

__________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Description : __________ is an indirectly heated furnace. (A) Open hearth furnace (B) Muffle furnace (C) Soaking pit (D) Reheating furnace

Last Answer : (B) Muffle furnace

Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Description : Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Last Answer : (A) Stoichiometric combustion air

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Description : An example of indirectly heated furnace is the (A) Soaking pit (B) Muffle furnace (C) Reheating furnace (D) None of these

Last Answer : (B) Muffle furnace

Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola

Last Answer : (B) Reheating furnace

Reducing atmosphere is maintained in a (A) Calcination kiln (B) Blast furnace (C) Soaking pit (D) L.D. converter

Description : Reducing atmosphere is maintained in a (A) Calcination kiln (B) Blast furnace (C) Soaking pit (D) L.D. converter

Last Answer : (B) Blast furnace

An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these

Description : An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these

Last Answer : (A) Soaking pit

Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Description : Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace

Last Answer : (C) Soaking pit

An example of shaft furnace is the (A) L.D. converter (B) Glass melting tank (C) Blast furnace (D) Soaking pit

Description : An example of shaft furnace is the (A) L.D. converter (B) Glass melting tank (C) Blast furnace (D) Soaking pit

Last Answer : (C) Blast furnace

Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace(C) Steam boiler(D) Coke oven

Description : Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace (C) Steam boiler (D) Coke oven

Last Answer : (D) Coke oven

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

Which of the following accentuates clinkering troubles on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportion of iron & sulphur (B) Low forced draft & fuel bed temperature (C) Thick firebed and preheated primary air (D) All (A), (B) and (C)

Description : Which of the following accentuates clinkering troubles on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportion of iron & sulphur (B) Low forced draft & fuel bed temperature (C) Thick firebed and preheated primary air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following accentuates clinkering trouble on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportions of iron & sulphur (B) Low forced draught and fuel bed temperature (C) Thick fire bed and preheated primary air (D) All (A), (B) and (C)

Description : Which of the following accentuates clinkering trouble on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportions of iron & sulphur (B) Low forced draught and fuel bed temperature (C) Thick fire bed and preheated primary air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Correct viscosity of furnace oil at the burner tip for proper atomisation is about 25 centistokes. To reduce the viscosity of high viscosity furnace oil (250 centistokes) to the correct atomisation viscosity (i.e. 25 cst), it should be preheated to about ___________°C. (A) 70 (B) 85 (C) 105 (D) 145

Description : Correct viscosity of furnace oil at the burner tip for proper atomisation is about 25 centistokes. To reduce the viscosity of high viscosity furnace oil (250 centistokes) to the correct atomisation viscosity (i.e. 25 cst), it should be preheated to about ___________°C. (A) 70 (B) 85 (C) 105 (D) 145

Last Answer : (C) 105

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Description : Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Last Answer : (D) 80

In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by (A) Conduction (B) Convection (C) Radiation (D) Cannot be predicted

Description : In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by (A) Conduction (B) Convection (C) Radiation (D) Cannot be predicted

Last Answer : (C) Radiation

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

During combustion of coal on grate, clinker formation is increased by the (A) Use of thick fire bed (B) Low fusion point of ash (< 1100° C) (C) Use of preheated primary air (D) All (A), (B) & (C)

Description : During combustion of coal on grate, clinker formation is increased by the (A) Use of thick fire bed (B) Low fusion point of ash (< 1100° C) (C) Use of preheated primary air (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of(A) Furnace oil with air(B) Furnace oil with oxygen(C) Blast furnace gas with air(D) Blast furnace gas with oxygen

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Description : Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Last Answer : (C) 150

In which of the following furnaces, the gases are sucked through the stock bed from below? (A) Soaking pit (B) Sintering machine (C) Beehive oven (D) None of these

Description : In which of the following furnaces, the gases are sucked through the stock bed from below? (A) Soaking pit (B) Sintering machine (C) Beehive oven (D) None of these

Last Answer : (B) Sintering machine

In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The function of an economiser in a boiler is to preheat the (A) Feedwater (B) Combustion air (C) Pulverised coal (D) Furnace oil

Description : The function of an economiser in a boiler is to preheat the (A) Feedwater (B) Combustion air (C) Pulverised coal (D) Furnace oil

Last Answer : (A) Feedwater

Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Description : Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Last Answer : (D) Lump coal (fixed on chain grate)

Live storage of coal in a power plant means (A) Coal ready for combustion (B) Preheated coal (C) storage of coal sufficient to meet 24 hour demand of the plant (D) Coal in transit.

Description : Live storage of coal in a power plant means (A) Coal ready for combustion (B) Preheated coal (C) storage of coal sufficient to meet 24 hour demand of the plant (D) Coal in transit.

Last Answer : storage of coal sufficient to meet 24 hour demand of the plant

Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Description : Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Last Answer : (C) 20

Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Description : Which of the following furnaces will have maximum thermal efficiency? (A) Soaking pits (B) Walking beam reheating furnace (C) Boiler furnace (D) Rotary kilns

Last Answer : (C) Boiler furnace

Regenerators are used for waste heat recovery in (A) By-product coke ovens (B) Beehive coke oven (C) Blast furnace stoves (D) Soaking pits

Description : Regenerators are used for waste heat recovery in (A) By-product coke ovens (B) Beehive coke oven (C) Blast furnace stoves (D) Soaking pits

Last Answer : (A) By-product coke ovens

Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air(C) Hydrocarbon fuel(D) Pulverised coal as fuel

Description : Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air (C) Hydrocarbon fuel (D) Pulverised coal as fuel

Last Answer : (A) Low amount of excess combustion air

Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30(C) 7 (D) 70

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

The stone ware sewers A. Are used for carrying sewage and drainage from houses B. Are manufactured from clays and shale C. After casting are dried and burnt at temperature 150°C, 700°C and 1200°C D. All the above

Description : The stone ware sewers A. Are used for carrying sewage and drainage from houses B. Are manufactured from clays and shale C. After casting are dried and burnt at temperature 150°C, 700°C and 1200°C D. All the above

Last Answer : ANS: D

The temperature produced on the power stroke of an engine can be as high as a) 1200°C b) 1400°C c) 1600°C d) 1800°C

Description : The temperature produced on the power stroke of an engine can be as high as a) 1200°C b) 1400°C c) 1600°C d) 1800°C

Last Answer : c) 1600°C

To obtain cement dry powder, lime stones and shales or their slurry, is burnt in a rotary kiln at a temperature between (A) 1100° and 1200°C (B) 1200° and 1300°C (C) 1300° and 1400°C (D) 1400° and 1500°C

Description : To obtain cement dry powder, lime stones and shales or their slurry, is burnt in a rotary kiln at a temperature between (A) 1100° and 1200°C (B) 1200° and 1300°C (C) 1300° and 1400°C (D) 1400° and 1500°C

Last Answer : D

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

Temperature and pressure in urea autoclave is (A) 120°C and 300 atm (B) 190°C and 200 atm (C) 400°C and 550 atm (D) 200°C and 10 atm

Description : Temperature and pressure in urea autoclave is (A) 120°C and 300 atm (B) 190°C and 200 atm (C) 400°C and 550 atm (D) 200°C and 10 atm

Last Answer : (B) 190°C and 200 atm

Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile matter coals are more suitable for making pulverised fuel (C) Regulation of furnace temperature and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Description : Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile ... and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Last Answer : (D) None of these