Use of pulverised coal in boilers provides (A) Higher calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace wall

Use of pulverised coal in boilers provides
(A) Higher calorific value
(B) Better combustion
(C) Smokeless burning
(D) Less erosion on furnace wall
by

1 Answer

Answer :

(B) Better combustion
by

Related questions

Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Description : Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Last Answer : (B) Better combustion

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Coal is pulverised before burning in large capacity boiler furnaces mainly to (A) Ensure its complete combustion (B) Facilitate easy ash removal (C) Enhance its calorific value (D) Provide trouble free operation

Description : Coal is pulverised before burning in large capacity boiler furnaces mainly to (A) Ensure its complete combustion (B) Facilitate easy ash removal (C) Enhance its calorific value (D) Provide trouble free operation

Last Answer : (A) Ensure its complete combustion

The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal(C) Accelerates the burning rate and economises on fuel combustion(D) All (A), (B) and (C)

Description : The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel combustion (D) All (A), (B) and (C)

Last Answer : (C) Accelerates the burning rate and economises on fuel combustion

Emission of dense white smoke out of the chimney of a thermal power plant is an indication of the use of (A) Less air for combustion (B) Correct amount of air for combustion (C) Too much air for combustion (D) Pulverised coal in boilers

Description : Emission of dense white smoke out of the chimney of a thermal power plant is an indication of the use of (A) Less air for combustion (B) Correct amount of air for combustion (C) Too much air for combustion (D) Pulverised coal in boilers

Last Answer : (C) Too much air for combustion

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Limestone powder is injected during pulverised coal burning in boilers to __________ the flue gases. (A) Reduce SO2 content in (B) Catalytically convert SO2 to SO3 in (C) Increase the dew point of (D) None of these

Description : Limestone powder is injected during pulverised coal burning in boilers to __________ the flue gases. (A) Reduce SO2 content in (B) Catalytically convert SO2 to SO3 in (C) Increase the dew point of (D) None of these

Last Answer : (A) Reduce SO2 content in

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air(C) Hydrocarbon fuel(D) Pulverised coal as fuel

Description : Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air (C) Hydrocarbon fuel (D) Pulverised coal as fuel

Last Answer : (A) Low amount of excess combustion air

The function of an economiser in a boiler is to preheat the (A) Feedwater (B) Combustion air (C) Pulverised coal (D) Furnace oil

Description : The function of an economiser in a boiler is to preheat the (A) Feedwater (B) Combustion air (C) Pulverised coal (D) Furnace oil

Last Answer : (A) Feedwater

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Description : Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Last Answer : (D) Lump coal (fixed on chain grate)

The advantages of firing pulverised coal in the furnace lies in the fact that, it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel consumption (D) All (A), (B) and (C)

Description : The advantages of firing pulverised coal in the furnace lies in the fact that, it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel consumption (D) All (A), (B) and (C)

Last Answer : (C) Accelerates the burning rate and economises on fuel consumption

Which of the following is not applicable to fluidised bed combustion of coal? (A) It cannot burn low grade coal (B) It achieves higher fuel combustion efficiency (C) Less heat transfer surface area is required in boilers (D) None of these

Description : Which of the following is not applicable to fluidised bed combustion of coal? (A) It cannot burn low grade coal (B) It achieves higher fuel combustion efficiency (C) Less heat transfer surface area is required in boilers (D) None of these

Last Answer : (A) It cannot burn low grade coal

Which of the following is the most important deterrents to an extended use of pulverised coal in boiler firing? (A) Ash disposal problem (B) Excessive fly ash discharge from the stack (C) Higher power consumption in its transportation (D) Erosion of induced draft fan blades

Description : Which of the following is the most important deterrents to an extended use of pulverised coal in boiler firing? (A) Ash disposal problem (B) Excessive fly ash discharge from the stack (C) Higher power consumption in its transportation (D) Erosion of induced draft fan blades

Last Answer : (A) Ash disposal problem

Junker's calorimeter is used to determine the calorific value of (A) Pulverised coal (B) Gaseous fuels (C) Fuel oil (D) None of these

Description : Junker's calorimeter is used to determine the calorific value of (A) Pulverised coal (B) Gaseous fuels (C) Fuel oil (D) None of these

Last Answer : (B) Gaseous fuels

A particular coal is said to be free burning when it (A) Burns completely (B) Gives smokeless burning (C) Shows little or no fusing action (D) None of these

Description : A particular coal is said to be free burning when it (A) Burns completely (B) Gives smokeless burning (C) Shows little or no fusing action (D) None of these

Last Answer : (C) Shows little or no fusing action

Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile matter coals are more suitable for making pulverised fuel (C) Regulation of furnace temperature and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Description : Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile ... and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Last Answer : (D) None of these

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Description : Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Last Answer : (A) Requires larger combustion chamber than rich gaseous fuel

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Description : Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Last Answer : (D) Both (A) and (B)

Which of the following is the most important deterrents to an extended use of pulverised coal in boiler firing? (A) Ash disposal problem (B) Excessive fly-ash discharge from the stack (C) High power consumption in its transportation (D) Erosion of induced draft fan blades

Description : Which of the following is the most important deterrents to an extended use of pulverised coal in boiler firing? (A) Ash disposal problem (B) Excessive fly-ash discharge from the stack (C) High power consumption in its transportation (D) Erosion of induced draft fan blades

Last Answer : (A) Ash disposal problem

In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Description : In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Last Answer : (C) Combustion of coal by supplying it around the burner

The function of secondary combustion air is to (A) Pneumatically convey the pulverised coal (B) Completely burn the volatile matter (C) Burn the lumpy coal (D) None of these

Description : The function of secondary combustion air is to (A) Pneumatically convey the pulverised coal (B) Completely burn the volatile matter (C) Burn the lumpy coal (D) None of these

Last Answer : (B) Completely burn the volatile matter

The main function of primary air in pulverised coal fired burner is to (A) Burn CO to CO2 (B) Dry and transport the coal (C) Have proper combustion by supplying it around the burner (D) Preheat the tertiary air used for complete combustion of CO to CO2

Description : The main function of primary air in pulverised coal fired burner is to (A) Burn CO to CO2 (B) Dry and transport the coal (C) Have proper combustion by supplying it around the burner (D) Preheat the tertiary air used for complete combustion of CO to CO2

Last Answer : (B) Dry and transport the coal

In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Description : In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Last Answer : (C) Combustion of coal by supplying it around the burner

The excess air required for the combustion of pulverised coal is of the order of about __________ percent. (A) 5 (B) 15 (C) 30 (D) 45

Description : The excess air required for the combustion of pulverised coal is of the order of about __________ percent. (A) 5 (B) 15 (C) 30 (D) 45

Last Answer : (B) 15

Fuel used in B.F. stove is (A) Pulverised coal (B) Furnace oil (C) Blast furnace gas/mixed gas (D) Coke oven gas

Description : Fuel used in B.F. stove is (A) Pulverised coal (B) Furnace oil (C) Blast furnace gas/mixed gas (D) Coke oven gas

Last Answer : (C) Blast furnace gas/mixed gas

Which of the following fuels is generally not used in thermal power plant boiler firing? (A) Furnace oil, light diesel oil and tar/PCM (B) Pulverised coking coal (C) Coal middling from washeries (D) B.F. gas, coke oven gas and L.D. converter gas

Description : Which of the following fuels is generally not used in thermal power plant boiler firing? (A) Furnace oil, light diesel oil and tar/PCM (B) Pulverised coking coal (C) Coal middling from washeries (D) B.F. gas, coke oven gas and L.D. converter gas

Last Answer : (B) Pulverised coking coal

Function of secondary air in pulverised coal firing is to (A) Transport the coal to the burner (B) Dry the coal (C) Ensure efficient burning of coal around the burner (D) Reduce primary air requirement

Description : Function of secondary air in pulverised coal firing is to (A) Transport the coal to the burner (B) Dry the coal (C) Ensure efficient burning of coal around the burner (D) Reduce primary air requirement

Last Answer : (C) Ensure efficient burning of coal around the burner

A travelling grate stoker is meant for the efficient burning of __________ coal. (A) Caking (B) Pulverised (C) Non-caking (D) High ash

Description : A travelling grate stoker is meant for the efficient burning of __________ coal. (A) Caking (B) Pulverised (C) Non-caking (D) High ash

Last Answer : (C) Non-caking

Which of the following fuels is the best for burning on chain grate stoker? (A) Non-caking coal (B) Caking coal (C) Coking coal (D) Pulverised coal

Description : Which of the following fuels is the best for burning on chain grate stoker? (A) Non-caking coal (B) Caking coal (C) Coking coal (D) Pulverised coal

Last Answer : (A) Non-caking coal

Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Description : Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Last Answer : (C) Friability & oxygen content

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

With increase in moisture content of coal, its (A) Calorific value increases sometimes (B) Bulk density always decreases (C) Clinkering tendency during combustion increases (D) None of these

Description : With increase in moisture content of coal, its (A) Calorific value increases sometimes (B) Bulk density always decreases (C) Clinkering tendency during combustion increases (D) None of these

Last Answer : (D) None of these

Which of the following fuels has the highest calorific value per unit mass (kcal/kg)? (A) Coal (B) Kerosene (C) Natural gas (D) Furnace oil

Description : Which of the following fuels has the highest calorific value per unit mass (kcal/kg)? (A) Coal (B) Kerosene (C) Natural gas (D) Furnace oil

Last Answer : (D) Furnace oil

Out of the following fuels, the difference between the net and gross calorific value is maximum in case of (A) Pitch (B) Fuel oil (C) Blast furnace gas (D) Bituminous coal

Description : Out of the following fuels, the difference between the net and gross calorific value is maximum in case of (A) Pitch (B) Fuel oil (C) Blast furnace gas (D) Bituminous coal

Last Answer : (B) Fuel oil

are portable devices capable of estimating the combusting efficiency of furnaces, boilers, or other fossil fuel burning machines. a) Sound analyzer. c) Combustion analyzer. b) Light analyzer. d)Temperature analyzer

Description : are portable devices capable of estimating the combusting efficiency of furnaces, boilers, or other fossil fuel burning machines. a) Sound analyzer. c) Combustion analyzer. b) Light analyzer. d)Temperature analyzer

Last Answer : Combustion analyzer. 

are portable devices capable of estimating the combusting efficiency of furnaces, boilers, or other fossil fuel burning machines. a) Sound analyzer. b) Light analyzer. c) Combustion analyzer. d) Temperature analyzer.

Description : are portable devices capable of estimating the combusting efficiency of furnaces, boilers, or other fossil fuel burning machines. a) Sound analyzer. b) Light analyzer. c) Combustion analyzer. d) Temperature analyzer.

Last Answer : Combustion analyzer.

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

Pick out the correct statement. (A) Oxygen content decreases from lignite to bituminous coal as the coalification increases (B) The less the oxygen content, better is the coal, as it reduces the calorific value (C) With increase in oxygen content, moisture holding capacity of coal increases and the caking power decreases (D) All (A), (B) and (C)

Description : Pick out the correct statement. (A) Oxygen content decreases from lignite to bituminous coal as the coalification increases (B) The less the oxygen content, better is the coal, as it reduces the calorific value (C ... capacity of coal increases and the caking power decreases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Net calorific value is the gross calorific value less the __________ heat of water in the product of combustion when cooled to 15°C(A) Sensible (B) Latent (C) Sensible and latent (D) None of these.

Description : Net calorific value is the gross calorific value less the __________ heat of water in the product of combustion when cooled to 15°C. (A) Sensible (B) Latent (C) Sensible and latent (D) None of these

Last Answer : (C) Sensible and latent

Ratio of primary air to secondary air increases with increase in the rank of coal, because the (A) High rank coals have higher amount of volatile matter (B) Ratio of fixed carbon to volatile matter increases (C) Oxygen content progressively decreases (D) Calorific value of the coal increases

Description : Ratio of primary air to secondary air increases with increase in the rank of coal, because the (A) High rank coals have higher amount of volatile matter (B) Ratio of fixed carbon to volatile matter increases (C) Oxygen content progressively decreases (D) Calorific value of the coal increases

Last Answer : (B) Ratio of fixed carbon to volatile matter increases

Coke oven gas produced by high temperature carbonisation of coal (as compared to that produced by low temperature carbonisation), has (A) Higher calorific value (B) Lower hydrogen content (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Coke oven gas produced by high temperature carbonisation of coal (as compared to that produced by low temperature carbonisation), has (A) Higher calorific value (B) Lower hydrogen content (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

A coal having higher volatile matter content will necessarily have lower (A) Ash fusion temperature (B) Calorific value (C) Ignition temperature (D) Caking index

Description : A coal having higher volatile matter content will necessarily have lower (A) Ash fusion temperature (B) Calorific value (C) Ignition temperature (D) Caking index

Last Answer : (C) Ignition temperature