Rate of heat release in a furnace, which is the measure of heat intensity, is defined as (A) kcal/hr/m3 combustion space (B) kcal/m3 combustion space (C) kcal/hr (D) None of these

Rate of heat release in a furnace, which is the measure of heat intensity,
is defined as
(A) kcal/hr/m3 combustion space
(B) kcal/m3 combustion space
(C) kcal/hr
(D) None of these
by

1 Answer

Answer :

(A) kcal/hr/m3 combustion space
by

Related questions

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In a heat exchanger, one transfer unit means (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section (B) The size of the exchanger in which heat transfer rate is 1 kcal/hr (C) Both (A) and (B) (D) None of these

Description : In a heat exchanger, one transfer unit means (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section (B) The size of the exchanger in which heat transfer rate is 1 kcal/hr (C) Both (A) and (B) (D) None of these

Last Answer : (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section

One ton of refrigeration capacity is equivalent to the heat removal rate of (A) 50 kcal/hr (B) 200 BTU/hr (C) 200 BTU/minute

Description : One ton of refrigeration capacity is equivalent to the heat removal rate of (A) 50 kcal/hr (B) 200 BTU/hr (C) 200 BTU/minute

Last Answer : (C) 200 BTU/minute

What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Description : What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Last Answer : Overall efficiency

Heat load in a cooling tower (A) Means the amount of heat thrown away (KCal/hr.) by the cooling tower (B) Is equal to the number of kg, of water circulated times the cooling range (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Heat load in a cooling tower (A) Means the amount of heat thrown away (KCal/hr.) by the cooling tower (B) Is equal to the number of kg, of water circulated times the cooling range (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

Steam side heat transfer co-efficient in an evaporator is in the range of __________ kcal/hr.m2°C. (A) 10-50 (B) 100-500 (C) 1000-1500 (D) 5000-15000

Description : Steam side heat transfer co-efficient in an evaporator is in the range of __________ kcal/hr.m2°C. (A) 10-50 (B) 100-500 (C) 1000-1500 (D) 5000-15000

Last Answer : (D) 5000-15000

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity (C) In unsteady state heat conduction, heat flows in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Description : Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the ... in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Last Answer : (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Description : Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Last Answer : (A) Range of fuel firing rates

Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Description : Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30(C) 7 (D) 70

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Description : A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Last Answer : (A) Require smaller combustion chamber

Calorific value of pitch creosote mixture (PCM) i.e., C.T.F.-200 is about (A) 8800 kcal/m3 (B) 8800 kcal/kg (C) Same as that of coal middling (D) 25000 kcal/kg

Description : Calorific value of pitch creosote mixture (PCM) i.e., C.T.F.-200 is about (A) 8800 kcal/m3 (B) 8800 kcal/kg (C) Same as that of coal middling (D) 25000 kcal/kg

Last Answer : (B) 8800 kcal/kg

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

The benchmarking parameter for air conditioning equipment is a) kW/Ton of Refrigeration b) kW/ kg of refrigerant handled c) kcal/m3 of chilled water d) Differential temperature across chiller

Description : The benchmarking parameter for air conditioning equipment is a) kW/Ton of Refrigeration b) kW/ kg of refrigerant handled c) kcal/m3 of chilled water d) Differential temperature across chiller

Last Answer : kW/Ton of Refrigeration

The benchmarking parameter for air conditioning equipment is a) kW/Ton of Refrigeration b) kW/ kg of refrigerant handled c) kcal/m3 of chilled water d) Differential temperature across chiLLER

Description : The benchmarking parameter for air conditioning equipment is a) kW/Ton of Refrigeration b) kW/ kg of refrigerant handled c) kcal/m3 of chilled water d) Differential temperature across chiLLER

Last Answer : kW/Ton of Refrigeration

The benchmarking parameter for a vapour compression refrigeration system is a) kW / kg of refrigerant used b) kcal / m3 of chilled water c) BTU / Ton of Refrigeration d) kW / Ton of Refrigeration

Description : The benchmarking parameter for a vapour compression refrigeration system is a) kW / kg of refrigerant used b) kcal / m3 of chilled water c) BTU / Ton of Refrigeration d) kW / Ton of Refrigeration

Last Answer : d) kW / Ton of Refrigeration

In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Description : In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Last Answer : (C) Radiation of heat from the roof of the combustion chamber

Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Description : Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Last Answer : (A) Controlling the excess air

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ

Description : Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ

Last Answer : (A) 3.6 W.D.V.ρ

The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Last Answer : (A) 3.6 AVS.ρ

Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls in rotation per second (rps) D = diameter of rolls, m). (A) 3.6 V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Last Answer : (A) 3.6 V.W.Dr.ρ

Unit of mass velocity is (A) kg/hr (B) kg/m2 . hr (C) kg/m2 (D) kg/m3 . hr

Description : Unit of mass velocity is (A) kg/hr (B) kg/m2 . hr (C) kg/m2 (D) kg/m3 . hr

Last Answer : (B) kg/m2 . hr

1 BTU/hr.ft.°F is equal to __________ kcal/hr. m.°C. (A) 1.49 (B) 1 (C) 4.88 (D) None of these

Description : 1 BTU/hr.ft.°F is equal to __________ kcal/hr. m.°C. (A) 1.49 (B) 1 (C) 4.88 (D) None of these

Last Answer : (A) 1.49

Pick out the wrong statement: (A) With change in temperature, the radiant energy emitted by a black body remains unchanged (B) Absorptivity of a body approaches unity in case of diffuse reflection (C) Absorptivity of a perfectly black body is unity (D) Value of Stefan-Boltzmann constant is 4.876 × 10 -8 KCal/m2 .hr.°K4

Description : Pick out the wrong statement: (A) With change in temperature, the radiant energy emitted by a black body remains unchanged (B) Absorptivity of a body approaches unity in case of diffuse reflection (C) Absorptivity of ... unity (D) Value of Stefan-Boltzmann constant is 4.876 10 -8 KCal/m2 .hr.°K4

Last Answer : (A) With change in temperature, the radiant energy emitted by a black body remains unchanged

A BTU/hr.ft. 2 °F is equal to (A) 1 kcal/hr. m2°C (B) 4.88 kcal/hr. m. 2°C (C) 1 kcal/hr. m2 .°K (D) None of these

Description : A BTU/hr.ft. 2 °F is equal to (A) 1 kcal/hr. m2°C (B) 4.88 kcal/hr. m. 2°C (C) 1 kcal/hr. m2 .°K (D) None of these

Last Answer : (B) 4.88 kcal/hr. m. 2°C

What is the unit of thermal conductivity? (A) Kcal/hr. m2 °C (B) Kcal/hr.m.°C (C) Kcal/hr.m (D) Kcal/hr. °C

Description : What is the unit of thermal conductivity? (A) Kcal/hr. m2 °C (B) Kcal/hr.m.°C (C) Kcal/hr.m (D) Kcal/hr. °C

Last Answer : (B) Kcal/hr.m.°C

Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface between B and C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Last Answer : (C) 70

The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal(C) Accelerates the burning rate and economises on fuel combustion(D) All (A), (B) and (C)

Description : The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel combustion (D) All (A), (B) and (C)

Last Answer : (C) Accelerates the burning rate and economises on fuel combustion

Which of the following has the least calorific value (kcal/Nm3 )? (A) Blast furnace gas (B) Coke oven gas (C) Sewage gas (D) Natural gas

Description : Which of the following has the least calorific value (kcal/Nm3 )? (A) Blast furnace gas (B) Coke oven gas (C) Sewage gas (D) Natural gas

Last Answer : (A) Blast furnace gas

Calorific value of furnace oil is about __________ Kcal/kg. (A) 10,000 (B) 15,000 (C) 5,000 (D) 20,000

Description : Calorific value of furnace oil is about __________ Kcal/kg. (A) 10,000 (B) 15,000 (C) 5,000 (D) 20,000

Last Answer : (A) 10,000

Which of the following fuels has the highest calorific value per unit mass (kcal/kg)? (A) Coal (B) Kerosene (C) Natural gas (D) Furnace oil

Description : Which of the following fuels has the highest calorific value per unit mass (kcal/kg)? (A) Coal (B) Kerosene (C) Natural gas (D) Furnace oil

Last Answer : (D) Furnace oil

Calorific value of blast furnace gas is around __________ KCal/Nm3 . (A) 850 (B) 1800 (C) 4200 (D) 6500

Description : Calorific value of blast furnace gas is around __________ KCal/Nm3 . (A) 850 (B) 1800 (C) 4200 (D) 6500

Last Answer : (A) 850

Fuel' can be defined as a substance which produces heat by (A) Combustion (B) Nuclear fission (C) Nuclear fusion (D) All (A), (B) & (C)

Description : Fuel' can be defined as a substance which produces heat by (A) Combustion (B) Nuclear fission (C) Nuclear fusion (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C

One tonrefrigeration corresponds to (a) 50 kcal/min (b) 50 kcal/kr (c) 80 kcal/min (d) 80 kcal/hr

Description : One tonrefrigeration corresponds to (a) 50 kcal/min (b) 50 kcal/kr (c) 80 kcal/min (d) 80 kcal/hr

Last Answer : Ans: a

The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit conversion is 20%, then the exit temperature (in k) is (Data: Heat of reaction at 298 K = - 50000 kJ/ kmole of A reacted Heat capacities CPA = CPB = 100kJ/kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Description : The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit ... /kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Last Answer : (C) 600

One ton of refrigeration is not equivalent to the heat removal rate of (A) 200 BTU/minute (B) 50 kcal/minute (C) 50 kJ/sec (D) 3.5 KW

Description : One ton of refrigeration is not equivalent to the heat removal rate of (A) 200 BTU/minute (B) 50 kcal/minute (C) 50 kJ/sec (D) 3.5 KW

Last Answer : (C) 50 kJ/sec

In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace, producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 TPD GCV of coal : 4500 kcal/kg Power Purchased from Grid : 82400 kWh / day Specific Energy consumption for Kiln producing Sponge Iron: 120 kWh / ton sponge iron Calculate the following 1. Specific Energy Consumption of Induction melting furnace in terms of kWh/ton of molten steel 2. Specific Energy Consumption of the entire plant, in terms of kcal/kg of molten steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )

Description : In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace,  producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 ... molten  steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )

Last Answer :  a) Specific Energy Consumption of Induction Melting Furnace  Molten Steel Production from the Induction melting furnace per day  = 100 x 88/100 = 88 TPD Total Energy Consumption of the Plant = 82400 kWh ... mark c) Total Energy consumption of Plant in ToE  = 655864000/107  = 65.586 ToE

The intensity of active earth pressure at a depth of 10 metres in dry cohesionless sand with an angle of internal friction of 30° and with a weight of 1.8 t/m3 , is (A) 4 t/m2 (B) 5 t/m2 (C) 6 t/m2 (D) 7 t/m2

Description : The intensity of active earth pressure at a depth of 10 metres in dry cohesionless sand with an angle of internal friction of 30° and with a weight of 1.8 t/m3 , is (A) 4 t/m2 (B) 5 t/m2 (C) 6 t/m2 (D) 7 t/m2

Last Answer : Answer: Option C

Specific heating capacity of a furnace is expressed as (A) Weight heated/hr (B) Weight heated/furnace volume (C) Weight heated/hr/furnace volume (D) None of these

Description : Specific heating capacity of a furnace is expressed as (A) Weight heated/hr (B) Weight heated/furnace volume (C) Weight heated/hr/furnace volume (D) None of these

Last Answer : (C) Weight heated/hr/furnace volume