Draw symbol & V-I characteristics of (i) LASCR (ii) DIAC (iii) TRIAC

Draw symbol & V-I characteristics of (i) LASCR (ii) DIAC (iii) TRIAC
by

1 Answer

Answer :

(i) LASCR: 


image



(ii) DIAC: 


image


(iii) TRIAC: 


image

by

Related questions

Describe triggering circuit for TRIAC using DIAC.

Description : Describe triggering circuit for TRIAC using DIAC.

Last Answer : Triggering circuit for TRIAC using DIAC: DIAC stands for diode alternating current. It's a two terminal four layer bidirectional device. It conducts in both directions. DIAC is used for triggering TRIAC. ... of DIAC to the gate terminal of TRIAC reduces the harmonics.

Draw a symbol and neat labeling V-I characteristics of GTO and explain its operation.

Description : Draw a symbol and neat labeling V-I characteristics of GTO and explain its operation.

Last Answer : Ans: Symbol and V-I characteristics of GTO: Operation of GTO: i) As the applied anode to cathode voltage is increased above zero, very small current (leakage current) flows through the device. ... low voltage (VBRR). The reverse breakdown voltage is of the order of 20 to 30 volt only. 

Which of the following does not show non-linear V-I characteristics?

Description : Which of the following does not show non-linear V-I characteristics? (A) Schottky diode (B) Tunnel diode (C) Thermistor, at a fixed temperature (D) p-n Junction diode.

Last Answer : Which of the following does not show non-linear V-I characteristics? (A) Schottky diode (B) Tunnel diode (C) Thermistor, at a fixed temperature (D) p-n Junction diode.

Draw the symbol of GTO and TRIAC.

Description : Draw the symbol of GTO and TRIAC.

Last Answer : 1) GTO: 2) TRIAC: 

With neat sketch explain four modes of operation of a TRIAC?

Description : With neat sketch explain four modes of operation of a TRIAC? 

Last Answer : Modes of operation of a TRIAC: There are four different operating modes of TRIAC:  1) MT2 and gate are positive with respect to terminal MT1(Mode1) : Here terminal MT2 is positive ... junction P2-N2 is forward biased, current carriers are injected and therefore, the TRIAC is turned on. 

Speed control of the motor using TRIAC

Description : Speed control of the motor using TRIAC

Last Answer : Speed control of the motor using TRIAC:  This basic phase triggering circuit uses the triac in series with the motor across an AC sinusoidal supply. The variable resistor, VR1 is used ... meaning that it may not trigger at the exact same point for each positive and negative half cycle.

Compare SCR and TRIAC

Description : Compare SCR and TRIAC

Last Answer : SCR TRIAC It is an unidirectional device. It is a bidirectional device. It is turned-on by only positive gate current. It can be turned-on by either ... applications including lamp dimmer, heating control, zero voltage switched AC relay, small AC motor control etc.

SCR is more utilized as compared to Triac because it is

Description : SCR is more utilized as compared to Triac because it is

Last Answer : SCR is more utilized as compared to Triac because it is available with higher ratings

Can we use triac in multiquadrant chopper?

Last Answer : Yes, we can use triac in the multi-quadrant chopper.

Draw a neat labelling V-I characteristics of SCR and explain the region

Description : Draw a neat labelling V-I characteristics of SCR and explain the region

Last Answer : (i) Latching current: It is the minimum anode current required to maintain the SCR in the conduction state just after turn-on and the gate signal has been removed.  (ii) Holding current: It is the minimum anode current required to hold the conducting SCR in the ON state. 

can a DIAC conduct in both direction?

Last Answer : Yes DIAC can conduct in both direction.

what is DIAC?

Description : what is DIAC?

Last Answer : DIAC is a two terminal and four layer device most DIAC have three terminals. DIAC stands for diode for alternating current. It conducts in both direction. It is also used for triggering triac.

Draw the symbol of LED & photodiode.

Description : Draw the symbol of LED & photodiode. 

Last Answer : Symbol of LED & photodiode

What is TRIAC?

Description : What is TRIAC?

Last Answer : TRIAC Structure:  Operating Principle: A triac is a three terminal, five layer semiconductor device. It is equivalent to two separate SCRs connected in anti-parallel with gates common. ... for electric fans and other electric motors. v. Heating control vi. Zero voltage switched relay

Draw symbol of NPN and PNP transistors.

Description : Draw symbol of NPN and PNP transistors. 

Last Answer : symbol of NPN and PNP transistors

Define resistor and draw symbol of variable resistor.

Description : Define resistor and draw symbol of variable resistor.

Last Answer : Resistor: A resistor is an electrical component that limits or regulates the flow of electrical current in an electronic circuit. Symbol of variable resistor:   

Draw symbol of LED and explain it’s working principle.

Description : Draw symbol of LED and explain it’s working principle.

Last Answer : Construction of LED: The basic structure of LED is shown in fig.(a). The active region exists between the p and n regions. The light emerges from the active side in all the directions when electron hole-pairs ... fig.(c). In this way an LED emits light. This is the principle of operation of LED.

What is photodiode? Draw the symbol and explain operation of photodiode.

Description : What is photodiode? Draw the symbol and explain operation of photodiode. 

Last Answer : A photodiode is a light detector that converts light into an electrical current. A photodiode is a semi-conductor device, with a p-n junction and an intrinsic layer between p and n layers ... current is independent of reverse bias voltage. Reverse current is mostly depends on the light intensity.

Explain the electrical characteristics of transformer.

Description : Explain the electrical characteristics of transformer.

Last Answer : Transformer electrical characteristics: Area of primary and secondary conductors, Apri and Asec: Winding loss Pw: Flux density and core loss: Leakage inductance: ... transformer span. The rise in temperature may breakdown insulation which may cause failure of the transformer.

What are the desirable characteristics of ideal switch?

Description : What are the desirable characteristics of ideal switch?

Last Answer : Desirable characteristics of the ideal switch: It is desirable to have power switches characteristics closer to ideal switch. The ideal switch should have the following characteristics. Zero resistance when ... . 100% efficiency. Able to control power flow with zero power dissipation.

What is the symbol of a capacitor?

Description : What is the symbol of a capacitor?

Last Answer : symbol of a capacitor

What is the symbol for AC power?

Description : What is the symbol for AC power?

Last Answer : If you need to measure alternating current in a circuit, different multimeters have different symbols to measure it (and the corresponding voltage), usually "ACA" and "ACV," or "A" and "V" with a squiggly line (~) next to or above them.

what is gate turn off thyristor (GTO)?

Description : Draw the structural diagram of GTO. Explain briefly the switching behavior of GTO with the help of appropriate voltage and current waveform.

Last Answer : Gate Turn Off Thyristor (GTO) Conventional Thyristor can be turned on with gate terminal but can not turn off from gate terminal. But in case of Gate Turn Off Thyristor (GTO), we can turn it on and off ... subdivided as storage period (Ts), fall period (Tp) and tail period (Tt).

Diode VI characteristics

Description : Diode VI characteristics

Last Answer : Diode VI characteristics

basic characteristics of sound signal.

Description :  basic characteristics of sound signal.

Last Answer : Level and loudness: The amplitude of a sound wave determines its loudness or volume. A larger amplitude means a louder sound, and a smaller amplitude means a softer sound. The loudness of a ... the reproducing system should be capable of handling the maximum and minimum power in the same ratio. 

Compare characteristics of asynchronous and synchronous transmission mode.

Description : Compare characteristics of asynchronous and synchronous transmission mode (four points). 

Last Answer : Synchronous transmission Asynchronous transmission 1. Synchronous transmission are synchronized by an external clock. 1. Asynchronous transmission are synchronized by special signals along the transmission ... for transferring a small amount of data as it is simple and economical.

Explain the characteristics of solar cell.

Description : Explain the characteristics of solar cell.  

Last Answer : Characteristics of solar cell : Explanation :- Solar cells produce direct current ( DC ) electricity and current times voltage equals power, so we can create solar cell I-V curves representing ... system so that it can operate as close to its optimal peak power point (MPP) as possible.

State characteristics of force.

Description : State characteristics of force.

Last Answer : i) Magnitude: The quantity of force e.g. 10 N, 100 kN etc.  ii) Direction: It is the line along which the force acts. It is also called as line of action of the force.  iii) Point of ... .  Push: If the arrow head is pointed towards the point of application, the nature of the force is push.

What is the smallest unit of a compound with the same chemical characteristics?

Description : What is the smallest unit of a compound with the same chemical characteristics?

Last Answer : The molecule is the smallest unit of a compound with the same chemical characteristics.

The following is/are the characteristics of SF6 circuit breakers:

Description : The following is/are the characteristics of SF6 circuit breakers:  (A) It does not need an auxiliary breaking chamber (B) Short break time of 2 to 2.5 cycles (C) All of the above (D) None of the above

Last Answer : The following is/are the characteristics of SF6 circuit breakers:  (A) It does not need an auxiliary breaking chamber (B) Short break time of 2 to 2.5 cycles (C) All of the above (D) None of the above

The terminal characteristics of a dc generator suitable for electric welders is

Description : The terminal characteristics of a dc generator suitable for electric welders is (A) separately excited generator (B) shunt generator (C) series generator (D) differentially compounded generator

Last Answer : The terminal characteristics of a dc generator suitable for electric welders is differentially compounded generator

The desirable static characteristics of a measuring system are?

Last Answer : The desirable static characteristics of a measuring system are accuracy, sensitivity and reproducibility.

The speed/load characteristics of a universal motor is same as that of?

Last Answer : The speed/load characteristics of a universal motor is same as that of D.C. series motor.

What are some symbols associated with Persephone?

Description : What are some symbols associated with Persephone?

Last Answer : Persephone.

Figure 'D' shown in the illustration represents a/an ____________. EL-0078 A. DIP IC chip B. integrated diac/triac envelope C. TO-5 flat pack D. 7-segment BCD display

Description : Figure 'D' shown in the illustration represents a/an ____________. EL-0078 A. DIP IC chip B. integrated diac/triac envelope C. TO-5 flat pack D. 7-segment BCD display

Last Answer : Answer: A

Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Last Answer : i)Tray dryer:   ii)Plate column:    iii)Packed column:   iv) Jaw crusher:   v) Stirrer:   vi) Ball mill  

Draw the V-I characteristics of power transistor.

Description : Draw the V-I characteristics of power transistor. 

Last Answer : V-I characteristics of power transistor:

The symbol in figure 'A' shown in the illustration represents a ____________. EL-0065 A. diac B. field effect transistor C. silicon controlled rectifier D. unijunction transistor

Description : The symbol in figure 'A' shown in the illustration represents a ____________. EL-0065 A. diac B. field effect transistor C. silicon controlled rectifier D. unijunction transistor

Last Answer : Answer: D

Triac are usually operated at:

Description : Triac are usually operated at:

Last Answer : Triac are usually operated at: power frequency

A triac is a device which acts as a

Description : A triac is a device which acts as a  A) Diode in forward direction and thrylistor in the reverse direction B) Thyristor in both directions C) Diode in both directions D) Thyristor in forward direction and diode in reverse direction

Last Answer : A triac is a device which acts as a Thyristor in both directions

Draw Conventional symbol for i) Embankment ii) Pond or Lake iii) Tunnel iv) Compound Wall

Description : Draw Conventional symbol for i) Embankment ii) Pond or Lake iii) Tunnel iv) Compound Wall

Last Answer : Conventional symbol for i) Embankment ii) Pond or Lake iii) Tunnel iv) Compound Wall

Draw conventional symbol for: i. Cutting ii. Road with bridge iii. Orchard iv. river

Description : Draw conventional symbol for: i. Cutting ii. Road with bridge iii. Orchard iv. river

Last Answer : conventional symbol for: i. Cutting ii. Road with bridge iii. Orchard iv. river

Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Description : Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Last Answer :  Iron core inductor:  Ferrite core inductor:  

Draw the ray diagram in each case to show the position and nature of the image formed when the object is placed: (i) at the centre of curvature of a concave mirror (ii) between the pole P and focus F of a concave mirror (iii) in front of a convex mirror (iv) at 2F of a convex lens (v) in front of a concave lens -Physics

Description : Draw the ray diagram in each case to show the position and nature of the image formed when the object is placed: (i) at the centre of curvature of a concave mirror (ii) between the pole P and focus F of ... front of a convex mirror (iv) at 2F of a convex lens (v) in front of a concave lens -Physics

Last Answer : Answer. Nature of image: Real, inverted and same size image is formed at the centre of curvature. Nature of image: Virtual, enlarged and erect image is formed behind the mirror. Nature of image: Virtual ... : Virtual, erect and diminished image is formed between O and F on the same side of object.

Which of the following characteristics represent ‘inheritance of blood groups’ in humans? (i) Dominance (ii) Co-dominance (iii)Multiple allele (iv) Incomplete dominance (v) Polygenic inheritance (a) (ii), (iii) and (v) (b) (i), (ii) and (iii) (c) (ii), (iv) and (v) (d) (i), (iii) and (v)

Description : Which of the following characteristics represent ‘inheritance of blood groups’ in humans? (i) Dominance (ii) Co-dominance (iii)Multiple allele (iv) Incomplete dominance (v) Polygenic inheritance (a) (ii), (iii) and (v) (b) (i), (ii) and (iii) (c) (ii), (iv) and (v) (d) (i), (iii) and (v)

Last Answer : (b) (i), (ii) and (iii)

Which of the following characteristics of constructor are true. i) They should be declared in the public section. ii) They are invoked automatically when the objects are created. iii) They do not have return type and void also. iv) We cannot refer their address. v) Constructors cannot virtual. A) Only i, ii, iii and v B) Only ii, iii, iv, and v C) Only i, iii, iv and v D) All i, ii, iii, iv and v

Description : Which of the following characteristics of constructor are true. i) They should be declared in the public section. ii) They are invoked automatically when the objects are created. iii) They do not have return type and void also. ... and v C) Only i, iii, iv and v D) All i, ii, iii, iv and v

Last Answer : D) All i, ii, iii, iv and v

Match List-I (Type of Unemployment) with List-II (Characteristics) and select the correct answer using the codes given below: L ist-I L ist -I I (Type of (Char acter ist ics) Unem ployment ) A. Seasonal I. Occurs during boom or recession in the economy B. Frictional II. An absence of demand for a certain type of workers C. Disguised III. Occurs when moving from one job to another D. Structural IV. Actual contribution by the additional labour is nil E. Cyclical V. Job opportunities during certain months in the year

Description : Match List-I (Type of Unemployment) with List-II (Characteristics) and select the correct answer using the codes given below: L ist-I L ist -I I (Type of (Char acter ist ics) Unem ... contribution by the additional labour is nil E. Cyclical V. Job opportunities during certain months in the year

Last Answer : (1) A-V, B-III, C-IV, D-II, E-I