Description : Ball bearings are used in cycles, scooters etc. to _____. A. Reduce the friction between the wheel and the axle B. Increase the friction between the wheel and the axle C. Reduce the friction between ground and the wheel D. None of these
Last Answer : ANSWER: A
Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links
Last Answer : d) Between two lower links
Description : Is my 2016 Chrysler Town and Country front or rear wheel drive?
Last Answer : A 2016 Chrysler Town and Country is front wheel drive.
Description : pressure should be less in rear wheel as compare to front wheel because of a) high traction b) low draft c) high draft d) none of these Ans. a
Last Answer : ans a
Description : Handbrake is applicable to A. Only front wheels B. Only rear wheels C. Both front and rear wheel. D. All of the above.
Last Answer : B. Only rear wheels
Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts
Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout
Description : What size socket do you need to change the wheel bearings on 1998 GMC Jimmy front and back axles?
Last Answer : Need to know if 2 wheel or 4 wheel drive for the front. Eitherway, there is no nut on the back axles.
Description : Draw a neat of full floating rear axle. Label all the parts. State an application of Semi floating, three quarter floating and full floating rear axle.
Last Answer : Semi floating: light motor vehicle three quarter floating:light motor vehicle full floating rear axle: heavy commercial vehicles
Description : What is the final ratio of the rear axle of the Jaguar XJ6 year 1976?
Last Answer : he Jaguar XJ is a series of full-size luxury cars produced by British automobile manufacturer The original model was the last Jaguar saloon to have had the input of Sir The first-generation of the XJ ... period of 24 years, with the full length of the bumper with embedded turn signals at each end.
Description : What is the final ratio of the rear axle of the Ford F-850 Truck year 1967?
Last Answer : To start with , the Ford Super Duty F-650 was one of the biggest trucks in the Ford F-series line.
Description : The tie rod connects the front wheel spindle arms and is actuated by the steering shaft through a) chain link b) gear link c) tension link d) drag link
Last Answer : d) drag link
Description : 88 firebird rear axle comes out w/new brng and retainer. What causes this
Last Answer : Need Answer
Description : Why is backlash used in rear axle?
Last Answer : Need answer
Description : How do you remove rear axle from 05 Suzuki Ltz 250 ATV?
Last Answer : What is the answer ?
Description : Describe a method of lubrication for rear axle assembly of the truck.
Last Answer : The combined lubrication system is very important in the final drive axle, where load and or speed transferred are high, the combination of splash and force feed of lubricant is delivered to ... trickles down due to gravity into the sump, where it is collected again and the cycle repeats
Description : State the loads acting on the rear axle.
Last Answer : The various loads acting on the rear axle are- 1) Driving thrust-Driving torque produced in the engine causes the thrust to be produced in the road wheels, which has to be transmitted from the ... a beam supported at ends loaded. This weight causes bending and shears force in the axle shaft.
Description : Molybdenum steels containing 0.15 to 0.40% molybdenum (A) Are prone to temper brittleness (B) Are used for automobile parts like gears, axle, shaft, bearings etc. (C) Have very poor fatigue resistance
Last Answer : (B) Are used for automobile parts like gears, axle, shaft, bearings etc
Description : Is a screwdriver a kind of wheel and axle?
Description : What equation would you to calculate the ideal mechanical advantage of a wheel and axle if the input force is on the axle?
Last Answer : Feel Free to Answer
Description : Is an example of a device that uses a wheel a device that uses a wheel and axle?
Description : Why is a skateboard a wheel and axle?
Last Answer : bum
Description : Where is the wheel and axle plant of Indian Railways situated? A. Hydrabad B. Bangalore C. Mumbai D. Jamshedpur
Last Answer : B [Bangalore] Explanation: Rail Wheel Factory, Yelehanka (RWF) (also known as Wheel and Axle Plant) is a manufacturing unit of Indian Railways, producing wheels, axles and wheel sets of ... for the use of Indian Railways and overseas customers is situated at Yelahanka, Bangalore in the Indian
Description : Design of highways is based on (A) Axle loads (B) Axle spacings (C) Wheel bases (D) All the above
Last Answer : Answer: Option D
Description : In disc brake, the disc is attached to the (A) wheel (B) axle (C) suspension system (D) none of the above
Last Answer : (B) axle
Description : Inflation pressure in the rear wheels of the tractor varies between a) 0.5 to 1.2 kg/cm2 b) 8 to 1.2 kg/cm2 c) 2 to 1.5 kg/cm2 d) 1.5 to 20 kg/cm2
Last Answer : b) 8 to 1.2 kg/cm2
Description : The bearings which resist radial loads is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing
Last Answer : d) journal bearing
Description : Under normal operating conditions, the bearings are filled with the proper type of lubricant after every hours of working about a) 6 hours b) 8 hoursc) 10 hours d) 12 hours
Last Answer : c) 10 hours
Description : Greasing of bearings of Steel girder bridges is done once in years.
Last Answer : Three
Description : how to replace the front axle on a 1999 nissan sentra
Description : what is the torque setting for front axle on 05 Ford 4x2?
Last Answer : The setting would be around 7 route in order to have a correct setting of axle.
Description : State functions and materials for front axle. Draw proportionate diagram of front axle showing cross-section at different positions.
Last Answer : The functions of front axle : 1) It supports the weight of front part of the vehicle. 2) It facilitates steering. 3) It absorbs shocks which are transmitted due to road surface irregularities. 4) It ... is usually a steel drop forging having 0.4 % carbon steel or 1-3 % nickel steel.
Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END-AFT END, Top .045 - .049, Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.
Last Answer : Answer: A
Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END -AFT END, Top .045 - .049 , Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.
Description : The back wheel of the Favorit has blocked and is not moving.
Last Answer : Take a log about 30 cm long with a diameter of 2-3 cm. (eg a long extension from the Gola set) Lean it against the brake drum through a hole in the disc and tap it with a larger hammer. ... The brake will release at 90 percent. All this on a car with the parking brake enabled and number one engaged.
Description : Explain Bicycle Rear Wheel Sprocket Working?
Last Answer : Rear wheel sprocket works under the principle of ratchet and pawl.
Description : Where can I get new wheel bearings?
Last Answer : The best place to get any auto parts or wheel bearings is from your auto car dealer, or Canadian tire they should have you wanted. From what I gather no prices were posted online.
Description : The function of ball bearings in a wheel is – (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience
Last Answer : (2) to convert kinetic friction into rolling friction Explanation: A ball bearing is a type of rollingelement bearing that uses balls to maintain the separation between the bearing races. The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads.
Description : When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar
Last Answer : Answer: C
Description : The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer
Last Answer : Answer: B
Description : The function of ball bearings in a wheel is : (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience
Last Answer : to convert kinetic friction into rolling friction
Description : The scheme of mobile food testing laboratory called “Food safety on wheel”has been rolled out by a.ICAR b.FSSAI c.NABARD d.AGMARK
Last Answer : b.FSSAI
Description : there are 3 light bulbs in three seperate rooms. in front of you, there is a panel with 3 seperate switches. they only turn on or off. you may look inside each room only once. how can you tell which bulb belongs to which switch? -Riddles
Last Answer : you turn on any two switches, leave them for a few minutes, and turn one off. you enter each room only once. you know that the lightbulb that is lit beongs to the switch that was left on, the ... hot, belongs to the switch you turned off, and the cold bulb belongs to the switch you never touched.
Description : When I box up my bike to ship, do I have to remove the front and rear racks?
Last Answer : I would look for info on that with the shipping service you’ll use.
Description : why does adjusting the camber in the front and rear of your car enable race tires to last longer? I race a Porsche 911 and am hearing differing things about the benifits of camber settings.
Last Answer : race tires are usually made of a softer rubber than normal street tires to enable better traction. changing the camber changes the weight distribution of the vehicle over the tire - and given that the ... sure that the right amount of pressure is being put on the tire to prevent uneven wear...
Description : Do Front air bags are not designed to offer protection from crashes from the rear and side?
Description : What states require front & rear license plate installation on cars?
Last Answer : All states EXCEPT: Alabama, Arizona, Arkansas, Delaware, Florida, Georgia, Indiana, Kansas, Kentucky, Louisiana, Michigan, Mississippi, New Mexico, North Carolina, Oklahoma, Pennsylvania, South Carolina, Tennessee, and West Virginia
Description : Is a front or rear window tint illegal anywhere in the United States?
Last Answer : Front windows tint is illegal is most states in the US. You can though get a permit that allows it with a prescription from a doctor saying you have sensitive eyes. See the website http://home ... in some of the states in the United States. Such states include Chicago, New York and Massachusetts.
Description : how much would it cost to replace the front brake pads and rear drums on a 2001 honda odesey?
Last Answer : You have to make at least enough to pay your portion of the rent when you are on Section 8. But you cannot make no more than $28,250 for a family of four to remain on the program.
Description : Whats the cost to replace front and rear brakes on a 2017 chevy sonic?
Last Answer : Search Results Featured snippet from the web Chevrolet Sonic Brake Rotors/Discs Replacement costs $329 on average. Car Service Estimate 2017 Chevrolet SonicL4-1.8L Service typeBrake Rotor/Disc - ... 2017 Chevrolet SonicL4-1.4L Turbo Service typeBrake Rotor/Disc - Front Replacement Estimate$413.07
Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature