. Boiling point elevation for a strong and concentrated solution is found by Duhring's rule, which states that at the same pressure, the boiling point of a solution is a linear function of the __________ of pure water. (A) Boiling point (B) Dynamic viscosity (C) Kinematic viscosity (D) Density

. Boiling point elevation for a strong and concentrated solution is found
by Duhring's rule, which states that at the same pressure, the boiling point
of a solution is a linear function of the __________ of pure water.
(A) Boiling point
(B) Dynamic viscosity
(C) Kinematic viscosity
(D) Density
by

1 Answer

Answer :

(A) Boiling point
by

Related questions

Boiling point of a solution according to Duhring's rule is a linear function of the __________ of water. (A) Boiling point (at the same pressure) (B) Viscosity (C) Density (D) Thermal conductivity

Description : Boiling point of a solution according to Duhring's rule is a linear function of the __________ of water. (A) Boiling point (at the same pressure) (B) Viscosity (C) Density (D) Thermal conductivity

Last Answer : (A) Boiling point (at the same pressure)

. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

The kinematic viscosity (in stoke) and the absolute/dynamic viscosity (in poise) are the same for __________ at room temperature. (A) Air (B) Water (C) Mercury (D) Alcohol

Description : The kinematic viscosity (in stoke) and the absolute/dynamic viscosity (in poise) are the same for __________ at room temperature. (A) Air (B) Water (C) Mercury (D) Alcohol

Last Answer : (B) Water

Dimension of mass diffusivity is the same as that of (A) Kinematic viscosity (B) Dynamic viscosity (C) Surface tension (D) Pressure

Description : Dimension of mass diffusivity is the same as that of (A) Kinematic viscosity (B) Dynamic viscosity (C) Surface tension (D) Pressure

Last Answer : (A) Kinematic viscosity

Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in the tubes of natural circulation evaporators is in the range of 0.3 to 0.9 metre/second (C) Duhring's plot is used for calculating the concentration of solution (D) In a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Description : Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in ... a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Last Answer : (C) Duhring's plot is used for calculating the concentration of solution

12. Kinematic viscosity is the product of dynamic viscosity and the density of the liquid. A) Yes B) No

Description : 12. Kinematic viscosity is the product of dynamic viscosity and the density of the liquid. A) Yes B) No

Last Answer : B

Kinematic viscosity is equal to (A) Dynamic viscosity/density (B) Dynamic viscosity × density (C) Density/dynamic viscosity (D) 1/dynamic viscosity × density

Description : Kinematic viscosity is equal to (A) Dynamic viscosity/density (B) Dynamic viscosity × density (C) Density/dynamic viscosity (D) 1/dynamic viscosity × density

Last Answer : Answer: Option A

Choose the correct relationship (A) Specific gravity = gravity × density (B) Dynamic viscosity = kinematic viscosity × density (C) Gravity = specific gravity × density (D) Kinematic viscosity = dynamic viscosity × density

Description : Choose the correct relationship (A) Specific gravity = gravity × density (B) Dynamic viscosity = kinematic viscosity × density (C) Gravity = specific gravity × density (D) Kinematic viscosity = dynamic viscosity × density

Last Answer : Answer: Option B

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

N. second/m2 is (A) The S.I. unit of dynamic viscosity (B) The S.I. unit of kinematic viscosity (C) Equivalent to one poise (D) Equivalent to one stoke

Description : N. second/m2 is (A) The S.I. unit of dynamic viscosity (B) The S.I. unit of kinematic viscosity (C) Equivalent to one poise (D) Equivalent to one stoke

Last Answer : (A) The S.I. unit of dynamic viscosity

The capacity of double-effect evaporator is less than half of the capacity of two single effects, each of which is operating over same terminal temperature difference, when the (A) Solution has an elevation of boiling point (B) Evaporators operate under vacuum (C) Evaporators operate at atmospheric pressure (D) None of these

Description : The capacity of double-effect evaporator is less than half of the capacity of two single effects, each of which is operating over same terminal temperature difference, when the (A) Solution has ... B) Evaporators operate under vacuum (C) Evaporators operate at atmospheric pressure (D) None of these

Last Answer : (A) Solution has an elevation of boiling point

Stoke is the unit of (A) Kinematic viscosity in C. G. S. units (B) Kinematic viscosity in M. K. S. units (C) Dynamic viscosity in M. K. S. units (D) Dynamic viscosity in S. I. units

Description : Stoke is the unit of (A) Kinematic viscosity in C. G. S. units (B) Kinematic viscosity in M. K. S. units (C) Dynamic viscosity in M. K. S. units (D) Dynamic viscosity in S. I. units

Last Answer : Answer: Option A

The dimension of diffusivity is same as that of the (A) Density (B) Molal concentration (C) Kinematic viscosity (D) Velocity head

Description : The dimension of diffusivity is same as that of the (A) Density (B) Molal concentration (C) Kinematic viscosity (D) Velocity head

Last Answer : (C) Kinematic viscosity

Kinematic viscosity is dependent upon (A) Pressure (B) Distance (C) Density (D) Flow

Description : Kinematic viscosity is dependent upon (A) Pressure (B) Distance (C) Density (D) Flow

Last Answer : Answer: Option C

Boiling point elevation of a solution of NaOH (A) Increases rapidly with temperature rise (B) Is almost independent of temperature (C) Is almost independent of pressure (D) Both (B) and (C)

Description : Boiling point elevation of a solution of NaOH (A) Increases rapidly with temperature rise (B) Is almost independent of temperature (C) Is almost independent of pressure (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Boiling point elevation of an ideal solution (A) Increases rapidly with temperature rise (B) Decreases rapidly with temperature rise (C) In independent of pressure (D) Both (B) and (C)

Description : Boiling point elevation of an ideal solution (A) Increases rapidly with temperature rise (B) Decreases rapidly with temperature rise (C) In independent of pressure (D) Both (B) and (C)

Last Answer : (A) Increases rapidly with temperature rise

The co-efficient of performance (COP) of a refrigerating system, which is its index of performance, is defined as the ratio of useful refrigeration to the net work. The units of __________ and COP are the same. (A) Kinematic viscosity (B) Work (C) Temperature (D) None of these

Description : The co-efficient of performance (COP) of a refrigerating system, which is its index of performance, is defined as the ratio of useful refrigeration to the net work. The units of __________ and COP are the same. (A) Kinematic viscosity (B) Work (C) Temperature (D) None of these

Last Answer : (D) None of these

Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Description : Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Last Answer : (A) Mass transfer co-efficient

Duhring’s rule is important in solving problems on (A) Distillation (B) Crystallisation (C) Evaporation (D) Humidification

Description : Duhring’s rule is important in solving problems on (A) Distillation (B) Crystallisation (C) Evaporation (D) Humidification

Last Answer : (C) Evaporation

The kinematic viscosity is the (A) Ratio of absolute viscosity to the density of the liquid (B) Ratio of density of the liquid to the absolute viscosity (C) Product of absolute viscosity and density of the liquid (D) Product of absolute viscosity and mass of the liquid

Description : The kinematic viscosity is the (A) Ratio of absolute viscosity to the density of the liquid (B) Ratio of density of the liquid to the absolute viscosity (C) Product of absolute viscosity and density of the liquid (D) Product of absolute viscosity and mass of the liquid

Last Answer : Answer: Option A

The ratio of absolute viscosity to mass density is known as (A) Specific viscosity (B) Viscosity index (C) Kinematic viscosity (D) Coefficient of viscosity

Description : The ratio of absolute viscosity to mass density is known as (A) Specific viscosity (B) Viscosity index (C) Kinematic viscosity (D) Coefficient of viscosity

Last Answer : Answer: Option C

Diffusion in concentrated solutions differs from that in dilute solutions, because of the change in the __________ with the concentration of the solution. (A) Degree of ideality (B) Viscosity (C) Both 'a '& 'b' (D) Neither 'a' nor 'b'

Description : Diffusion in concentrated solutions differs from that in dilute solutions, because of the change in the __________ with the concentration of the solution. (A) Degree of ideality (B) Viscosity (C) Both 'a '& 'b' (D) Neither 'a' nor 'b'

Last Answer : (C) Both 'a '& 'b

Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The boiling point of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Description : Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The ... of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Last Answer : (B) Filmwise condensation takes place on non-wettable surfaces

The ratio of kinematic viscosity to thermal diffusivity is called the __________ number. (A) Peclet (B) Prandtl (C) Stanton (D) Nusselt

Description : The ratio of kinematic viscosity to thermal diffusivity is called the __________ number. (A) Peclet (B) Prandtl (C) Stanton (D) Nusselt

Last Answer : (B) Prandtl

Which of the following is not dimension-less? (A) Froude number (B) Kinematic viscosity (C) Pressure co-efficient (D) None of these

Description : Which of the following is not dimension-less? (A) Froude number (B) Kinematic viscosity (C) Pressure co-efficient (D) None of these

Last Answer : (B) Kinematic viscosity

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Which of the following is not a dimension-less parameter? (A) Pressure-co-efficient (B) Froude number (C) Kinematic viscosity (D) Weber number

Description : Which of the following is not a dimension-less parameter? (A) Pressure-co-efficient (B) Froude number (C) Kinematic viscosity (D) Weber number

Last Answer : (C) Kinematic viscosity

Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than that of the damp material (C) Ratio of its capacity to economy equals the steam consumption in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Description : Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than ... in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Last Answer : (B) Thermal conductivity of a dry material is more than that of the damp material

Which of the following has the same dimension as mass diffusivity? (A) Momentum flux (B) Kinematic viscosity (C) Thermal diffusivity (D) Both (B) and (C)

Description : Which of the following has the same dimension as mass diffusivity? (A) Momentum flux (B) Kinematic viscosity (C) Thermal diffusivity (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, Vg = velocity gradient). (A) V2 (B) 1/V2 (C) 1/Vg (D) Vg

Description : Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, Vg = velocity gradient). (A) V2 (B) 1/V2 (C) 1/Vg (D) Vg

Last Answer : Option D

Which of the following properties is lower for a solution than for the pure solvent? w) osmotic pressure x) vapor pressure y) temperature z) boiling point

Description : Which of the following properties is lower for a solution than for the pure solvent? w) osmotic pressure x) vapor pressure y) temperature z) boiling point

Last Answer : ANSWER: X -- VAPOR PRESSURE

Which of the following properties is greater for a solution than for the pure solvent? w) freezing point x) vapor pressure y) temperature z) boiling point

Description : Which of the following properties is greater for a solution than for the pure solvent? w) freezing point x) vapor pressure y) temperature z) boiling point

Last Answer : ANSWER: D -- BOILING POINT

The intensive properties are (A) Molar volume, density, viscosity and boiling point (B) Refractive index and surface tension (C) Both (A) and (B) (D) None of these

Description : The intensive properties are (A) Molar volume, density, viscosity and boiling point (B) Refractive index and surface tension (C) Both (A) and (B) (D) None of these

Last Answer : (C) Both (A) and (B)

Relative to the pure solvent, the boiling point of a solution is: w) higher x) lower y) at the same temperature

Description : Relative to the pure solvent, the boiling point of a solution is: w) higher x) lower y) at the same temperature

Last Answer : ANSWER: W -- HIGHER

Alcohol is more volatile than water because ______ is lower than water. (1) its boiling point (2) its density (3) its viscosity (4) its surface tension

Description : Alcohol is more volatile than water because ______ is lower than water. (1) its boiling point (2) its density (3) its viscosity (4) its surface tension

Last Answer : (1) its boiling point Explanation: Drinking alcohol (ethanol) and a lot of other simple alcohols are more volatile than water because they are less polar. Thus, alcohol has higher vapor pres-sure and ... C is what makes it possible to distill alcohol into a much stronger solution than wine or beer.

Alcohol is more volatile than water because _________ is lower than water. (1) its boiling point (2) its density (3) its viscosity (4) its surface tension

Description : Alcohol is more volatile than water because _________ is lower than water. (1) its boiling point (2) its density (3) its viscosity (4) its surface tension

Last Answer : its boiling point

Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Description : Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Last Answer : (D) All geometrical, dynamic and kinematic similarity

Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature (C) Double pipe heat exchangers are mostly used in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Description : Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat ... in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Last Answer : (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature

The drag co-efficient for a bacterium moving in water at 1 mm/s, will be of the following order of magnitude (assume size of the bacterium to be 1 micron and kinematic viscosity of water to be 10 -6m2 /s). (A) 24000 (B) 24 (C) 0.24(D) 0.44

Description : The drag co-efficient for a bacterium moving in water at 1 mm/s, will be of the following order of magnitude (assume size of the bacterium to be 1 micron and kinematic viscosity of water to be 10 -6m2 /s). (A) 24000 (B) 24 (C) 0.24(D) 0.44

Last Answer : (D) 0.44

Diffusivity in concentrated solutions differs from that in dilute solutions, because of the changes in (A) Viscosity with concentration (B) Degree of ideality of the solution (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Diffusivity in concentrated solutions differs from that in dilute solutions, because of the changes in (A) Viscosity with concentration (B) Degree of ideality of the solution (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

. One stoke (unit of kinematic viscosity) is equivalent to (A) 1 cm2 /second (B) 1 m2 /second (C) 1 gm/cm. second (D) 1 kg. m/second

Description : . One stoke (unit of kinematic viscosity) is equivalent to (A) 1 cm2 /second (B) 1 m2 /second (C) 1 gm/cm. second (D) 1 kg. m/second

Last Answer : (A) 1 cm2 /second

Which of the following is a dimensionless parameter? (A) Angular velocity (B) Specific weight (C) Kinematic viscosity (D) None of these

Description : Which of the following is a dimensionless parameter? (A) Angular velocity (B) Specific weight (C) Kinematic viscosity (D) None of these

Last Answer : (D) None of these

The dimension of kinematic viscosity is(A) ML -2T -1 (B) L 2T -1 (C) ML -2T -2 (D) None of these

Description : The dimension of kinematic viscosity is (A) ML -2T -1 (B) L 2T -1 (C) ML -2T -2 (D) None of these

Last Answer : (B) L 2T -1

The boiling points of pure components of a binary system __________ with increase in total pressure of the system. (A) Decreases (B) Increases (C) Remains unchanged (D) May increase or decrease, depends on the system

Description : The boiling points of pure components of a binary system __________ with increase in total pressure of the system. (A) Decreases (B) Increases (C) Remains unchanged (D) May increase or decrease, depends on the system

Last Answer : (B) Increases

The driving potential for the crystal growth during crystallisation is the __________ of the solution. (A) Concentration (B) Viscosity (C) Super-saturation (D) Density

Description : The driving potential for the crystal growth during crystallisation is the __________ of the solution. (A) Concentration (B) Viscosity (C) Super-saturation (D) Density

Last Answer : (C) Super-saturation

Frictional force encountered after commencement of motion is called (A) Post friction (B) Limiting friction (C) Kinematic friction (D) Dynamic friction

Description : Frictional force encountered after commencement of motion is called  (A) Post friction  (B) Limiting friction  (C) Kinematic friction  (D) Dynamic friction 

Last Answer : (D) Dynamic friction 

On addition of solute in the solvent, the __________ of the solution decreases. (A) Boiling point (B) Freezing point (C) Vapour pressure (D) Both (B) and (C)

Description : On addition of solute in the solvent, the __________ of the solution decreases. (A) Boiling point (B) Freezing point (C) Vapour pressure (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

In a multiple effect evaporator, the effect of boiling point elevation is to (A) Reduce the capacity (B) Reduce the economy (C) Increase the economy (D) None of these

Description : In a multiple effect evaporator, the effect of boiling point elevation is to (A) Reduce the capacity (B) Reduce the economy (C) Increase the economy (D) None of these

Last Answer : (A) Reduce the capacity

The unit of kinematic viscosity in S. I. units is (A) N-m/s (B) N-s/m2 (C) m 2 /s (D) N-m

Description : The unit of kinematic viscosity in S. I. units is (A) N-m/s (B) N-s/m2 (C) m 2 /s (D) N-m

Last Answer : Answer: Option C

Which of the following is the unit of kinematic viscosity? (A) Pascal (B) Poise (C) Stoke (D) Faraday

Description : Which of the following is the unit of kinematic viscosity? (A) Pascal (B) Poise (C) Stoke (D) Faraday

Last Answer : Answer: Option C