What are the three stages through which PLL operates?

What are the three stages through which PLL operates?
by

1 Answer

Answer :

1.Free running

2.Capture

3.Locked/ tracking
by

Related questions

Which of the following is the basic synthesizer circuit? A. Frequency divider B. Frequency multiplier C. PLL D. Mixer

Description : Which of the following is the basic synthesizer circuit? A. Frequency divider B. Frequency multiplier C. PLL D. Mixer

Last Answer : C. PLL

Mention some typical applications of PLL

Description : Mention some typical applications of PLL

Last Answer : • Frequency multiplication/division • Frequency translation • AM detection • FM demodulation • FSK demodulation.

What is the purpose of having a low pass filter in PLL?

Description : What is the purpose of having a low pass filter in PLL?

Last Answer : *It removes the high frequency components and noise. *Controls the dynamic characteristics of the PLL such as capture range, lock-in range,band-width and transient response. *The charge on the filter capacitor gives a short- time memory to the PLL

Define capture range of PLL.

Description : Define capture range of PLL.

Last Answer : The range of frequencies over which the PLL can acquire lock with an input signal is called the capture range. It is expressed as a percentage of the VCO free running frequency.

Define lock-in range of a PLL.

Description : Define lock-in range of a PLL.

Last Answer : The range of frequencies over which the PLL can maintain lock with the incoming signal is called the lock-in range or tracking range. It is expressed as a percentage of theVCO free running frequency.

Mention some areas where PLL is widely used.

Description : Mention some areas where PLL is widely used.

Last Answer : 1.Radar synchronizations 2. Satellite communication systems 3. Air borne navigational systems 4. FM communication systems 5.Computers.

List the basic building blocks of PLL

Description : List the basic building blocks of PLL

Last Answer : 1.Phase detector/comparator 2.Low pass filter 3.Error amplifier 4.Voltage controlled oscillator

What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Description : What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Last Answer : A. Twisted pair

A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Description : A satellite transmitter operates at 4GHz with an antenna gain of 4dBi. The receiver 40000 km away has an antenna gain of 50 dBi. If the transmitter has a power of 8 W, find (ignoring feedline losses and mismatch) the EIRP in dBW. A. 50 B. 69 C. 49 D. 30

Last Answer : C. 49

The final power amplifier in an FM transmitter usually operates class ______. A. AB B. C C. B D. A

Description : The final power amplifier in an FM transmitter usually operates class ______. A. AB B. C C. B D. A

Last Answer : B. C

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

Fiber optic cable operates near _______ frequencies. A. 800 THz B. 20 MHz C. 200 MHz D. 2 GHz

Description : Fiber optic cable operates near _______ frequencies. A. 800 THz B. 20 MHz C. 200 MHz D. 2 GHz

Last Answer : A. 800 THz

The final amplifier of either FM or AM transmitter operates as A. Class B B. Class C C. Class A D. Class D

Description : The final amplifier of either FM or AM transmitter operates as A. Class B B. Class C C. Class A D. Class D

Last Answer : B. Class C

The line control unit (LCU) operates on the data digital form. A. Data communications equipment (DCE) B. UART C. Modem D. Data terminal equipment (DTE)

Description : The line control unit (LCU) operates on the data digital form. A. Data communications equipment (DCE) B. UART C. Modem D. Data terminal equipment (DTE)

Last Answer : D. Data terminal equipment (DTE)

In a triple conversion superheterodyne receiver, diode mixer stages are operated A. In the linear region B. In the nonlinear region C. As class A amplifiers D. As class B amplifiers

Description : In a triple conversion superheterodyne receiver, diode mixer stages are operated A. In the linear region B. In the nonlinear region C. As class A amplifiers D. As class B amplifiers

Last Answer : B. In the nonlinear region

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

Write the Abbreviation for the following File Extension 1. FMB 2. MMB 3. PLL?

Description : Write the Abbreviation for the following File Extension 1. FMB 2. MMB 3. PLL?

Last Answer : FMB ----- Form Module Binary. MMB ----- Menu Module Binary. PLL ------ PL/SQL Library Module Binary.

Draw and explain PLL as an FM demodulator.

Description : Draw and explain PLL as an FM demodulator.

Last Answer : Explanation:- FM signal which is to be demodulated is applied to input of PLL.VCO output must be identical to input signal if PLL is to remain locked. As PLL is locked, VCO ... error voltage represents the modulating signal. Thus at the error amplifier output we get demodulated FM output.

Draw and label PLL based FM detector.

Description : Draw and label PLL based FM detector.

Last Answer : Draw and label PLL based FM detector.

What is PLL? Explain its operation with a block diagram.

Description : What is PLL? Explain its operation with a block diagram.

Last Answer : PLL - A phase-locked loop or phase lock loop is a control system that generates an output signal whose phase is related to the phase of an input signal Block diagram  ... to the input frequency. The phase - locked loop goes through three states free running capture and phase lock.

Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Description : Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Last Answer : Operation:  The FM signal which is to be demodulated is applied at the input of the PLL.  the PLL is locked to the FM  The error voltage produced at ... using PLL ensures a high Linearity, between the instantaneous input frequency and VCO control voltage (error amplifier output)

In a PLL, lock occurs when the

Description : In a PLL, lock occurs when the (A) input frequency and the VCO frequency are the same (B) Phase error is 1800 (C) VCO frequency is double the input frequency (D) Phase error is 900

Last Answer : In a PLL, lock occurs when the input frequency and the VCO frequency are the same

Which of the following applications include a phase-locked loop (PLL) circuit?

Description : Which of the following applications include a phase-locked loop (PLL) circuit?  (1) Modems (2) AM decoders (3) Tracking filters (4) All of these 

Last Answer : All of these.

A phase-locked loop (PLL) is a feedback circuit consisting of a

Last Answer : A phase-locked loop (PLL) is a feedback circuit consisting of a phase detector, low-pass filter, VCO.

Which among the following statements are true with respect to electronic displacement in a covalent bond? (1) Inductive effect operates through a `pi`

Description : Which among the following statements are true with respect to electronic displacement in a covalent bond? (1) Inductive effect operates through a `pi`

Last Answer : Which among the following statements are true with respect to electronic displacement in a covalent bond? (1) Inductive ... 3 C. 2 and 3 D. 3 and 4

The genetic code operates through (A) The protein moiety of DNA (B) Cistrom of DNA (C) Nucleotide sequence of m RNA (D) The anticodons of tRNA

Description : The genetic code operates through (A) The protein moiety of DNA (B) Cistrom of DNA (C) Nucleotide sequence of m RNA (D) The anticodons of tRNA

Last Answer : Answer : C

The state operates through : (1) Political Party (2) Party President (3) Government (4) President

Description : The state operates through : (1) Political Party (2) Party President (3) Government (4) President

Last Answer : (3) Government Explanation: A government is the system by which a state or community is governed. It is the means by which state policy is enforced, as well as the mechanism for determining ... to the set of political systems and institutions that make up the organisation of a specific government.

A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Description : A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Last Answer : Answer: C

What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Description : What happens to the bandwidth of an antenna as it is shortened through the use of loading coils? A. It is increased B. It is decreased C. No change occurs D. It becomes flat

Last Answer : A. It is increased

What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Description : What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Last Answer : D. The frequency range over which an antenna can be expected to operate satisfactorily

The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Description : The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Last Answer : A. 500 to 600 ms

The wireless evolution is achieved through the GSM family of wireless technology platforms which include but except one of the following. Which one is NOT a member of the GSM family? A. GSM B. EDGE C. GPRS D. CDMA

Description : The wireless evolution is achieved through the GSM family of wireless technology platforms which include but except one of the following. Which one is NOT a member of the GSM family? A. GSM B. EDGE C. GPRS D. CDMA

Last Answer : D. CDMA

A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Description : A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Last Answer : C. Interpolator

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Description : Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Last Answer : A. N-type connector

The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem

Description : The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem

Last Answer : D. Modem

How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Description : How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Last Answer : B. Time division

Refers to a continuous tone generated in a local exchange terminal through a combination of two frequencies 350 Hz, and 440 Hz. A. Busy tone B. Call waiting tone C. Dial tone D. Standard tone

Description : Refers to a continuous tone generated in a local exchange terminal through a combination of two frequencies 350 Hz, and 440 Hz. A. Busy tone B. Call waiting tone C. Dial tone D. Standard tone

Last Answer : B. Call waiting tone

Referred to an oscillator signal “leak through” from a properly neutralized amplifier such as a master oscillator power amplifier. A. Carrier B. Stray signal C. Back wave D. Loss wave

Description : Referred to an oscillator signal “leak through” from a properly neutralized amplifier such as a master oscillator power amplifier. A. Carrier B. Stray signal C. Back wave D. Loss wave

Last Answer : C. Back wave

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna can be expected to perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Description : What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna ... perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Last Answer : C. The frequency range over which and antenna can be expected to perform well

____________ is the average rate of transmission of sound energy in a given direction through a cross sectional area of 1 sq.m. at right angle to the direction. A. Sound pressure B. Sound intensity C. Pressure variation D. Loudness

Description : ____________ is the average rate of transmission of sound energy in a given direction through a cross sectional area of 1 sq.m. at right angle to the direction. A. Sound pressure B. Sound intensity C. Pressure variation D. Loudness

Last Answer : B. Sound intensity

When electromagnetic wave are propagated through a waveguide, they A. are reflected from the walls but do not travel along them B. travel along all four walls of the waveguide C. travel along the broader walls of the guide D. travel through the dielectric without touching the walls

Description : When electromagnetic wave are propagated through a waveguide, they A. are reflected from the walls but do not travel along them B. travel along all four walls of the waveguide C. travel along the broader walls of the guide D. travel through the dielectric without touching the walls

Last Answer : A. are reflected from the walls but do not travel along them

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

What are the five stages in the Ladder of Problem Solving from "Thinking through Problem Solving"?

Description : What are the five stages in the Ladder of Problem Solving from "Thinking through Problem Solving"?

Last Answer : answer:http://www.changethis.com/21.ThinkingThrough The five stages: detection, inclination, capability, inquiry, skilled-response, and directed response. I know that's six. Maybe you only use one or the other of the last two?

Is not one of the stages groups go through when developing?

Description : Is not one of the stages groups go through when developing?

Last Answer : Need answer

The stages through which a plant or animal goes in its life?

Description : The stages through which a plant or animal goes in its life?

Last Answer : life cycle