The rough value of diffusion co-efficient of water vapor into air at 25°C may be about __________ cm2 /sec. (A) 0.25 (B) 2.5 (C) 1.25 (D) 0.0025

The rough value of diffusion co-efficient of water vapor into air at 25°C
may be about __________ cm2
/sec.
(A) 0.25
(B) 2.5
(C) 1.25
(D) 0.0025
by

1 Answer

Answer :

(A) 0.25
by

Related questions

Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric flow rate, cm3 /sec. V = volume, cm3 .) (A) Reactor dispersion number (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Description : Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric ... (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Last Answer : (D) None of these

The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Description : The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Last Answer : (B) 1/[L√(K/D1 )]

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move down the plane to that when it move up the plane would be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Description : A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move ... be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Last Answer : b. 5 ? 7

Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is ‘3k/l’. If the wall temperature on the outside is held at 25°C, what is the inside wall temperature in degree centigrade?(A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Description : Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is 3k/l'. If the wall temperature ... wall temperature in degree centigrade? (A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Last Answer : (C) 81.25

Pick out the wrong statement. (A) The binary diffusivity in liquids is of the order of 10 -5 cm2 /sec (B) Molecular diffusion in solid is much faster than that in liquids (C) Particles movement from higher concentration to lower concentration takes place in diffusion process (D) According to Poiseuille's law, the permeability decreases with increase in temperature for flow of a gas through a given capillary

Description : Pick out the wrong statement. (A) The binary diffusivity in liquids is of the order of 10 -5 cm2 /sec (B) Molecular diffusion in solid is much faster than that in liquids ( ... Poiseuille's law, the permeability decreases with increase in temperature for flow of a gas through a given capillary

Last Answer : (B) Molecular diffusion in solid is much faster than that in liquids

If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor. (A) Increase (B) Decrease (C) Not affect (D) Increase the condensing film co-efficient as well as

Description : If air (a non-condensing gas) is present in a condensing vapor stream, it will __________ the condensation rate of vapor. (A) Increase (B) Decrease (C) Not affect (D) Increase the condensing film co-efficient as well as

Last Answer : (B) Decrease

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only

A standard steel tape of length 30 m and cross-section 15 × 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of steel tape is 2.2 × 106 kg/cm2 , the correction to be applied is (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Last Answer : (A) - 0.000909 m

Experimental determination of __________ is done by wetted wall column method. (A) Diffusion co-efficient (B) Mass transfer co-efficient (C) NTU (D) None of these

Description : Experimental determination of __________ is done by wetted wall column method. (A) Diffusion co-efficient (B) Mass transfer co-efficient (C) NTU (D) None of these

Last Answer : (B) Mass transfer co-efficient

A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Description : A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Last Answer : (A) 7

In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said to have the same hydraulic roughness, when they have equal values of (A) Relative roughness (B) Absolute roughness (C) Friction co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Last Answer : (C) Friction co-efficient for flows at equal Reynold number

In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Description : In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Last Answer : (B) 1/KG = 1/KG + m/KL

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Description : The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Last Answer : (C) Some

The wet and 'dry bulb temperature for a vapour-gas mixture are 25°C and 30°C respectively. If the mixture is heated to 45°C at constant pressure, the wet bulb temperature will be __________ °C. (A) 25 (B) > 25 (C) < 25 (D) - 25

Description : The wet and 'dry bulb temperature for a vapour-gas mixture are 25°C and 30°C respectively. If the mixture is heated to 45°C at constant pressure, the wet bulb temperature will be __________ °C. (A) 25 (B) > 25 (C) < 25 (D) - 25

Last Answer : (B) > 25

The diffusion co-efficient in m2 /s. of acetic acid in benzene (liquid in liquid) is (A) 2.09 × 10 -4 (B) 2.09 × 10 -5 (C) 2.09 × 10 -9 (D) 2.09 × 10 -12

Description : The diffusion co-efficient in m2 /s. of acetic acid in benzene (liquid in liquid) is (A) 2.09 × 10 -4 (B) 2.09 × 10 -5 (C) 2.09 × 10 -9 (D) 2.09 × 10 -12

Last Answer : (A) 2.09 × 10 -4 (B) 2.09 × 10 -5

If the average compressive strength is 4000 kg/cm2 and standard deviation is 500, the co-efficient of variation is (A) 10 % (B) 12.5 % (C) 15 % (D) 18.5%

Description : If the average compressive strength is 4000 kg/cm2 and standard deviation is 500, the co-efficient of variation is (A) 10 % (B) 12.5 % (C) 15 % (D) 18.5%

Last Answer : Answer: Option B

Gaseous diffusion co-efficient increases with increase in the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Gaseous diffusion co-efficient increases with increase in the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Description : Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Last Answer : (A) Mass transfer co-efficient

Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Description : Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Last Answer : (A) Mass transfer co-efficient does not account for gas-liquid diffusion

Diffusion co-efficient of a metal in a solid solution depends upon its (A) Composition (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Diffusion co-efficient of a metal in a solid solution depends upon its (A) Composition (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of maximum compession of spring, neglecting friction to that while considering friction would be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Last Answer : a. More than one

1 kg of a saturated aqueous solution of a highly soluble component A at 60°C is cooled to 25°C. The solubility limits of A are (0.6 kgA/kg water) at 60°C and (0.2 kgA/kg water) at 25°C. The amount in kg of the crystals formed is: (A) 0.4 (B) 0.25 (C) 0.2 (D) 0.175

Description : 1 kg of a saturated aqueous solution of a highly soluble component A at 60°C is cooled to 25°C. The solubility limits of A are (0.6 kgA/kg water) at 60°C and (0.2 kgA/kg water) at 25°C. The amount in kg of the crystals formed is: (A) 0.4 (B) 0.25 (C) 0.2 (D) 0.175

Last Answer : (C) 0.2

A mixture of 10% C6H6 vapour in air at 25°C and 750 mm Hg has a dew point of 20°C. Its dew point at 30°C and 700 mm Hg will be around __________ °C. (A) 21.7 (B) 20 (C) 27.3 (D) 18.7

Description : A mixture of 10% C6H6 vapour in air at 25°C and 750 mm Hg has a dew point of 20°C. Its dew point at 30°C and 700 mm Hg will be around __________ °C. (A) 21.7 (B) 20 (C) 27.3 (D) 18.7

Last Answer : (D) 18.7

Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Description : Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Last Answer : A. 1.0025 MHz

In Joule's experiment, an insulated container contains 20 kg of waterinitially at 25°C. It is stirred by an agitator, which is made to turn by aslowly falling body weighing 40 kg through a height of 4 m. The process isrepeated 500 times. The acceleration due to gravity is 9.8 ms-2. Neglectingthe heat capacity of agitator, the temperature of water (in °C) is(A) 40.5(B) 34.4(C) 26.8(D) 25

Description : In Joule's experiment, an insulated container contains 20 kg of waterinitially at 25°C. It is stirred by an agitator, which is made to turn by a slowly falling body weighing 40 kg through a height of 4 m. The process is repeated ... temperature of water (in °C) is (A) 40.5 (B) 34.4 (C) 26.8 (D) 25

Last Answer : (B) 34.4

From above numerical find the static deflection A 0.0245 mm B 0.0025 mm C 0.0245 m D 0.0245 cm

Description : From above numerical find the static deflection A 0.0245 mm B 0.0025 mm C 0.0245 m D 0.0245 cm

Last Answer : C 0.0245 m

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

Research reactors are normally meant for (A) Producing high neutron flux 10 12 -10 13 neutrons/cm2 , sec and studying the effect of neutron bombardment on different materials (B) Accelerating the neutrons (C) Power generation (D) None of these

Description : Research reactors are normally meant for (A) Producing high neutron flux 10 12 -10 13 neutrons/cm2 , sec and studying the effect of neutron bombardment on different materials (B) Accelerating the neutrons (C) Power generation (D) None of these

Last Answer : (A) Producing high neutron flux 10 12 -10 13 neutrons/cm2 , sec and studying the effect of neutron bombardment on different materials

The binary diffusivity in gases at atmospheric conditions is about (A) 10 -9 cm/sec (B) 10 -1 cm2 /sec (C) 10 -3 sec/cm (D) 10 -4 cm2 /sec

Description : The binary diffusivity in gases at atmospheric conditions is about (A) 10 -9 cm/sec (B) 10 -1 cm2 /sec (C) 10 -3 sec/cm (D) 10 -4 cm2 /sec

Last Answer : (B) 10 -1 cm2 /sec

The unit of volumetric diffusivity is (A) cm2 /sec (B) cm/sec (C) cm3 /sec (D) cm2 /sec

Description : The unit of volumetric diffusivity is (A) cm2 /sec (B) cm/sec (C) cm3 /sec (D) cm2 /sec

Last Answer : (A) cm2 /sec

One poise (unit of absolute/dynamic viscosity) is equivalent to one (A) gm/cm2 . sec (B) gm/cm. sec (C) cm2 /sec (D) m2 /sec

Description : One poise (unit of absolute/dynamic viscosity) is equivalent to one (A) gm/cm2 . sec (B) gm/cm. sec (C) cm2 /sec (D) m2 /sec

Last Answer : (B) gm/cm. sec

Pick out the wrong conversion of absolute & kinematic viscosities. (A) 1 stoke = 1 cm2/sec (B) 1 N.sec/m2 = 10 paise (C) 1 stoke = 1 m2/sec (D) 1 m2/sec = 104 stokes

Description : Pick out the wrong conversion of absolute & kinematic viscosities. (A) 1 stoke = 1 cm2/sec (B) 1 N.sec/m2 = 10 paise (C) 1 stoke = 1 m2/sec (D) 1 m2/sec = 104 stokes

Last Answer : (C) 1 stoke = 1 m2/sec

Unit of viscosity in CGS system is (A) gm .cm-1 sec-1 (B) gm . cm2 . sec-2 (C) gm .cm-2, sec-1 (D) gm . cm . sec-1

Description : Unit of viscosity in CGS system is (A) gm .cm-1 sec-1 (B) gm . cm2 . sec-2 (C) gm .cm-2, sec-1 (D) gm . cm . sec-1

Last Answer : Option A

Approximate value of the modulus of elasticity for steel is about __________ × 10 6kg/cm2 . (A) 0.5 (B) 2 (C) 40 (D) 75

Description : Approximate value of the modulus of elasticity for steel is about __________ × 10 6kg/cm2 . (A) 0.5 (B) 2 (C) 40 (D) 75

Last Answer : (B) 2

Mass transfer co-efficient is directly proportional to DAB 0.5 , according to __________ theory. (A) Penetration (B) Surface renewal (C) Film (D) None of these

Description : Mass transfer co-efficient is directly proportional to DAB 0.5 , according to __________ theory. (A) Penetration (B) Surface renewal (C) Film (D) None of these

Last Answer : (A) Penetration

A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. Specific heat of block material is 0.4 kJ.kg-1. K-1. Ignoring the effect of expansion and contraction and also the heat capacity to tank, the total entropy change in kJ.kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Description : A solid metallic block weighing 5 kg has an initial temperature of 500°C. 40 kg of water initially at 25°C is contained in a perfectly insulated tank. The metallic block is brought into contact with water. Both of them come to equilibrium. ... .kg-1, K-1is (A) -1.87 (B) 0 (C) 1.26 (D) 3.91

Last Answer : (B) 0

The coefficient of permeability of soils, is generally expressed in (A) cm/sec (B) cm/minute (C) cm2 /sec (D) cm2 /minute

Description : The coefficient of permeability of soils, is generally expressed in (A) cm/sec (B) cm/minute (C) cm2 /sec (D) cm2 /minute

Last Answer : (A) cm/sec

What is 6.0025 to the nearest thousand?

Description : What is 6.0025 to the nearest thousand?

Last Answer : to the nearest thousand...zero ! - to the nearest thousandth...6.003

The graph shown in the illustration represents the speed droop curves of two equal capacity alternators about to be paralleled. When paralleled, the greater portion of the total load above 60% for each unit will be picked up _____________. EL-0025 A. by unit 'A' B. by unit 'B' C. equally by each unit D. none of the above

Description : The graph shown in the illustration represents the speed droop curves of two equal capacity alternators about to be paralleled. When paralleled, the greater portion of the total load above 60% for each unit will be picked up ... unit 'A' B. by unit 'B' C. equally by each unit D. none of the above

Last Answer : Answer: A

Unsaturated air (with dry bulb and wet bulb temperatures being 45°C and 25°C respectively) is passed through a water spray chamber maintained at 23°C. The air will be cooled and (A) Humidified with wet bulb temperature decreasingB) Humidified at constant wet bulb temperature(C) Dehumidified(D) None of these

Description : Unsaturated air (with dry bulb and wet bulb temperatures being 45°C and 25°C respectively) is passed through a water spray chamber maintained at 23°C. The air will be cooled and (A) ... temperature decreasing B) Humidified at constant wet bulb temperature (C) Dehumidified (D) None of these

Last Answer : (A) Humidified with wet bulb temperature decreasing

Unsaturated air (with dry and wet bulb temperatures being 35 and 25°C respectively) is passed through water spray chamber maintained at 35°C. The air will be (A) Cooled (B) Humidified (C) Both (A) & (B) (D) Dehumidified

Description : Unsaturated air (with dry and wet bulb temperatures being 35 and 25°C respectively) is passed through water spray chamber maintained at 35°C. The air will be (A) Cooled (B) Humidified (C) Both (A) & (B) (D) Dehumidified

Last Answer : (B) Humidified

If Thiele modulus is __________, then the pore diffusion resistance in a catalyst may be considered as negligible. (A) 0 (B) ∞ (C) < 0.5 (D) > 0.5

Description : If Thiele modulus is __________, then the pore diffusion resistance in a catalyst may be considered as negligible. (A) 0 (B) ∞ (C) < 0.5 (D) > 0.5

Last Answer : (C) < 0.5

The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Description : The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Last Answer : (B) 4 0.8

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Flue gas discharge velocity through chimney of a big thermal power plant may be around __________ m/sec. (A) 0.5 (B) 10 (C) 50 (D) 500

Description : Flue gas discharge velocity through chimney of a big thermal power plant may be around __________ m/sec. (A) 0.5 (B) 10 (C) 50 (D) 500

Last Answer : (B) 10

High seed germination in cucumber occurs under temperature range of: a. 20-25°C b. 25-30°C c. 15-25°C d. None of above

Description : High seed germination in cucumber occurs under temperature range of: a. 20-25°C b. 25-30°C c. 15-25°C d. None of above

Last Answer : 20-25°C